Alcatel-Lucent OmniSwitch 6860 Hardware User's Manual
  1. Manuals
  2. Brands
  3. Alcatel-Lucent Manuals
  4. Network Router
  5. OmniSwitch 6860
  6. Hardware user's manual

Alcatel-Lucent OmniSwitch 6860 Hardware User's Manual

Hide thumbs Also See for OmniSwitch 6860:
Table of Contents

Advertisement

Quick Links

See also: Troubleshooting Manual
Part No. 060390-10, Rev. A
May 2014
OmniSwitch 6860/6860E
Hardware Users Guide
www.alcatel-lucent.com

Advertisement

Table of Contents
loading

Related Manuals for Alcatel-Lucent OmniSwitch 6860

Summary of Contents for Alcatel-Lucent OmniSwitch 6860

  • Page 1 Part No. 060390-10, Rev. A May 2014 OmniSwitch 6860/6860E Hardware Users Guide www.alcatel-lucent.com...
  • Page 2 This user guide documents OmniSwitch 6860 hardware, including chassis and associated components. The specifications described in this guide are subject to change without notice. Copyright© 2014 by Alcatel-Lucent. All rights reserved. This document may not be reproduced in whole or in part without the express written permission of Alcatel-Lucent.

  • Page 3: Table Of Contents

    How is the Information Organized? ................... x Documentation Roadmap ....................xi Related Documentation ....................xiii Technical Support ......................xiv Chapter 1 OmniSwitch 6860 ......................1-1 OmniSwitch 6860 Availability Features .................1-3 Power Supply Redundancy ..................1-3 Hot-Swapping ......................1-3 Hardware Monitoring ....................1-4 Chapter 2 Getting Started ......................2-1 Installing the Hardware ....................2-1...
  • Page 4 Viewing Your Changes ..................2-10 Saving Your Changes .....................2-10 Chapter 3 Chassis and Power Supplies ..................3-1 OmniSwitch 6860 Chassis Details ..................3-2 Basic Models - Non-PoE ..................3-2 OS6860-24 Front Panel ..................3-2 OS6860-24 Rear Panel ..................3-2 OS6860-24 Chassis Specifications ..............3-3 OS6860-48 Front Panel ..................3-4 OS6860-48 Rear Panel ..................3-4...
  • Page 5 OmniSwitch Backup Power Shelf/System (BPS) Rear Panel ......4-2 Supported Configurations ....................4-3 Unsupported Configurations ..................4-3 Specifications ........................4-4 Power Supply Redundancy ..................4-5 Hot Swapping OS-BPS Power Supplies ..............4-5 Considerations if OS-BPS is the Only Power Source In a Virtual Chassis ..4-5 OmniSwitch 6860 Hardware Users Guide May 2014...
  • Page 6 Configuring the Total Power Available to a slot ..........5-6 Setting Port Priority Levels ................5-7 Setting the Capacitor Detection Method ............5-7 Understanding Priority Disconnect .................5-8 Setting Priority Disconnect Status ................5-8 Monitoring Power over Ethernet via CLI ..............5-11 OmniSwitch 6860 Hardware Users Guide May 2014...
  • Page 7 Advertencia sobre una apropiada conexión a tierra ........A-13 Leer “información importante de seguridad” ..........A-13 Advertencia de acceso restringido ..............A-13 Advertencia de pulsera antiestática ..............A-13 Clase de seguridad ..................A-13 Advertencia de fuentes de poder ..............A-13 OmniSwitch 6860 Hardware Users Guide May 2014...
  • Page 8 Contents viii OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 9: About This Guide

    About This Guide This OmniSwitch 6860 Hardware Users Guide describes OmniSwitch 6860 switch components and basic switch hardware procedures. Supported Platforms The information in this guide applies only to OmniSwitch 6860 switches. Who Should Read this Manual? The audience for this users guide is network administrators and IT support personnel who need to configure, maintain, and monitor switches and routers in a live network.

  • Page 10: What Is In This Manual

    Each chapter in this guide focuses on a specific hardware component or a set of hardware components. All descriptive, technical specification, and procedural information for a hardware component can be found in the chapter dedicated to that component. OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 11: Documentation Roadmap

    OmniSwitch AOS Release 8 Release Notes A “Getting Started” chapter is included in the OmniSwitch 6860 Hardware Users Guide. This chapter provides all the information you need to get your switch up and running the first time. It also includes succinct overview information on fundamental aspects of the switch.
  • Page 12 This guide includes syntax, default, usage, example, related CLI command, and CLI-to-MIB variable mapping information for all CLI commands supported by the switch. This guide can be consulted anytime during the configuration process to find detailed and specific information on each CLI command. OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 13: Related Documentation

    Related Documentation The following are the titles and descriptions of all the OmniSwitch 6860 user manuals: • OmniSwitch 6860/6860E Hardware Users Guide Complete technical specifications and procedures for all OmniSwitch 6860 chassis, power supplies, fans, and Network Interface (NI) modules.

  • Page 14: Technical Support

    With 24-hour access to Alcatel-Lucent’s Service and Support web page, you’ll be able to view and update any case (open or closed) that you have reported to Alcatel-Lucent’s technical support, open a new case or access helpful release notes, technical bulletins, and manuals.

  • Page 15: Chapter 1 Omniswitch 6860

    1 OmniSwitch 6860 Refer to the information below for OmniSwitch 6860 (OS6860) models and components. Model Number Description OS6860-24 Fixed-configuration chassis in a 1U form factor with 24 10/100/1000 Base-T ports, four fixed SFP+ (1G/10G) ports and two 20G Virtual Chassis link ports.
  • Page 16 150W power supply.) All models include one console connector (for use with Micro USB-to-USB cable, included); one USB connector (for use with Alcatel-Lucent flash drive or Bluetooth dongle, not included); and one RS-232 connector.

  • Page 17: Omniswitch 6860 Availability Features

    The following hardware components can be hot-swapped: • Power supplies • Transceivers • Plug-in modules Note. For information on adding and removing power supplies and plug-in modules, refer to Chapter 3, “Chassis and Power Supplies.” OmniSwitch 6860 Hardware Users Guide May 2014 page 1-3...

  • Page 18: Hardware Monitoring

    The user enters “show” commands that output information to the console. The show commands for all the features are described in detail in the OmniSwitch CLI Reference Guide. page 1-4 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 19: Chapter 2 Getting Started

    Electrical Requirements Note. Alcatel-Lucent switches must be installed by a professional installer. It is the responsibility of the installer to ensure that proper grounding is available and that the installation meets applicable local and national electrical codes.

  • Page 20: Unpacking And Installing The Switch

    To protect your switch components from damage, read all unpacking recommendations and instructions carefully before beginning. Unpack your OmniSwitch 6860 chassis as close as possible to the location where it will be installed. Items Included Your OmniSwitch 6860 includes the following items: •...

  • Page 21: Airflow Considerations

    Chassis Top View Note. Clearance is not required at the top and bottom of the chassis. Mounting the Switch For information on mounting OmniSwitch 6860 switches, refer to the Chapter 3, “Chassis and Power Supplies.” OmniSwitch 6860 Hardware Users Guide...

  • Page 22: Connections And Cabling

    EMP is connecting. Refer to the information below: EMP to a Switch Straight-through EMP to a Computer or Crossover Workstation For information on manually configuring Ethernet ports, refer to the OmniSwitch AOS Release 8 Network Configuration Guide. page 2-4 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 23: Booting The Switch

    If the LEDs do not display as indicated, make sure the boot process is complete. If the LEDs do not display as indicated following a complete boot sequence, contact Alcatel-Lucent Customer Support. For complete information on LED states, refer to “Chassis Status LEDs”...

  • Page 24: Your First Login Session

    Welcome to the Alcatel-Lucent OS6860E-P48 8.1.1, April 15, 2014. Copyright (c) 1994-2014 Alcatel-Lucent. All Rights Reserved. OmniSwitch(tm) is a trademark of Alcatel-Lucent, registered in the United States Patent and Trademark Office. -> Note. A user account includes a login name, password, and user privileges. Privileges determine whether the user has read or write access to the switch and which commands the user is authorized to execute.

  • Page 25: Setting Ip Address Information For The Emp

    (i.e. TELNET, FTP, HTTP, SSH or SNMP) until you have unlocked these remote session types. See “Unlocking Session Types” on page 2-8 for more information. OmniSwitch 6860 Hardware Users Guide May 2014 page 2-7...

  • Page 26: Unlocking Session Types

    Your First Login Session Getting Started Unlocking Session Types Security is a key feature on OmniSwitch 6860 switches. As described on page 2-6, when you access the switch for the first time, you must use a direct console port connection. All other session types (Telnet, FTP, WebView, and SNMP) are locked out until they are manually unlocked by the user.

  • Page 27: Setting The System Time Zone

    However, if no labeling system has been implemented or if you need to determine a switch’s location from a remote site, entering a system location can be very useful. To specify a system location, use the system location command. OmniSwitch 6860 Hardware Users Guide May 2014 page 2-9...

  • Page 28: Viewing Your Changes

    To view your current changes, enter show system at the CLI prompt. Saving Your Changes Once you have configured this basic switch information, save your changes by entering write memory at the CLI command prompt. page 2-10 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 29: Chassis And Power Supplies

    3 Chassis and Power Supplies This chapter includes detailed information on the OmniSwitch 6860 switch. Topics include: • Chassis details and technical specifications: Basic Models - Non-PoE OS6860-24, page 3-2. OS6860-48, page 3-4. Basic Models - PoE OS6860-P24, page 3-6.

  • Page 30: Omniswitch 6860 Chassis Details

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply/Fan Tray Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 31: Os6860-24 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-3...

  • Page 32: Os6860-48 Front Panel

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply/Fan Tray Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 33: Os6860-48 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-5...

  • Page 34: Basic Models - Poe

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) PoE Power Supply Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 35: Os6860-P24 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-7...

  • Page 36: Os6860-P48 Front Panel

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) PoE Power Supply Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 37: Os6860-P48 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-9...

  • Page 38: Enhanced Models - Non-Poe

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply/Fan Tray Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 39: Os6860E-24 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-11...

  • Page 40: Os6860E-48 Front Panel

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply/Fan Tray Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 41: Os6860E-48 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-13...

  • Page 42: Os6860E-U28 Front Panel

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply/Fan Tray Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 43: Os6860E-U28 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-15...

  • Page 44: Enhanced Models - Poe

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 45: Os6860E-P24 Chassis Specifications

    *Note On Chassis Versus Ambient Temperatures. Chassis temperature refers to the sensor reading of the internal switch temperature (threshold or danger). Ambient temperature refers to the approximate room temperature. The ambient temperature will typically be lower than the chassis temperature. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-17...

  • Page 46: Os6860E-P48 Front Panel

    OmniSwitch Backup Power Supply (OS-BPS) Connector (See note below.) Power Supply Bays Note. Only the Alcatel-Lucent OnmiSwitch BPS may be attached to the DB25 backup power supply connector. Refer to the switch’s technical specifications for max. power ratings for this connector.

  • Page 47: Os6860E-P48 Chassis Specifications

    System Diagnostics and/or AOS bootup failed Solid Green This unit is the master unit Solid Amber This unit is a slave unit This unit is in shutdown mode or is not part of a VC. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-19...
  • Page 48 Port LEDs Solid Green Valid port link (non-PoE) Blinking Green Valid port link with activity (non-PoE) Solid Amber Valid port link (PoE) Blinking Amber Valid port link with activity (PoE) page 3-20 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 49: General Mounting Recommendations

    Reliable Earthing. Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch (e.g., use of power strips). OmniSwitch 6860 Hardware Users Guide May 2014 page 3-21...

  • Page 50: Airflow Recommendations

    Sides. 2 inches minimum at left and right sides. Front. 6 inches minimum at front of chassis. Chassis Top View Note. Clearance is not required at the top and bottom of the chassis. page 3-22 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 51: Blank Cover Panels

    When installing blank cover panels over power supply slots, orient the cover panels with the arrows pointing up. Face arrow up when installing. Insert the blank cover panel in the empty chassis slot and secure using attachment screws (provided). OmniSwitch 6860 Hardware Users Guide May 2014 page 3-23...

  • Page 52: Rack-Mounting

    The chassis has rack-mount flanges that support standard 19-inch rack mount installations. • Alcatel-Lucent does not provide rack-mount screws. Use the screws supplied by the rack vendor. • To prevent a rack from becoming top heavy, it is recommended that you install the switch at the bottom of the rack whenever possible.
  • Page 53 Clip in “In” (engaged) position “CLICK” Secure the flange to the chassis using the attachment screw (provided). Repeat steps 1 through 4 for the flange on the opposite side of the chassis. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-25...

  • Page 54: Installing The Chassis In The Rack

    Once the holes are aligned, the second person should insert a screw through the bottom hole on each flange. Tighten both screws until they are secure. Install the remaining screws in the top hole of each flange. Be sure that all screws are securely tightened. page 3-26 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 55: Standalone (Non-Rack Mounted) Installations

    Place the switch on the tabletop “right side up.” Note. Never attempt to operate a switch while it is placed on its top or side. Connect network and management cables as needed. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-27...

  • Page 56: Power Supplies

    OS6860-BPPX 920W AC OS6860-P24, OS6860E-P24, OS6860-P48, OS6860E-P48 PoE PSU OmniSwitch 6860 power supplies are located at the rear of the switch chassis. Refer to “OmniSwitch 6860 Chassis Details” for more information on component locations. Two slots are provided. If a second power supply is installed, it will assume a standby role.

  • Page 57: Dying Gasp

    Use the swlog output socket command to add a Syslog station. Refer to the Using Switch Logging Configuration chapter in the Network Configuration Guide for information on configuring a Syslog server. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-29...

  • Page 58: Os6860-Bp 150W Power Supply

    Flashing Green/Red Power supply warning Solid Red Power supply failure No AC power is being provided to any power supply installed in the chassis; all power supplies are effectively off page 3-30 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 59: Os6860-Bp-D 150W Dc Power Supply

    Flashing Green/Red Power supply warning Solid Red Power supply failure No power is being provided to any power supply installed in the chassis; all power supplies are effectively off OmniSwitch 6860 Hardware Users Guide May 2014 page 3-31...

  • Page 60: Os6860-Bpph 600W Power Supply

    AC OK LED Solid Red There is an AC power issue DC OK LED Solid Green DC power is good DC OK LED Solid Red There is a DC power issue page 3-32 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 61: Os6860-Bppx 920W Power Supply

    AC OK LED Solid Red There is an AC power issue DC OK LED Solid Green DC power is good DC OK LED Solid Red There is a DC power issue OmniSwitch 6860 Hardware Users Guide May 2014 page 3-33...

  • Page 62: Dc Power Supply Connections

    Observe proper polarity when connecting to a fuse panel. The cable wire leads must be connected as follows: • Green/yellow - ground • Black - return • Red - -48VDC Note. The battery return conductor is an Isolated DC Return (DC-1). page 3-34 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 63: Installing Power Supplies

    Insert the power supply into a power supply bay at the rear of the chassis and slide it back until it is securely seated in the chassis backplane. When the connector is fully seated, the lock tab will click and hold the power supply in place. Lock Tab OmniSwitch 6860 Hardware Users Guide May 2014 page 3-35...
  • Page 64 Plug the power cord (provided) into the power supply’s socket. Note. The chassis does not provide an on/off switch. Connecting a the power supplies to a power source will boot the switch. page 3-36 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 65: Removing Power Supplies

    Pressing the lock tab toward the center of the power supply, as shown, will free the power supply from the chassis. Lock Tab OmniSwitch 6860 Hardware Users Guide May 2014 page 3-37...
  • Page 66 While pressing the lock tab, pull the power supply straight back and out of the chassis slot. Note. If you are not replacing the power supply, be sure to install a blank cover panel over the empty power supply bay. page 3-38 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 67: Grounding The Chassis

    Use this connector to supplement the ground provided by the AC power cord. To do so, install a Panduit Grounding Lug (type LCD8-10A-L) using 8AWG copper conductors to the paint-free area. Refer to the rear chassis views on page 3-2 for location details. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-39...

  • Page 68: Os6860 Fantray Nonpoe Fan Tray

    OS6860-24, OS6860E-24, OS6860-48, OS6860E-48, OS6860E-U28 OS6860 FANTRAY NONPOE LED States LED State Description Solid Green Fan tray is receiving power and operating normally The fan tray is off or a failure has occurred page 3-40 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 69: Monitoring Chassis Components

    15-93 UNDER THRESHOLD 2/CMMA 15-85 UNDER THRESHOLD 2/Slot1 15-85 UNDER THRESHOLD For more information about this command, see the “Chassis Management and Monitoring Commands” chapter in the OmniSwitch CLI Reference Guide. OmniSwitch 6860 Hardware Users Guide May 2014 page 3-41...

  • Page 70: Temperature Errors

    The danger threshold is factory-set and cannot be configured by the user. Addressing danger threshold temperature conditions may include: • Checking for a chassis airflow obstruction • Checking the ambient room temperature page 3-42 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 71: Chapter 4 Omniswitch Backup Power Shelf/System (Bps)

    A maximum of two system power supplies and three POE power supplies can be installed in a single OS-BPS chassis. If two or more like power supplies are installed, each will share the power load. OS-BPS Chassis Front OS-BPS Chassis Rear OmniSwitch 6860 Hardware Users Guide May 2014 page 4-1...

  • Page 72: Chassis Details

    OmniSwitch Backup Power Shelf/System (BPS) Rear Panel OmniSwitch BPS Item Description Chassis Grounding Lug DB25 Power Connectors (providing system power to OS6860 switches) Power Cord Connectors for PoE Power Supplies Chassis LEDs page 4-2 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 73: Supported Configurations

    OmniSwitch Backup Power Shelf/System (BPS) Supported Configurations Supported Configurations The OmniSwitch BPS can be used to provide redundancy to the OmniSwitch 6860 in multiple configurations as described below: • Single OmniSwitch 6860 Virtual Chassis (VC), from one to eight switches •...

  • Page 74: Specifications

    (threshold or danger). Ambient temperature refers to the temperature of the room and are approximations. The ambient temperature will be less than the chassis temperature and will vary for each model due to different airflow characteristics. page 4-4 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 75: Chassis Status Leds

    In transitional state (e.g. performing diagnostics or booting) C1 - C8 Solid Green Both power supplies are functional Solid Amber One power supply is functional ECO LED Solid Green Power save mode is currently active OmniSwitch 6860 Hardware Users Guide May 2014 page 4-5...

  • Page 76: Os-Bps Connector Priority

    By default, connector 1 receives the highest priority and connector 8 receives the lowest priority. Additional default priorities are specified below. Connector Default Priority Note. The higher the numerical priority value, the higher the connector priority. page 4-6 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 77: Mounting The Chassis

    Refer to the following important guidelines regarding airflow: Rear. 6 inches minimum at rear of chassis. Sides. 2 inches minimum at left and right sides. Front. 6 inches minimum at front of chassis. Chassis Top View OmniSwitch 6860 Hardware Users Guide May 2014 page 4-7...

  • Page 78: Omniswitch Bps Airflow

    Each power supply draws air through intake vents at the front of the power supply. The air is then directed straight through each power supply and out the rear chassis vent. OmniSwitch BPS Airflow page 4-8 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 79: Blank Cover Panels

    Note. Because they regulate airflow and help protect internal chassis components, blank cover panels should be installed over empty power supply bays at all times. Blank Panels and Chassis Airflow OmniSwitch 6860 Hardware Users Guide May 2014 page 4-9...

  • Page 80: Rack-Mounting

    The chassis has rack-mount flanges that support standard 19-inch rack mount installations. • Alcatel-Lucent does not provide rack-mount screws. Use the screws supplied by the rack vendor. • To prevent a rack from becoming top heavy, it is recommended that you install the chassis at the bottom of the rack whenever possible.
  • Page 81 Note. The chassis installation should be level. Be sure that the rear flanges are aligned with the corresponding holes at the front of the rack. Insert rack mount screws through the rear rack mount flanges and tighten. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-11...

  • Page 82: Mid-Mounting The Chassis In The Rack

    One person should lift and position the chassis until the mid-mount flanges are flush with the rack post. Align the holes in the flanges with the rack holes marked in step 3. page 4-12 OmniSwitch 6860 Hardware Users Guide May 2014...
  • Page 83 Once the holes are aligned, the second person should insert a screw through the bottom hole on each flange. Tighten both screws until they are secure. Once the flanges are aligned, install the remaining screws. Be sure that all screws are securely tightened. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-13...

  • Page 84: Power Supplies

    Humidity (Operating) 5% to 95% non-condensing Humidity (Non-Operating) 5% to 95% non-condensing Airflow This power supply provides front-to-back airflow only for OS-BPS applications. See “Airflow Recommendations” on page 4-7 for more information. page 4-14 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 85: Ac Power Supply Led States

    No AC power is being provided to this power supply Flashing Green/Red Power supply warning Solid Red Power supply failure No AC power is being provided to any power supply installed in the chassis; all power supplies are effectively off OmniSwitch 6860 Hardware Users Guide May 2014 page 4-15...

  • Page 86: Omniswitch Bps Poe Power Supply

    Storage Temperature -40°C to +85°C Humidity (Operating) 5% to 95% non-condensing Humidity (Non-Operating) 5% to 95% non-condensing Airflow This power supply provides front-to-back airflow only. “Airflow Recommendations” on page 4-7 more information. page 4-16 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 87: Omniswitch Bps Poe Power Supply Led States

    Power Supplies OmniSwitch BPS PoE Power Supply LED States Description On: Input OK Blinking: Input out of limits On: Output OK Blinking: Power supply overload On: Over-temp warning Blinking: Service ON: Fault OmniSwitch 6860 Hardware Users Guide May 2014 page 4-17...

  • Page 88: Omniswitch Bps Power Connections

    “C1” will have the highest power budget priority; the switch connected to connector port “C2” will have the next highest priority, etc. For additional information, refer to “OS-BPS Connector Priority” on page 4-6 for more information. OS6860 DB25 Connector 1 Meter Connector Cable OmniSwitch BPS DB25 Connector page 4-18 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 89: Installing And Connecting System Power

    Note. The chassis does not provide an on/off switch. Connecting a minimum of one system power supply and one PoE power supply to a power source will power on the OS-BPS chassis and any attached switches. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-19...

  • Page 90: Installing Poe Power Supplies

    Slide the power supply back until the left side of the lever catches the sheet metal tab at the inside top of the chassis. Gently close the lever until it locks into place securing the power supply into the chassis. page 4-20 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 91: Connecting Poe Power

    Note. The chassis does not provide an on/off switch. Connecting a minimum of one system power supply and one PoE power supply to a power source will power on the OS-BPS chassis and any attached switches. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-21...

  • Page 92: Grounding The Chassis

    The “Earth Ground” for all AC sources must be a solid common ground that does not have any electrical potential (voltage) between them. Refer to the rear chassis views on page 4-2 for location details. page 4-22 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 93: Disconnecting A Chassis From The Os-Bps

    Lock Tab Note. If you are not replacing the power supply, be sure to install a blank cover panel over the empty power supply bay. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-23...

  • Page 94: Removing Poe Power Cords From The Os-Bps Chassis

    OmniSwitch Backup Power Shelf/System (BPS) Removing PoE Power Cords from the OS-BPS Chassis Swing the retainer clip away from the power cord connector. Pull the cord straight out of the connector socket. page 4-24 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 95: Removing Poe Power Supplies

    Lock Tab Note. If you are not replacing the power supply, be sure to install a blank cover panel over the empty power supply bay. OmniSwitch 6860 Hardware Users Guide May 2014 page 4-25...

  • Page 96: Monitoring Omniswitch Bps Components

    To display the connector priority for power supplies currently installed in the OmniSwitch BPS chassis, use the show power-shelf bps-connector-priority command. Note. For detailed information on these commands, as well as OmniSwitch BPS configuration commands, refer to the OmniSwitch CLI Reference Guide. page 4-26 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 97: Chapter 5 Managing Power Over Ethernet (Poe)

    As the switches fully support 10/100/1000 Ethernet connectivity, you may also attach non-PD equipment, such as computer workstations, printers, servers, etc. to the PoE ports. Important. Alcatel-Lucent recommends that PoE-enabled switches with attached IP telephones should have operational power supply redundancy at all times for 911 emergency requirements. In addition, both the switch and the power supply should be plugged into an Uninterruptible Power Source (UPS).

  • Page 98: In This Chapter

    Note. You can also monitor all chassis components and manage many chassis features, including Power over Ethernet, with WebView, Alcatel-Lucent’s embedded web-based device management application. WebView is an interactive and easy-to-use GUI that can be launched from the OmniVista or a web browser.

  • Page 99: Power Over Ethernet Specifications

    Managing Power over Ethernet (PoE) Power over Ethernet Specifications Power over Ethernet Specifications The table below lists general specifications for Alcatel-Lucent’s Power over Ethernet support. For more detailed power supply and Power Source Equipment (PSE) specifications, refer to Chapter 3, “Chassis and Power Supplies.”...

  • Page 100: Viewing Poe Status

    920W power supply- 780W entire slot 600W power supply - 450W Power priority level for a port lanpower priority Capacitor detection method lanpower capacitor-detection Disabled Priority disconnect status lanpower slot priority-disconnect Enabled page 5-4 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 101: Understanding And Modifying The Default Settings

    If power to a particular port has been administratively disconnected, you can reactivate power to the port using the lanpower port admin-state command. For example: -> lanpower port 2/1/1-24 admin-state enable OmniSwitch 6860 Hardware Users Guide May 2014 page 5-5...

  • Page 102: Configuring The Total Power Available To A Port

    As with the maximum port power allowance, the user can either increase or decrease this value based on the allowed ranges. Important. Decreasing the slot-wide power could cause lower priority ports to lose power if the new value is less than the total PoE power currently being consumed. page 5-6 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 103: Setting Port Priority Levels

    Note. The capacitive detection method should only be enabled to support legacy IP phones. This feature is not compatible with IEEE specifications. Please contact your Alcatel-Lucent sales engineer or Customer Support representative to find out which Alcatel-Lucent IP phones models need capacitive detection enabled.

  • Page 104: Understanding Priority Disconnect

    For example: -> lanpower slot 2/1 priority-disconnect disable Enabling Priority Disconnect To enable priority disconnect, use the lanpower slot priority-disconnect command. For example: -> lanpower slot 2/1 priority-disconnect enable page 5-8 OmniSwitch 6860 Hardware Users Guide May 2014...
  • Page 105 When a PD is being connected to a port with a lower priority level than all other in the slot, the incoming PD will be denied power, regardless of its physical port number. Devices connected to other higher-prior- ity will continue operating without interruption. OmniSwitch 6860 Hardware Users Guide May 2014 page 5-9...

  • Page 106: Priority Disconnect Is Disabled

    When priority disconnect is disabled, power will be denied to any incoming PD, regardless of its port priority status (i.e., low, high, and critical) or physical port number (i.e., 1–24). page 5-10 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 107: Monitoring Power Over Ethernet Via Cli

    Undefined 30000 Undefined 30000 Undefined Slot 3 Max Watts 150 1 Power Supplies Available Note. For detailed information on show lanpower command output, refer to the OmniSwitch CLI Refer- ence Guide. OmniSwitch 6860 Hardware Users Guide May 2014 page 5-11...
  • Page 108 Monitoring Power over Ethernet via CLI Managing Power over Ethernet (PoE) page 5-12 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 109: Regulatory Compliance And Safety Information

    A Regulatory Compliance and Safety Information This appendix provides information on regulatory agency compliance and safety for OmniSwitch 6860 switches. Declaration of Conformity: CE Mark This equipment is in compliance with the essential requirements and other provisions of Directive 2004/108/EC (EMC), 2006/95/EC (LVD), 91/263/EEC (Telecom Terminal Equipment, if applicable), 1999/5/EC (R&TTE, if applicable).

  • Page 110: China Rohs: Hazardous Substance Table

    对销售之日的所售产品, 本表显示, 阿尔卡特朗讯公司供应链的电子信息产品可能包含这些物质。注意: 在所售产 品中可能会也可能不会含有所有所列的部件。 This table shows where these substances may be found in the supply chain of Alcatel-Lucent electronic information products, as of the date of sale of the enclosed product. Note that some of the component types listed above may or may not be a part of the enclosed product.
  • Page 111 Regulatory Compliance and Safety Information China RoHS: Hazardous Substance Table Products are packaged using one or more of the following packaging materials: Corrugated Cardboard Corrugated Fiberboard Low-Density Polyethylene OmniSwitch 6860 Hardware Users Guide May 2014 page A-3...

  • Page 112: Standards Compliance

    The product bears the CE mark. In addition it is in compliance with the following other safety and EMC standards. Note. All hardware switching modules used in an OmniSwitch 6860 switch comply with Class A standards. Modules with copper connectors meet Class A requirements using unshielded (UTP) cables.
  • Page 113 (2250 V DC on all Ethernet ports) Environmental Standards • ETS 300 019 Storage Class 1.1 • ETS 300 019 Transportation Class 2.3 • ETS 300 019 Stationary Use Class 3.1 OmniSwitch 6860 Hardware Users Guide May 2014 page A-5...

  • Page 114: Fcc Class A, Part 15

    CISPR22 Class A warning This is a Class A product. In a domestic environment, this product may cause radio interference. Under such circumstances, the user may be requested to take appropriate countermeasures. page A-6 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 115: Vcci

    Under such circumstances, the user may be requested to take appropriate countermeasure. Class 1M Laser Warning CLASS 1M LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS. OmniSwitch 6860 Hardware Users Guide May 2014 page A-7...

  • Page 116: Translated Safety Warnings

    Deutsch: Dieses Gerät soll nur von Personal installiert oder gewartet werden, welches in elektrischen und mechanischen Grundlagen ausgebildet ist. Español: Estos equipos deben ser instalados y atendidos exclusivamente por personal adecuadamente formado y capacitado en técnicas eléctricas y mecánicas. page A-8 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 117: Invisible Laser Radiation Warning

    Netzverbindungen getrennt sind bevor das Gerät gewartet oder bewegt wird. Español: Antes de empezar a trabajar con un sistema, asegurese que el interruptor está cerrado y el cable eléctrico desconectado. OmniSwitch 6860 Hardware Users Guide May 2014 page A-9...

  • Page 118: Proper Earthing Requirement Warning

    Erde angeschlossen werden. Español: Para EMC/EMI, cada fuente de alimentación de CC/CC requiere que el cable de tierra esté conectado desde cada fuente de alimentación de CC/CC a la conexión a tierra común. page A-10 OmniSwitch 6860 Hardware Users Guide May 2014...

  • Page 119: Read Important Safety Information Warning

    Español: Debido a las descargas electrostáticas (ESD) puede dañar los componentes del interruptor, debe seguir los procedimientos adecuados para eliminar la EDS de su persona y sus alrededores antes de manipular los componentes del interruptor. OmniSwitch 6860 Hardware Users Guide May 2014 page A-11...

  • Page 120: Instrucciones De Seguridad En Español

    Deseche las baterías usadas según las instrucciones del fabricante. Las instrucciones del fabricante son como sigue: Devuelva el módulo con la batería del litio a Alcatel-Lucent. La batería del litio será substituida en la fábrica de Alcatel-Lucent.

  • Page 121: Advertencia Sobre Una Apropiada Conexión A Tierra

    Para este propósito, Alcatel-Lucent proporciona una pulsera antiestática y un terminal que pone a tierra situados cerca de la parte superior derecha del chasis. Para que la pulsera antiestática sea eficaz en la eliminación de ESD, las fuentes de alimentación se deben instalar en el chasis y enchufar en las salidas de CA con descarga a...
  • Page 122 Instrucciones de seguridad en español Regulatory Compliance and Safety Information page A-14 OmniSwitch 6860 Hardware Users Guide May 2014...

This manual is also suitable for:

Omniswitch 6860e

Table of Contents