Timer Recording; Note For Timer Recording & Otr - FUNAI DV220FX5 Owner's Manual

Timer Recording

Press first.
V S V V V V VHS VHS VHS VHS VHS
1
Press , Use
SETUP
"TIMER PROGRAMMING".
Then, press to go to next step.
2
Use / to select an
empty program number. Then,
press to go to next step.
3
Use / to select "ONCE",
"DAILY" (Mon-Fri), or "WEEKLY".
Then, press to go to next step.
4
Use / to select the
desired month. Then, press
to go to the next step.
Then, repeat procedures above to select the day,
start time, end time, and "L1" or "L2" as well.
5
Use / to select recording
speed. Then, press
the MENU.
To set another program after step
Then, repeat procedures from steps
5
.
You can program the unit to record up to 8
programs, and up to 1 year in advance.
6
Press to set the timer standby mode.
The [TIMER REC] indicator on this unit lights up
and the unit goes to the DVD mode.
Note: • To go back one step, press [0] during steps
• Select "L1" or "L2" to activate rear input jacks or
front input jacks accordingly.
EN
RECORDING
/ to select
- M E N U - TIMER PROGRAMMING
B TIMER PROGRAMMING
PROG.
SATELLITE LINK
DATE
AUTO REPEAT [OFF]
START TIME
CLOCK SET
END TIME
LANGUAGE SELECT
L1/L2
REC SPEED
Available program
number blinks.
PROGRAM NUMBER 1
DATE
START TIME – – : – –
END TIME – – : – –
L1/L2
REC SPEED – –
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 0 2 TUE
START TIME – – : – –
END TIME – – : – –
L1/L2
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
to remove
START TIME 0 7 : 3 0
END TIME 0 8 : 3 0
L1/L2
REC SPEED SP
B SP
5
, press
2
through
To Check, Correct or Cancel a Timer Program To Check, Correct or Cancel a Timer Program
[TIMER SET], and then press [VCR
remote control.
2) Repeat procedures in step 1 above.
3) Use [K / L] to select the program number you want
to check. The details of the program you select will
appear on the TV screen.
Use [0 / 1] to go to the digit you want to change.
Then, use [K / L] to enter the correct numbers.
12345678
You can cancel the entire program by pressing [0]
while the program number blinks.
4) Press [CLEAR] to exit.
5) Press [TIMER SET] to return to the timer standby
mode.
– – / – – To Cancel a Timer Recording in Progress To Cancel a Timer Recording in Progress
– –
– –
– – Press [C A] on the unit.
Note for Timer Recording & OTR
• If a power failure occurs or the cassette tape does not
have the erase-protection tab,
the [TIMER REC] indicator blinks and timer recording
cannot be performed.
• If there is a power failure occurred or the unit is
– –
unplugged for more than 30 seconds, clock setting and
– –
– –
all programmed timer recordings will be lost.
• If a cassette tape runs out before an OTR or a timer
recording is finished, the unit ejects the cassette tape.
After an OTR or a Timer Recording Has After an OTR or a Timer Recording Has
Been Set, This Unit Operates as Follows: Been Set, This Unit Operates as Follows:
1 0 / 0 2 TUE
• Press [TIMER SET] on the remote control or [C A] on
PM
PM
L1
the unit, then press [VCR
SLP function again.
• To cancel the timer standby mode, press [TIMER SET] on
.
the remote control or [C A] on the unit, then press
[VCR ] to activate the VCR function again.
When an OTR or a Timer Recording is Completed. When an OTR or a Timer Recording is Completed.
• If timer programs are left on the VCR, the unit will switch
to the DVD mode and then the VCR will go standby
for the next timer recording. (All the VCR functions will
be unavailable.) If auto power off has been in effect,
however, both DVD and VCR will go to standby mode.
• All the DVD functions are available while the VCR is in
OTR, Timer standby, or Timer Recording mode.
3 5
to .
• The [TIMER REC] indicator blinks if there are no more
timer programs.
• Press [C A] on this unit or [TIMER SET] on the remote
control to use the VCR when the unit is turned off.
To Use the DVD Player During Timer To Use the DVD Player During Timer
Recording or While the [TIMER REC] Recording or While the [TIMER REC]
Indicator is On or Blinking. Indicator is On or Blinking.
• Press [POWER y] to turn On the unit. Press [DVD ] on
the Remote Control to choose DVD mode. Then continue
with the other DVD features as described in this manual.
] on the
] to activate the VCR
21