Table of Contents
Advertisement
WALRB4P manual booklet
CHANGING VOLUME LOCK
The One For All 4 Device Universal Remote Control is set at the factory for
independent volume control of each selected device. However, you may
change the Volume Lock setting to Global Volume Lock so that a device's vol-
ume will be locked to one mode (e.g., to control TV volume in all other
modes).After that, if desired, you can perform Individual Volume Unlock on a
selected device to set its volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1.
Press and hold
then release
SET
2.
Enter
-
-
and then press any mode key once (e.g.,
9
9
3
The
will blink twice.
LED
3.
Now, when you press
the selected device (e.g.,
of the mode you have selected.
Unlocking Volume Control For A Single Device (Individual Volume
Unlock)
1.
After performing Global Volume Lock (above),press a desired
mode key where you want volume to be unlocked (e.g.,
) and controlled within its own mode.
DVD
2.
Press and and hold
then release
SET
3.
Enter
-
-
and then press
9
9
3
four times.
4.
If desired, repeat steps 1 through 3 (of this section) for
each device that you want volume to be unlocked.
5.
Now, after you select a device that has volume unlocked
(e.g.,
), pressing
DVD
device's volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting)
NOTE: Performing these instructions will restore independent volume control for all pro-
grammed devices (e.g., TV volume control in TV mode, VCR volume in VCR/PVR mode,
etc.).
1.
On the remote control, press and hold
light) blinks twice,then release
2.
Enter
-
-
and then press
9
9
3
blink four times.
5/2/06
3:16 PM
Page 13
until the
(red light) blinks twice,
SET
LED
.
,
, or
, the volume of
VOL +
VOL -
MUTE
) will be controlled, regardless
TV
until the
(red light) blinks twice,
SET
LED
.
once. The
will blink
VOL -
LED
,
, or
will control the
VOL +
VOL -
MUTE
until the
SET
LED
.
SET
once. The
will
VOL +
LED
13
3.
Volume will again be independently controlled according
to its default states for all programmed devices.
CLEARING CUSTOM PROGRAMMING
The One For All 4 Device Universal Remote Control contains an Operational
Feature Reset program.
If desired, you can use it to clear custom programming, except your setup
).
TV
codes and reassigned device keys, and reset them to original factory set-
tings.Also see Restoring Factory Default Settings as below.
IMPORTANT: Executing this program will erase all your custom settings for
Power Macro, Favorite Channels, and Volume Lock.
1.
Press and hold
then release
2.
Enter
will return to normal operation.
RESTORING FACTORY DEFAULT SETTINGS
The One For All 4 Device Universal Remote Control also contains a Factory
Reset program that you can use to reset all custom settings and setup codes
to original factory settings.Also see Clearing Custom Programming as above.
IMPORTANT: Executing this program will erase all your custom settings for
Power Macro, Favorite Channels, Volume Lock, Reassigned Devices, and all
device settings.
1.
Press and hold
then release
2.
Enter
will return to normal operation.
(red
until the
(red light) blinks twice,
SET
LED
.
SET
-
-
. The
will blink twice. The remote control
9
8
0
LED
until the
(red light) blinks twice,
SET
LED
.
SET
-
-
. The
will blink twice. The remote control
9
8
1
LED
14
Hide quick links:
Advertisement
Table of Contents
