Hyundai HY2175 User Manual
  1. Manuals
  2. Brands
  3. Hyundai Manuals
  4. Drill
  5. HY2175
  6. User manual
Hyundai HY2175 User Manual

Hyundai HY2175 User Manual

18v cordless drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

1

Advertisement

Table of Contents
loading

Related Manuals for Hyundai HY2175

Summary of Contents for Hyundai HY2175

  • Page 2: Table Of Contents

    INDEX CONTENTS PAGE NO.S SAFETY 3 - 11 PART LOCATIONS OPERATION 13 - 16 MAINTENANCE STORAGE & TRANSPORTATION SPECIFICATION RECYCLING & PRODUCT DISPOSAL DECLARATION OF CONFORMITY CONTACT DETAILS WARRANTY MANUAL UPDATES...

  • Page 3: Safety

    1. SAFETY General Safety Notes. The operator of the machine is responsible for, and has a duty of care in making sure that the machine is operated safely and in accordance with the instructions in this user manual. Keep the manual safe and pass it on if the machine is loaned or sold to another user.
  • Page 4 1.10 Carbon Monoxide (where applicable). 1.11 Carbon monoxide is a colourless and odourless gas. Inhaling this gas can cause death as well as serious long term health problems such as brain damage. 1.12 The symptoms of carbon monoxide poisoning can include but are not limited to the following;...
  • Page 5 Contact a Doctor immediately or go to Hospital – let them know that you suspect 1.17 carbon monoxide poisoning. 1.18 DO NOT use in an enclosed area or moving vehicle. 1.20 General Fuel Safety (where applicable). CAUTION ALL FUELS ARE FLAMABLE Fire Hazard –...
  • Page 6 1.44 Are intact and have no signs of damage, to include but not limited to bare wires, chaffing, cuts and loose wiring. 1.45 If there are any signs of damage, the damage item MUST be taken out of service until the damage has been repaired by an electrically competent person. 1.46 All trailing cables should be routed so as not to cause any kind of trip hazard.
  • Page 7 1.63 Wear gloves and keep your hands warm. 1.64 Take regular breaks. 1.65 All of the above precautions may help reduce the risk of white finger disease but not rule out the carpal tunnel syndrome. Long-term and regular users are therefore recommended to observe the condition of your hands and fingers.
  • Page 8 2.10 When using this machine for the first time and before actual work, you MUST learn how to handle the machine from an experienced or skilled person. 2.11 Limit the amount of time using the machine continuously to somewhere around 10 minutes per session and take 10 to 20 minutes of rest between sessions.
  • Page 9 Crystalline silica from bricks, cement and other masonry products. Arsenic and chromium from chemically-treated lumber. 2.31 Your risk from these exposures varies, depending on how often you do this type of work. 2.32 To reduce your exposure to these chemicals, work in a well ventilated area and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
  • Page 10 2.44 Only charge the battery with the charger supplied. 2.45 Do not immerse the tool in water or any other liquids. 2.46 When transporting batteries, make sure their contacts are protected and properly insulated. 2.47 Store batteries in a cool dry place away from direct sunlight and extremes of temperature.
  • Page 11 2.64 DO NOT use this machine inside a confined space such as but not limited to a vehicle, house, garage, container, boat or building. Only use outside in a well ventilated area. 2.65 For air cooling a minimum of 1m is required all around the machine. 2.66 Maximum ambient temperature 40 degrees Celsius.

  • Page 12: Part Locations

    2. PART LOCATIONS Drill Chuck Direction Switch Torque Control On-Off Trigger 2 Speed Gear Switch 18v Battery LED Work Light 89 Piece Accessory Kit...

  • Page 13: Operation

    3. OPERATION NOTE Before operation, fully charge the battery for 3 to 5 hours. CHARGING THE BATTERY Check the accessories before use. Fully charge the battery for between 3 to 5 hours, check using the battery indicator lights. Press the battery check button: Battery too low Red + Yellow Battery half charged...
  • Page 14 Ensuring the correct orientation between the battery and the battery compartment on the drill. 3.10 Insert the rechargeable into the drill. 3.11 Do not apply force when inserting the battery. 3.12 The battery must be inserted completely until the battery retention clips on the sides of the battery compartment and click into place.
  • Page 15 TORQUE ADJUSTMENT NOTE The torque control knob should only be operated when the drill is not in use. Adjusting the torque setting whilst the drill is running, may cause irreversible damage to the drill that will not be covered by the warranty. 3.21 To adjust the torque setting, allow the drill to come to a complete stop.
  • Page 16 DRILLING METAL 3.37 For drilling metal, use a steel drill bit. 3.38 Always provide sufficient cooling with suitable non-flammable coolants. 3.39 Protect or fasten the work piece in a suitable vice or holder. 3.40 Mark the positions of the holes to be drilled with a centre punch. 3.41 Do not apply excessive pressure against the work piece with the drill.

  • Page 17: Maintenance

    Store the drill, accessories and instruction manual in the original packaging. Avoid areas of direct sunlight or varying temperature. Do not stack other items on top of the drill. Always store in a dry environment. 6. SPECIFICATION Model HY2175 Power Chuck 10mm Keyless Battery JH001-18v...

  • Page 18: Recycling & Product Disposal

    7. RECYCLING & PRODUCT DISPOSAL We do not offer a takeback scheme for the recovery of Waste Electrical Electronic Equipment (WEEE) & Batteries. Instead the responsibility to dispose of WEEE and or Batteries is passed onto you by So when it becomes necessary to dispose of your machine you must take it to your local Civic Amenity Site.

  • Page 19: Declaration Of Conformity

    8. DECLARATION OF CONFORMITY Genpower Ltd confirms that these Hyundai products conform to the following CE Directives. 2006/42/EC "Machinery" 2014/30/EU “Electro Magnetic Compatibility” 2011/65/EU “RoHS” EN 60745-1:2009 + A11:2010 EN 60745-2-1:2010 EN 60745-2-2: 2010 EN 55014-1:2006/+ A1:2009/+ A2:2011 EN 55014-2:2015...

  • Page 20: Contact Details

    9. CONTACT DETAILS POSTAL ADDRESS Genpower Ltd, Isaac Way, London Road, Pembroke Dock, Pembrokeshire. SA72 4RW. UK. TELEPHONE +44 (0) 1646 687880 +44 (0) 0164 686198 TECHNICAL EMAIL aftersales@genpower.co.uk WEBSITE www.hyundaipowerequipment.co.uk 10. WARRANTY To register your machine for the manufacturer’s warranty, please visit: https://www.hyundaipowerequipment.co.uk/warranty 11.

Table of Contents