Sony HCD-MG110 Service Manual

Sony HCD-MG110 Service Manual

Sony compact disc deck receiver service manual
Hide thumbs Also See for HCD-MG110:
Table of Contents

Advertisement

HCD-MG110/MG310AV
SERVICE MANUAL
Ver 1.0 2001.03
HCD-MG110/MG310AV are the Amplifier, CD player, Tape
Deck and Tuner section in MHC-MG110/MG310AV.
HC D-MG310AV only
This stereo system is equipped with the Dolby* Pro Logic
Surround decoder.
* Manufactured under license from Dolby Laboratories.
Dolby , Pro Logic , and the double-D symbol ; are
trademarks of Dolby Laboratories. Confidential
unpublished works. '1992-1997 Dolby Laboratories.
All rights reserved.
Amplifier section
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
with 8 ohm loads both channels driven, from
100 – 10,000 Hz; rated 75 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 milliwatts to
rated output.
HCD-MG310AV
Front speaker:
Continuous RMS power output
75 + 75 watts
(8 ohms at 1 kHz,
10% THD)
Total harmonic distortion less than 0.09%
(8 ohms at 1 kHz,
40 watts)
Center speaker:
Continuous RMS power output
25 watts
(8 ohms at 1 kHz,
10% THD)
Rear speaker:
Continuous RMS power output
25 + 25 watts
(8 ohms at 1 kHz,
10% THD)
Sony Corporation
9-873-801-11
2001C0500-1
Audio Entertainment Group
C 2001.3
General Engineering Dept.
Photo: HCD-MG110
Model Name Using Similar Mechanism
CD Mechanism Type
CD
Section
Base Unit Name
Optical Pick-up Name
Model Name Using Similar Mechanism
TAPE
Section
Tape Transport Mechanism Type

SPECIFICATIONS

HCD-MG110
Continuous RMS power output
75 + 75 watts
(8 ohms at 1 kHz,
10% THD)
Total harmonic distortion less than 0.09%
(8 ohms at 1 kHz,
40 watts)
Inputs
VIDEO/MD IN (phono jacks):
voltage 250 mV/450 mV,
impedance 47 kilohms
5.1CH (HCD-MG310AV only):
FRONT (phono jacks):
voltage 450 mV,
impedance 47 kilohms
REAR (phono jacks):
voltage 450 mV,
impedance 47 kilohms
CENTER (phono jack):
voltage 450 mV,
impedance 47 kilohms
SUB WOOFER (phono jack):
voltage 450 mV,
impedance 47 kilohms
Outputs
PHONES (stereo phone jack):
accepts headphones of
8 ohms or more
FRONT SPEAKER:
accepts impedance of 8 to
16 ohms (except for the
North American model)
COMPACT DISC DECK RECEIVER
US Model
NEW
CDM64-K1BD44A
BU-K1BD44A
KSM-213BFN
NEW
CM8L6Z511A
SURROUND SPEAKER REAR (HCD-MG310AV
only):
accepts impedance of 8 to
16 ohms (except for the
North American model)
SURROUND SPEAKER CENTER
(HCD-MG310AV only): accepts impedance of
8 ohms (except for the
North American model)
SUB WOOFER (HCD-MG310AV only):
voltage 1 V,
impedance 1 kilohm
CD player section
System
Compact disc and digital
audio system
Laser
Semiconductor laser
(λ = 780 nm)
Emission duration:
continuous
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Wavelength
780 – 790 nm
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
OPTICAL OUT (CD)
(Square optical connector jack, rear panel)
Wavelength
660 nm
Output Level
–18 dBm
– Continued on next page –

Advertisement

Table of Contents
loading

Summary of Contents for Sony HCD-MG110

  • Page 1: Specifications

    HCD-MG110/MG310AV SERVICE MANUAL US Model Ver 1.0 2001.03 HCD-MG110/MG310AV are the Amplifier, CD player, Tape Deck and Tuner section in MHC-MG110/MG310AV. Photo: HCD-MG110 HC D-MG310AV only Model Name Using Similar Mechanism This stereo system is equipped with the Dolby* Pro Logic Surround decoder.
  • Page 2: Table Of Contents

    Power requirements 120 V AC, 60 Hz (with the interval set at Frequency response 40 – 13,000 Hz (±3 dB), 10 kHz) using Sony TYPE I Power consumption 531 – 1,710 kHz cassette HCD-MG310AV: 200 watts (with the interval set at...
  • Page 3: Leakage Test

    LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
  • Page 4: Servicing Note

    HCD-MG110/MG310AV SECTION 1 SERVICING NOTE CD-TEXT TEST DISC This unit is able to display the test data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display. To check, perform the following procedure.
  • Page 5: General

    TIMER SELECT 3 (23, 27) FRONT* qd (25) * HCD-MG310AV only TIMER SET 3 (11, 23, 26) GAME e; (26, 29) ** HCD-MG110 only TUNER/BAND 5 (18) KEYBOARD INPUT jack ws VIDEO IN jack wl (29) (27) LINK* qg (25)
  • Page 6: Remote Control

    (stop) 0 . (go back) 0 m (rewind) 0 M (fast forward) 0 > (go forward) 0 TDISC/DISCt qs qj For HCD-MG110 1 2 3 4 CD wf (14, 21) CLOCK/TIMER SELECT 2 (23, 27) CLOCK/TIMER SET 3 (23, 26)
  • Page 7: Disassembly

    HCD-MG110/MG310AV SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW 3-2. UPPER COVER (Page 8) 3-3. FRONT BLOCK ASSY (Page 8) 3-4. MAIN BOARD 3-13. CASSETTE LID ASSY (A)/(B) (Page 9) (Page 13) 3-5.
  • Page 8: Upper Cover

    HCD-MG110/MG310AV Note: Follow the disassembly procedure in the numerical order given. 3-2. UPPER COVER 2 five screws 3 upper cover (BVTP3 × 8) 2 two screws (BVTP3 × 8) 1 three screws (BVTP3 × 8) 1 three screws (BVTP3 × 8) 3-3.
  • Page 9: Main Board

    HCD-MG110/MG310AV 3-4. MAIN BOARD MG310AV 3 three screws MG110 (BVTP3 × 8) 3 screw (BVTP3 × 8) 3 screw (BVTP3 × 8) MG310AV 3 three screws (BVTP3 × 8) 1 wire (flat type) (CN303) 2 three connectors (CN304, 314, 903)
  • Page 10: Main Amp Board", "Power Board

    HCD-MG110/MG310AV 3-6. “MAIN AMP BOARD”, “POWER BOARD” 2 four screws (BVTP3 × 8) 1 connector (CN502) 4 three screws 3 MAIN AMP board (BVTP3 × 8) 2 two screws (BVTP3 × 8) 5 center bracket 7 POWER board 6 two screws (BVTP4 ×...
  • Page 11: Mechanism Deck (Cdm64-K1Bd44A)

    HCD-MG110/MG310AV 3-8. MECHANISM DECK (CDM64-K1BD44A) 5 mechanism deck (CDM64-K1BD44A) 1 screw (2.6 × 8) 2 table (60) 4 two screws (BVTP3 × 8) lower chassis 3 screw (PSW3 × 6) 4 four screws 4 four screws (BVTP3 × 8) (BVTP3 × 8) 3-9.
  • Page 12: Bu Holder Assy

    HCD-MG110/MG310AV 3-10. BU HOLDER ASSY 1 tension spring (F1) 2 tension spring (F-2) 3 two screws (PTP2.6 × 8) 4 BU holder assy 3 two screws (PTP2.6 × 8) 3-11. “MOTOR GEAR ASSY (SLED) (M102)”, “CD BOARD” 7 gear 8 claw...
  • Page 13: Op Base Assy (Ksm-213Bfn)

    HCD-MG110/MG310AV 3-12. OP BASE ASSY (KSM-213BFN) 3 Remove the optical pick-up (KSM-213BFN) in the direction of arrow B . 2 sled shaft 1 Slide the lever in the direction of arrow A . 3-13. CASSETTE LID ASSY (A) / (B) 1 Open the cassette lid assy (A)/(B).
  • Page 14: Mech Deck

    HCD-MG110/MG310AV 3-14. MECH DECK 1 three screws (BVTP3 × 10) qs mech deck 0 two screws (BVTP2.6) qa MD bracket 4 cassette holder assy (A) 2 two screws (BVTP3 × 10) 9 TC board 5 cassette 8 screw (BVTP2.6) holder...
  • Page 15: Mechanical Adjustments

    HCD-MG110/MG310AV SECTION 4 MECHANICAL ADJUSTMENTS • TAPE MECHANISM DECK SECTION Torque Measurement Precaution Mode Torque meter Meter reading 1. Clean the following parts with a denatured alcohol-moistened 2.94 mN • m to 7.84 mN • m swab: CQ-102C 31 to 71 g • cm...
  • Page 16 HCD-MG110/MG310AV MEMO...
  • Page 17: Diagrams

    HCD-MG110/MG310AV SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM – CD SERVO Section – FILTER DIGITAL SIGNAL PROCESSOR, DIGITAL FILTER, D/A CONVERTER IC101 (1/2) RF AMP, 56 53 FOCUS/TRACKING ERROR AMP IC103 DETECTOR CD +5V PCMD LRCK INTERFACE C2PO RFAC RFAC RFAC...
  • Page 18: Block Diagram - Tuner/Tape Deck Section

    HCD-MG110/MG310AV 5-2. BLOCK DIAGRAM – TUNER/TAPE DECK Section – TUNER PACK TUNER L-CH (Page 19) FM ANT L-CH FM 75Ω ANT GND R-CH R-CH AM ANT ANT GND TU-CLK (HCD-MG310AV) TU-CE TUNED (HCD-MG310AV) TUNED 5.1CH (Page 19) INPUT SELECT SWITCH...
  • Page 19: Block Diagram - Surround Section

    HCD-MG110/MG310AV 5-3. BLOCK DIAGRAM – SURROUND Section – (HCD-MG310AV) LOW-PASS FILTER IC304 (1/2) SPE ANA (Page 21) (HCD-MG110) R-CH DOLBY PRO LOGIC SURROUND PROCESSOR R-CH IC301 L-CH (Page 18) WOOFER SWIN SWVOL J303 TRIMMER, SWVOL OUT SUPER WOOFER VOLUME IC304 (2/2)
  • Page 20: Block Diagram - Amp Section

    HCD-MG110/MG310AV 5-4. BLOCK DIAGRAM – AMP Section – J503 PHONE (HCD-MG310AV) J501 (1/2) FRONT L-CH DBFB AMP (Page 19) IC303 POWER AMP – FRONT SPEAKER IC501 IMPEDANCE R-CH USE 8Ω SURROUND – RY501 IC308 MUTING MUTING OVER LOAD DBFB DBFB LEVEL...
  • Page 21: Block Diagram - Display/Power Supply Section

    HCD-MG110/MG310AV 5-5. BLOCK DIAGRAM – DISPLAY/POWER SUPPLY Section – (HCD-MG310AV) GRID DRIVE LED DRIVE D703 – 707 Q721 – 723 Q713 – 717 LED DRIVE D708, 736, FL701 Q702 – 705, 718 D781, 782, 791 FLUORESCENT INDICATOR TUBE S701, 741 – 745,...
  • Page 22: Note For Printed Wiring Boards And Schematic Diagrams

    HCD-MG110/MG310AV 5-6. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • Circuit Boards Location (In addition to this, the necessary note is printed in each block) Note on Schematic Diagram: Note on Printed Wiring Boards: • All capacitors are in µF unless otherwise noted. pF: µµF •...
  • Page 23 HCD-MG110/MG310AV • IC Block Diagrams IC103 CXA2581N-T4 – CD Board – RW/ROM IC101 CXD3017Q DC OFST RFDCI – – RFDCO ERROR DIGITAL CORRECTOR DIGITAL ASYMMETRY CORRECTOR – RW/ROM VOFST OPERATIONAL LRCK AMPLIFIER ANALOG SWITCH PCMD INTERFACE DEMODULATOR CONVERTER EMPH APC AMP...
  • Page 24: Schematic Diagram - Cd Section

    HCD-MG110/MG310AV 5-7. SCHEMATIC DIAGRAM – CD Section – • • See page 35 for Waveforms. See page 23 for IC Block Diagrams. (Page 32) • Voltages and waveforms are dc with respect to ground The components identified by mark 0 or dotted under no-signal conditions.
  • Page 25: Printed Wiring Board - Cd Section

    HCD-MG110/MG310AV 5-8. PRINTED WIRING BOARD – CD Section – • See page 22 for Circuit Boards Location. OPTICAL PICK-UP BLOCK KSM-213BFN CD BOARD M101 (SPINDLE) S101 (LIMIT) (VC) M102 (SLED) TP (RFAC) TP (FE) MAIN BOARD TP (TE) CN303 (Page 34)
  • Page 26: Printed Wiring Boards - Cd Motor/Sensor Section

    HCD-MG110/MG310AV 5-9. PRINTED WIRING BOARDS – CD MOTOR/SENSOR Section – • See page 22 for Circuit Boards Location. (Page 34) MAIN BOARD CN305 T SENSOR BOARD L. T MOTOR BOARD 1 2 3 4 5 (LOADING) (TABLE) (11) 1-680-797- 4 3 2 1...
  • Page 27: Schematic Diagram - Cd Motor/Sensor Section

    HCD-MG110/MG310AV 5-10. SCHEMATIC DIAGRAM – CD MOTOR/SENSOR Section – (Page 32) (Page 32) (Page 32) (Page 32) (Page 32) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : CD...
  • Page 28: Printed Wiring Board - Tc Section

    HCD-MG110/MG310AV 5-11. PRINTED WIRING BOARD – TC Section – • See page 22 for Circuit Boards Location. MAIN BOARD (Page 34) CN311 TC BOARD 1-680-807- (11) HP101 PB HEAD (DECK A) HRPE101 REC/PB/ERASE HEAD (DECK B) • Semiconductor Location Ref. No.
  • Page 29: Schematic Diagram - Tc Section

    HCD-MG110/MG310AV 5-12. SCHEMATIC DIAGRAM – TC Section – • See page 35 for IC Block Diagram. (Page 30) • Voltages and waveforms are dc with respect to ground under no-signal conditions. no mark : TAPE PLAY ) : REC...
  • Page 30: Schematic Diagram - Main Section (1/4)

    HCD-MG110/MG310AV 5-13. SCHEMATIC DIAGRAM – MAIN Section (1/4) – (Page 37) (Page (Page 29) (Page 32) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 31: Schematic Diagram - Main Section (2/4)

    HCD-MG110/MG310AV 5-14. SCHEMATIC DIAGRAM – MAIN Section (2/4) – (Page 39) (Page 30) (Page 43) (Page 37) (Page 32) (Page 33) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 32: Schematic Diagram - Main Section (3/4)

    HCD-MG110/MG310AV 5-15. SCHEMATIC DIAGRAM – MAIN Section (3/4) – • See page 35 for IC Block Diagram. (Page 30) (Page 31) (Page 39) (Page 24) (Page (Page 27) (Page 27) (Page 27) (Page 27) (Page 27) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 33: Schematic Diagram - Main Section (4/4)

    HCD-MG110/MG310AV 5-16. SCHEMATIC DIAGRAM – MAIN Section (4/4) – • See page 35 for Waveforms. (Page 31) (Page 37) (Page 32) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM ) : CD PLAY ] : TAPE PLAY ∗...
  • Page 34: Printed Wiring Board - Main Section

    HCD-MG110/MG310AV 5-17. PRINTED WIRING BOARD – MAIN Section – • See page 22 for Circuit Boards Location. (Page 38) (Page 28) (Page 38) TAPE GAME LINK MECHANISM DECK DISPLAY BOARD TC BOARD BLOCK BOARD CN701 CN401 MAIN BOARD CNP702 (MG310AV)
  • Page 35 HCD-MG110/MG310AV • Waveforms – TC Board – – MAIN Board – – CD Board – IC401 TA8189N 1 IC103 qg (RFAC) (CD Play Mode) 4 IC101 ra (TE) (CD Play Mode) qa IC801 qa (SUBXOUT) METAL TAPE A CH2/A CH2/B /TAPE B –...
  • Page 36: Printed Wiring Boards - Amp Section

    HCD-MG110/MG310AV 5-18. PRINTED WIRING BOARDS – AMP Section – • See page 22 for Circuit Boards Location. • Semiconductor Location Ref. No. Location D501 D502 D504 D507 D508 PHONE D509 D510 E-11 D511 D512 D-11 D513 D-11 (Page 34) D601...
  • Page 37: Schematic Diagram - Amp Section

    HCD-MG110/MG310AV 5-19. SCHEMATIC DIAGRAM – AMP Section – (Page 33) (Page 30) (Page 43) (Page 43) (Page 31) • Voltages and waveforms are dc with respect to ground The components identified by mark 0 or dotted under no-signal (detuned) conditions.
  • Page 38: Printed Wiring Boards - Display Section

    HCD-MG110/MG310AV 5-20. PRINTED WIRING BOARDS – DISPLAY Section – • See page 22 for Circuit Boards Location. DISPLAY BOARD FL701 FLUORESCENT INDICATOR TUBE CNP707 X701 D707, S745 SURROUND CNP308 D706, S744 PRO LOGIC D705, S743 FRONT D704, S742 REAR CNP703...
  • Page 39: Schematic Diagram - Display Section

    HCD-MG110/MG310AV 5-21. SCHEMATIC DIAGRAM – DISPLAY Section – • • See page 35 for Waveform. See page 35 for IC Block Diagram. (Page 32) (Page 31) (Page 41) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions.
  • Page 40: Printed Wiring Board - Control Section

    HCD-MG110/MG310AV 5-22. PRINTED WIRING BOARD – CONTROL Section – • See page 22 for Circuit Boards Location. CONTROL BOARD TUNER/BAND TAPE A/B 5.1CH/VIDEO (MD) D736, S700 TIMER I / 1 SELECT SURROUND MODE D708, S751 PRESET EQ X PAUSE TIMER SET...
  • Page 41: Schematic Diagram - Control Section

    HCD-MG110/MG310AV 5-23. SCHEMATIC DIAGRAM – CONTROL Section – (Page 39) • Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : FM...
  • Page 42: Printed Wiring Boards - Power Section

    HCD-MG110/MG310AV 5-24. PRINTED WIRING BOARDS – POWER Section – • See page 22 for Circuit Boards Location. • Semiconductor Location Ref. No. Location D901 POWER BOARD (CHASSIS) D902 D911 D912 D913 D914 (AC IN) Q901 T902 POWER TRANSFORMER (SUB) T901...
  • Page 43: Schematic Diagram - Power Section

    HCD-MG110/MG310AV 5-25. SCHEMATIC DIAGRAM – POWER Section – (Page 37) (Page 37) (Page 31) • Voltages and waveforms are dc with respect to ground The components identified by mark 0 or dotted under no-signal (detuned) conditions. line with mark 0 are critical for safety.
  • Page 44: Ic Pin Function Description

    HCD-MG110/MG310AV 5-26. IC PIN FUNCTION DESCRIPTION • CD BOARD IC101 CXD3017Q (DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, DIGITAL FILTER, D/A CONVERTER) Pin No. Pin Name Description Pin No. Pin Name Description RFDC SQSO Subcode Q data output to the system controller (IC801)
  • Page 45 HCD-MG110/MG310AV • MAIN BOARD IC801 M30622MGA-A42FP (SYSTEM CONTROLLER) Pin No. Pin Name Description — Not used (open) LOAD POS Loading motor drive signal (load-out direction) output the motor driver (IC881) LOAD NEG Loading motor drive signal (load-in direction) output the motor driver (IC881)
  • Page 46 HCD-MG110/MG310AV Pin No. Pin Name Description POWER STBY Standby relay drive signal output terminal “L”: standby, “H”: power on FL RESET Reset signal output to the display controller (IC701) A-MUTE Audio muting on/off control signal output terminal “H”: muting HP-CHK Headphone detection signal input terminal “H”: headphone on...
  • Page 47 HCD-MG110/MG310AV Pin No. Pin Name Description C-SENS Internal status monitor input from the CXD3017Q (IC101) C-DATA Command serial data output to the CXD3017Q (IC101) C-LATCH Command latch pulse output to the CXD3017Q (IC101) C-CLK Command serial data transfer clock signal output to the CXD3017Q (IC101)
  • Page 48 HCD-MG110/MG310AV • DISPLAY BOARD IC701 MB90M407APF-G-104-BND (DISPLAY CONTROLLER) Pin No. Pin Name Description 1 to 10 G4 to G13 Grid drive signal output to the fluorescent indicator tube (FL701) VSS-IO — Ground terminal 12 to 22 S34 to S24 Segment drive signal output to the fluorescent indicator tube (FL701) VDD-FIP —...
  • Page 49 HCD-MG110/MG310AV Pin No. Pin Name Description LED6 LED drive signal output terminal (REAR) (MG310AV only) LED7 LED drive signal output terminal (LINK) (MG310AV only) LED8 LED drive signal output terminal (CD lid illumination) LED9 LED drive signal output terminal (CD)
  • Page 50: Exploded Views

    HCD-MG110/MG310AV SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark may have some difference from the original are seldom required for routine service.
  • Page 51: Front Panel Section

    HCD-MG110/MG310AV 6-2. FRONT PANEL SECTION not supplied not supplied S791 Supplied with RV701 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-232-761-01 CD LID (MG310AV) 4-232-757-01 CATCHER, BRACKET 4-232-761-21 CD LID (MG110) 3-029-159-02 SPRING, PUSH CATCHER RETURN...
  • Page 52: Chassis Section

    HCD-MG110/MG310AV 6-3. CHASSIS SECTION CDM64-K1BD44A not supplied not supplied not supplied supplied not supplied not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No.
  • Page 53: Mechanism Deck Section (Cdm64-K1Bd44A)

    HCD-MG110/MG310AV 6-4. MECHANISM DECK SECTION (CDM64-K1BD44A) BU-K1BD44A not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-680-799-11 D SENSOR (IN) BOARD 4-216-085-01 SPRING (F-1), TENSION 4-231-310-01 SLIDER (60) 4-216-086-01 SPRING (F-2), TENSION 4-216-088-02 GUIDE (DISC) 4-957-577-21 SCREW PTP WH (2.6X8) (DIA.
  • Page 54: Base Unit Section (Bu-K1Bd44A)

    HCD-MG110/MG310AV 6-5. BASE UNIT SECTION (BU-K1BD44A) not supplied M101 M102 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No.
  • Page 55: Electrical Parts List

    HCD-MG110/MG310AV SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
  • Page 56 HCD-MG110/MG310AV CD LED CONTROL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R107 1-216-833-11 METAL CHIP 1/16W < RESISTOR > R108 1-216-827-11 METAL CHIP 3.3K 1/16W R109 1-216-857-11 METAL CHIP 1/16W R781 1-216-805-11 METAL CHIP 1/16W...
  • Page 57 HCD-MG110/MG310AV CONTROL D SENSOR (IN) D SENSOR (OUT) DISPLAY Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S762 1-762-196-21 SWITCH, TACT (m) C742 1-126-964-11 ELECT 10uF S763 1-762-196-21 SWITCH, TACT (M) C743 1-126-964-11 ELECT 10uF S764...
  • Page 58 HCD-MG110/MG310AV DISPLAY DOOR LED FUSE GAME LINK Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R705 1-216-845-11 METAL CHIP 100K 1/16W < ROTARY ENCODER > R706 1-216-809-11 METAL CHIP 1/16W RV702 1-476-597-11 ENCODER (ROTARY TYPE) (DISC ACCESS)
  • Page 59 HCD-MG110/MG310AV L.T MOTOR LOAD SW MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C145 1-126-961-11 ELECT 2.2uF 1-680-797-11 L.T MOTOR BOARD C150 1-126-963-11 ELECT 4.7uF (MG110) **************** C172 1-126-961-11 ELECT 2.2uF (MG310AV) ************************************************************** C176 1-162-927-11 CERAMIC CHIP...
  • Page 60 HCD-MG110/MG310AV MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C303 1-107-826-11 CERAMIC CHIP 0.1uF C334 1-136-157-00 FILM 0.022uF (MG310AV) (MG310AV) C304 1-126-964-11 ELECT 10uF C335 1-136-157-00 FILM 0.022uF (MG310AV) (MG310AV) C305 1-126-964-11 ELECT 10uF C336 1-107-826-11 CERAMIC CHIP 0.1uF...
  • Page 61 HCD-MG110/MG310AV MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C374 1-162-970-11 CERAMIC CHIP 0.01uF < DIODE > (MG310AV) C375 1-107-826-11 CERAMIC CHIP 0.1uF D350 8-719-921-63 DIODE MTZJ-T-77-7.5B D389 8-719-991-33 DIODE 1SS133T-77 C376 1-126-960-11 ELECT D395...
  • Page 62 HCD-MG110/MG310AV MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R110 1-216-835-11 METAL CHIP 1/16W < TRANSISTOR > (MG310AV) Q101 8-729-036-89 TRANSISTOR KTC3198GR-A R111 1-216-835-11 METAL CHIP 1/16W Q102 8-729-036-89 TRANSISTOR KTC3198GR-A (MG310AV) Q112 8-729-036-89 TRANSISTOR...
  • Page 63 HCD-MG110/MG310AV MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R214 1-216-833-11 METAL CHIP 1/16W R215 1-216-845-11 METAL CHIP 100K 1/16W R319 1-216-845-11 METAL CHIP 100K 1/16W (MG310AV) R321 1-216-827-11 METAL CHIP 3.3K 1/16W R216 1-216-845-11 METAL CHIP...
  • Page 64 HCD-MG110/MG310AV MAIN MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R971 1-216-813-11 METAL CHIP 1/16W R384 1-216-845-11 METAL CHIP 100K 1/16W R972 1-216-813-11 METAL CHIP 1/16W R385 1-216-845-11 METAL CHIP 100K 1/16W R973 1-216-833-11 METAL CHIP...
  • Page 65 HCD-MG110/MG310AV MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C602 1-126-961-11 ELECT 2.2uF IC602 8-749-017-97 IC STK402-240 (MG310AV) (MG310AV) C603 1-162-962-11 CERAMIC CHIP 470PF < TERMINAL > (MG310AV) C604 1-162-962-11 CERAMIC CHIP 470PF J501...
  • Page 66 HCD-MG110/MG310AV MAIN AMP Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R513 1-216-841-11 METAL CHIP 1/16W R607 1-216-821-11 METAL CHIP 1/16W (MG310AV) (MG310AV) R514 1-216-841-11 METAL CHIP 1/16W R608 1-216-821-11 METAL CHIP 1/16W (MG310AV) (MG310AV) R515...
  • Page 67 HCD-MG110/MG310AV MAIN AMP POWER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R640 1-216-821-11 METAL CHIP 1/16W < RELAY > (MG310AV) 0 RY901 1-755-332-11 RELAY 0 R642 1-233-352-41 ENCAPSULATED COMPONENT 0.22 (MG310AV) < TRANSFORMER > R643...
  • Page 68 HCD-MG110/MG310AV T SENSOR Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C442 1-162-927-11 CERAMIC CHIP 100PF R436 1-216-797-11 METAL CHIP 1/16W C443 1-162-927-11 CERAMIC CHIP 100PF R437 1-216-829-11 METAL CHIP 4.7K 1/16W R438 1-216-841-11 METAL CHIP...
  • Page 69 HCD-MG110/MG310AV MEMO...
  • Page 70: Revision History

    HCD-MG110/MG310AV REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

This manual is also suitable for:

Hcd-mg310av

Table of Contents