Table of Contents
Advertisement
Remote Control
AVR Selector :
Press this button to use the
Mute : Press this button to momentarily
remote control for operation of the AVR-65. Note
silence the AVR-65 or TV set being controlled,
that the button will briefly turn red after it has
depending on which device has been selected.
been pressed to confirm your selection.
Test :
Press this button to begin the
Device Control Selectors :
Press one of
sequence used to calibrate the AVR-65's output
these button to use the remote to control the
levels.
functions of another audio/video device. Note
that the button will briefly turn red after it has
Display/Multiroom Button :
been pressed to confirm your selection.
does not function with AVR-65, but it is available
for use with other devices.
Power Button :
Press this button to turn the
currently selected device on or off.
Buttons :
buttons. They will be used most frequently to
select a surround mode.
To change the surround mode, first press the
SURR/CH
button
. Next press these
buttons to scroll up or down through the list of
surround modes that appear in the Information
Display
. These buttons are also used to
increase or decrease output levels used to lower
the AVR-65's output levels when configuring the
unit with either the internal test tone or and
external source. They are also used to enter
delay time settings after the
Delay
button
been pressed.
/
Channel Button :
This button is used
to start the process of setting the AVR-65's
output levels to an external source. Once this
button is pressed, use the
/
buttons
select the channel being adjusted, then press
the
Set
button
, followed by the
/
again to change the level setting.
Set Button :
This button is used to enter
settings into the AVR-65's memory. It is also
used in the setup procedures for delay time,
speaker configuration and channel output level
adjustment.
Night Mode :
Press this button to activate
the "Night" mode, preventing loud playback
when the digital modes are in use without
altering the dynamic range of the output signal.
When the AVR-65 remote is being programmed
to operate other devices, this button is pressed
to begin a readout of a programmed code.
Source Selectors :
Press these buttons to
select an input source for the AVR-65. The AM/
FM button is also used to switch between
frequency bands when the tuner in use.
This button
NOTE :
Pressing one of these buttons selects
the source only. In order to control the actual
source machine using the remote you must
These are multi purpose
press the
Press Control Selector
button
the desired product.
Numeric Keys :
These buttons serve as a
ten-button numeric key-pad to enter tuner preset
positions. They are also to be used to select
channel numbers when TV has been selected
on the remote, or to select track numbers on a
CD, DVD or LD player, depending on how the
remote has been programmed.
NOTE :
The 0 button has a dual function. It also
serves as the
CLEAR
button for use in
has
programming the tuner or clearing the system
memory.
Direct/Enter :
Press this button to select a
radio station by entering its frequency using the
Numeric Key
.
to
Memory Button :
Press this button to enter
buttons
a radio station into the AVR-65's preset memory.
After pressing the button the
MEMORY
indicator
will flash, and you then have five seconds to
enter a present memory location using the
Numeric Keys
.
NOTE :
Although the word "Sleep" appears
above this button, it refers to control of devices
other than the AVR-65. Use the
Sleep
button
to control the AVR-65's Sleep function.
OSD Button :
This button dose on screen
display function with the AVR-65.
Semi
Full
OFF
Light Button :
Press this button to activate
the remote's built-in back-light for better legibility
of the buttons in a darkened room.
Tuner Mode :
Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so that the
AUTO
indicator
goes out,
pressing the
Tuning
buttons
will move the
frequency up or down in single-step increments.
When the FM band is in use, pressing this button
for
when a station's signal is weak will change to
monaural reception, as indicated by the
MONO
- 7 -
indicator
.
to enter your choice.
Clear Button :
This button dose not
Speaker Configuration :
function with the AVR-65, but it is available for
to begin the process of configuring the AVR-65's
use with other devices.
Bass Management System for use with the type
of speaker used in your system.
Press Up/Down :
When the tuner is in use,
Once the button has been pressed, use the
these buttons scroll through the stations that
buttons
to select the channel you wish to set
have been programmed into the AVR-65's
up. Press the
Set
memory, When many source devices, such as
another channel to configure. When all
CD players, VCRs and cassette decks, are
adjustments have been completed, press the Set
selected using the
Device Control Selectors
.
button twice to exit the settings and return to
these buttons will normally function as chapter
normal operation.
step or track advance.
Surround Mode Selector :
Tuning Up/Down :
When the tuner is in use,
button to begin the process of changing the
these buttons will tune up or down through the
surround mode. After the button has been
selected frequency band. If the
Tuner Mode
pressed, use the
button
has been pressed so that the
AUTO
desired surround mode. Note that this button is
indicator
is illuminated, pressing these
also used in the "Auto Search" process.
buttons will cause the tuner to seek the next
station with acceptable signal strength for quality
Volume :
Press these buttons to raise or
reception. When the
AUTO
indicator
is NOT
lower the system volume.
illuminated, pressing these buttons will tune
stations in single-step increments.
Sleep Button :
the unit in the Sleep Mode. After the time shown
Transport Control :
These controls do not
in the display, the AVR-65 will automatically go
control any function of the AVR-65, but they are
into the standby mode. Each press of the button
used extensively when operating a wide variety
changes the time until turn-off in the following
of CD players, cassette decks and VCRs.
order:
Delay/Prev Ch. :
Press this button to begin
90
80
the process for setting the delay times used by
the AVR-65 when processing surround sound.
30
20
After pressing this button the delay times are
entered by pressing the
Set
button
, and then
using
/
buttons
to change the setting.
Note that this button is also used to change
Press the Set button again to complete the
channels on your TV when the TV is selected
process.
using the Devise Control Selector
/
Digital Button :
This button is used to
When the AVR-65 remote is being programmed
select the type of digital input used with any one
for the codes of another device, this button is
of the input sources connected to the AVR-65.
also used in the "Auto Search" process.
After pressing this button, use the
/
buttons
(7) to make your selection between
OPTICA
or
COAXIAL
digital. Press the
Set
button
Press this button
/
button
, and then select
Press this
/
buttons
to select the
Press this button to place
70
60
50
40
10
5
1
OFF
.
Hide quick links:
Advertisement
Table of Contents
