Related Manuals for Horizon Fitness Titan XG60
Summary of Contents for Horizon Fitness Titan XG60
- Page 1 Horizon® Titan XG60-Installation and Operations Manual Air Cleaning Equipment, Inc. sales@horizondehumidifiers.com 14021 NC Hwy 50, Surf City, NC, 28445 Phone:(919) 258-3330x3 Fax: (919)258-3394...
-
Page 2: Table Of Contents
Table of Contents Warranty Registration Safety Notes Identification Electrical Supply Principle of Operation Installation Key Functions Indicator Lights Remote Control Operating Instructions Diagram Maintenance Dehumidifier Storage Ducted Applications Troubleshooting Spare Parts Warranty Information... -
Page 3: Warranty Registration
Warranty Registration Congratulations on purchasing a new Horizon Dehumidifier. Your new dehumidifier comes with an extensive warranty plan. To register, simply visit: www.horizondehumidifiers.com/warranty. Be sure to note your dehumidifier serial number as you will need it for registration. Safety Notes •... -
Page 4: Identification
For future reference, write down the model, serial number, and date of purchase for your dehumidifier. This is extremely helpful if you need to seek assistance in the future. The data label on the side of your unit has key characteristics of your specific unit. Model Number: Horizon Titan XG60 Serial Number: Date of Purchase: For additional questions concerning your dehumidifier, the following options are available:... -
Page 5: Key Functions
fitting. For proper flow, a minimum downward slope of 1” per 10’ run is required. (Note: If a proper downward angle is not possible, then it is recommended to use a Titan XG60 which in- cludes an integrated condensate pump or utilize an external condensate pump). -
Page 6: Indicator Lights
will hear one beep as the machine shuts down. Note that there is a one minute fan delay on shut- down. 11.2. Arrow Buttons • Use the up and down arrow buttons to set the desired humidity setpoint on the display screen. The setpoint can be any number between 35-90%. -
Page 7: Remote Control
••When the light glows red, it means the unit is in auto defrost mode and clearing the evaporator coil of any ice buildup. •4. Remote Indicator Light •• When the remote indicator light is green, it illustrates the unit is remote mode. •... -
Page 8: Operating Instructions
4. Water Drainage During normal operation, the Titan XG60 will automatically drain by the force of gravity. If you want to move or store your machine, wait at least 10 minutes to allow the machine to completely defrost, then lean unit gently towards drain to ensure that unit is completely drained. -
Page 9: Maintenance
Back View MERV 8 Filter Maintenance WARNING: Always unplug the unit before doing any maintenance. Cleaning the machine body Use a soft damp cloth to clean exterior of unit. Do not use any soap or solvents. Cleaning the filter Unplug the unit. 2. -
Page 10: Dehumidifier Storage
Dehumidifier Storage If the unit will be stored for an extended period of time, complete the following steps: 1. Turn off the unit and allow to dry 2. Manually drain pump reservoir 3. Wrap and secure the power cord 4. Cover filter mesh 5. -
Page 11: Troubleshooting
Flex Duct Installation Flex Duct Removal Rotate the flex duct counter- Rotate flex duct clockwise or clockwise or simply position remove wire tie and slide duct Troubleshooting Symptom Cause Solution Power Supply Verify that there is power to the outlet and that the plug is properly installed in outlet Room Temperature Over 105°... -
Page 12: Spare Parts
Titan XG60 Spare Parts Internal Components Internal Components Remote Control Remote Control T-606 Compressor Remote Control T-607 Compressor Capacitor T-100 Assembly (Includes T-101 and T-102) Temp/RH Sensor T-608 Cable T-101 Titan Remote Control T-609 Display Ribbon Cable Coil Temp Sensor... - Page 13 Warranty Seller warrants the equipment to be free from defects in workmanship and materials for a period of 12 months after shipment (60 months/5 years on compressor, evaporator and condenser). This war- ranty is limited, however, to the repair or replacement of defective equipment. If it is necessary to re- turn unit for service, customer is solely responsible for proper packaging and transportation costs.