http://www.xiaoyu163.com SAFETY INFORMATION 3 7 63 1515 0 CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual.
Page 3
http://www.xiaoyu163.com 3 7 63 1515 0 [Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
http://www.xiaoyu163.com 1. SERVICE PRECAUTIONS 3 7 63 1515 0 1.1 SERVICE PRECAUTIONS 1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2.
http://www.xiaoyu163.com 1.2 NOTES ON SOLDERING 3 7 63 1515 0 For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs accompanied by reworking of soldering.
http://www.xiaoyu163.com 2. SPECIFICATIONS 3 7 63 1515 0 2.1 SPECIFICATIONS AVH-P3200BT/XNUC, AVH-P3200DVD/XNUC General Equalizer (8-Band Graphic Equalizer): Frequency......40/80/200/400/1k/2.5k/8k/ Power source......14.4 V DC (10.8 V to 15.1 V 10k Hz allowable) Gain ........±12 dB Grounding system....Negative type HPF: Maximum current consumption Frequency......
Page 9
http://www.xiaoyu163.com 3 7 63 1515 0 AVH-P3250BT/XNRD, AVH-P3250DVD/XNRC, AVH-P3250DVD/XNRD, AVH-P3250DVD/XNRI General DVD Player Rated power source....14.4 V DC System .........DVD video, Video CD, CD, (allowable voltage range: WMA, MP3, AAC, DivX, 12.0 V to 14.4 V DC) JPEG system Grounding system....Negative type Usable discs ......DVD video, Video CD, CD, Maximum current consumption CD-R/RW, DVD-R/RW/RDL...
(BT model only) The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Pioneer Corporation is under license. Other trademarks and trade names are those of their respective owners. u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
3 7 63 1515 0 Head unit CAUTION • Use an optional Pioneer USB cable (CD-U50E) to connect the USB audio player/USB mem- ory as any device connected directly to the unit will protrude out from the unit and may...
http://www.xiaoyu163.com 3 7 63 1515 0 AVH-P3250BT/XNRD, AVH-P3250DVD/XNRC, AVH-P3250DVD/XNRD, AVH-P3250DVD/XNRI Remote control Part Operation Press to select the tuner band when tuner is selected as a source. Also used to cancel the control mode of functions. Press to switch be- BAND/ESC tween modes when playing discs with...
http://www.xiaoyu163.com 3. BASIC ITEMS FOR SERVICE 3 7 63 1515 0 3.1 CHECK POINTS AFTER SERVICING To keep the product quality after servicing, please confirm following check points. Procedures Item to be confirmed Confirm whether the customer complain has The customer complain must not be been solved.
http://www.xiaoyu163.com 3.2 PCB LOCATIONS 3 7 63 1515 0 DVD Core Unit Connect PCB SD PCB Interface PCB BT ANT PCB Keyboard PCB Mother Unit Monitor PCB L 13942296513 P:AVH-P3200BT/XNUC Q:AVH-P3250BT/XNRD J:AVH-P3200DVD/XNUC K:AVH-P3250DVD/XNRC L:AVH-P3250DVD/XNRD M:AVH-P3250DVD/XNRI Unit Number Unit Number Unit Number Unit Number Unit Number Unit Number...
http://www.xiaoyu163.com 3.3 JIGS LIST 3 7 63 1515 0 Disc TDV-582 Skew adjustment, Check points after servicing, Inspection method of Pickup Unit Disc TCD-782 Inspection method of Pickup Unit GGF1539 Disconnect the Cord Assy of the BT ANT PCB - Grease List Name Jig No.
http://www.xiaoyu163.com 4. BLOCK DIAGRAM 3 7 63 1515 0 Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". IP BUS model P : AVH-P3200BT/XNUC Q : AVH-P3250BT/XNRD JA2504 JA2503 CKS3414-A YKS5001-E J : AVH-P3200DVD/XNUC...
Page 25
http://www.xiaoyu163.com 3 7 63 1515 0 IP BUS NAVI INTERFACE CN2502 JA2504 JA2502 JA2501 CKS4497-A CKS3414-A CKN1018-A CKB1065-A INTERFACE PCB CN2501 CKS6062-A FRONT OUT FM/AM RCA V IN OUT REAR OUT CN521 CKS6051-A JA402 CKX1070-A JA561 JA562 CKB1085-A XKB7001-B MOTHER UNIT(AUDIO) L 13942296513 MOTHER UNIT(SYSTEM) MOTHER UNIT(POWER SUPPLY)
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 MOTHER UNIT (1/2) CN751 SPDIFSENS K L M Q ONLY Q581 SPDIFOUT IECOUT SPDIF IC581 TC7SET08FUS1 LS_L ANALOG_LOUT BUSL+ Q751 IN4L+ Q752 BUSL- SYS+B IN4L- AV_LOUT IN2L BT_TEL IN3L ONSEI+ CN1901 IN5L ONSEI- STANBY STNBY IN5G LS1−>SRX...
http://www.xiaoyu163.com 5.2 INSPECTION METHOD OF PICKUP UNIT 3 7 63 1515 0 Disc to be used CD-DA: TCD-782 DVD-Video: TDV-582 Execution method Replace the PICK UP START SKEW ADJ. LD turned on? Check parts Check point: Check point: RF level check LD current check AS MAX check LD current check...
Page 36
http://www.xiaoyu163.com 3 7 63 1515 0 LD current check Check Status: [Foucs closed] of TEST MODE Disc Check Point Threshold Remarks: LD current GGV1025 DVDLD1-VCC5_3 60 - 390 (mV) 10 - 65 (mA) Expansion NO. Disc Check Point Threshold Remarks: LD current TCD-782 CDLD1-VCC5_3 60 - 360 (mV)
Page 37
http://www.xiaoyu163.com 3 7 63 1515 0 ASMAX check ASMAX value shows the value of RF level. Status: [Foucs closed] of TEST MODE Disc Check Point Threshold Remarks: 8 digits value of Only four last digits are more than GGV1025 ASMAX displayed according to on display 0000 0B00...
Page 39
http://www.xiaoyu163.com Check 1: Standby OK? 3 7 63 1515 0 <Check> Check the voltage at the “STANBY” test point while the power is on. Use the “DGND1” test point at the reference. Specification value Check point Module No. Unit VCC33 V- STANBY-DGND1 0.6 V or more Side A...
Page 40
http://www.xiaoyu163.com Check 2: Is VDD5 (VCC33, VCC12) power supply voltage OK? 3 7 63 1515 0 IC1401 FLASH power supply (Data) VCC33 (= 3.3 V) IC1402 FLASH power supply (Program) IC1004 IC1481 SDRAM power supply 3.3 V output regulator IC1501 DV5U power supply IC1005 VCC12 (= 1.2 V) IC1501 DV5U power supply...
Page 41
http://www.xiaoyu163.com 3 7 63 1515 0 Check 3: Reset OK? <Check> Check the voltage at the “XRES” test point while the power is on. Use the “DGND1” test point at the reference. Check point Module No. Specification value Unit 1 XRES-DGND1 VCC33 ×...
Page 42
http://www.xiaoyu163.com Check 4: Is VSENS OK? 3 7 63 1515 0 CN1901 HOST I/F IC1501 R1004, DV5U R1007 IC1004 Regulator IC1005 VCC12 DC/DC converter STANBY XRES Fig 4.1: Power supply configuration and VSENS <Check> Check the voltage at the “VSENS” test point while the power is on. Use the “DGND1”...
Page 43
http://www.xiaoyu163.com Check 5: 27 MHz Normal? 3 7 63 1515 0 <Outline> Each clock is created inside the IC1501 using the 27 MHz master crystal oscillator (X1501). IC1501 DVD-LSI OSCO X1501 27 MHz OSCI crystal VCC33 VCC12 Fig 5.1: Clock configuration <Check method>...
Page 44
http://www.xiaoyu163.com Check 6: Is SDRAM I/F OK? 3 7 63 1515 0 <Outline> In order to secure the MPEG stream data as the buffer, the capacity of communication I/F SDRAM between the LSI and the memory is 64Mbit. Be careful as XCSM, XWE, XCAS and XRAS of IC1480 are called differently in IC1501, namely NCSM, NWE, NCAS, NRAS.
Page 45
http://www.xiaoyu163.com <Check> Check the conductivity at “check point 1” and “check point 2” without power. 3 7 63 1515 0 In case of NG, check the soldering and defective components throughout the “output t input” of the applicable section. Signal name Check point 1 Check point 2 Specification value...
Page 46
http://www.xiaoyu163.com Side B 3 7 63 1515 0 Check point 1 (IC1480) Side A L 13942296513 Check point 2 (IC1501) Fig 6.2: SDRAM I/F check point u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 47
http://www.xiaoyu163.com Check 7: Is VD8, VCC5 power supply voltage OK? 3 7 63 1515 0 VD8_1 F.E. driver system IC1002 VCC5 (= 5.0 V) VD8_2 Power supply REG IC for PU for VCC 5 V. Fig 7.1: Power supply configuration <Check>...
Page 48
http://www.xiaoyu163.com Check 8: Is AVCC5 voltage OK? 3 7 63 1515 0 IC1003 AVCC5 (= 5.0 V) IC1801 REG IC Audio-DAC for AVCC 5 V. Fig 8.1: Power supply configuration <Check> Playback DVD-REF-A1 TITLE 1 and check the voltage at the stylus. Check with PGND and GNDAU being the reference.
Page 49
http://www.xiaoyu163.com 3 7 63 1515 0 Check 9: Is DACCLK normal? <Outline> DACCLK for Audio-DAC is created by IC1501 using the 27 MHz master crystal oscillator (X1501). IC1501 X1501 DVD-LSI IC1801 DACCLK Audio-DAC 27 MHz crystal VCC33 VCC12 Fig 9.1: Clock configuration <Check method>...
Page 50
http://www.xiaoyu163.com Side B 3 7 63 1515 0 Check point 1 (DACCK stylus) Side A L 13942296513 Check point 2 (IC1501 148 pin) DGND2 Fig 9.3: 27 MHz, DACCLK check point u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 51
http://www.xiaoyu163.com Check 10: Is the audio circuit OK? 3 7 63 1515 0 <Outline> The serial 3 lines digital output + DACCLK, output from DVD-LSI (IC1501), are converted to analog audio signal at Audio-DAC (IC1801) and are output from the HOST I/F (CN1901). Simultaneously, the analog MUTE signal is also output from DVD-LSI (IC1501) via the HOST I/F.
Page 52
http://www.xiaoyu163.com 3 7 63 1515 0 Side A DGND2 ADOUT LRCK Side B L 13942296513 SRCK Fig 10.3: Serial 3 lines check points u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 53
http://www.xiaoyu163.com 3 7 63 1515 0 The following checks shall be conducted using the following measurement circuits with GNDAU1 being the reference. 47 kohm 47 kohm GNDAU1 Check point 1 (stylus) Specification value (rms) Reference waveform 1 400 ± 150 mV Waveform 4 1 400 ±...
Page 54
http://www.xiaoyu163.com Side A 3 7 63 1515 0 IEC DGND2 Fig 10.6: Digital audio signal (IECOUT) check point L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 55
http://www.xiaoyu163.com Check 11: Is the video circuit OK? 3 7 63 1515 0 <Outline> Composite signal and component signal are output from DVD-LSI (IC1501), and are output from the HOST I/F (CN1901) via a buffer circuit. CN1901 HOST I/F IC1501 DVD_LSI Composite COMPOSITE...
Page 56
http://www.xiaoyu163.com Side A 3 7 63 1515 0 COMPOSITE GNDV Fig 11.3: VIDEO signal check point L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 57
http://www.xiaoyu163.com 3 7 63 1515 0 Check 12:How to judge whether the flash memory has reached its life or not. If the reaction to user operation is slow or operation is slow in general, there is a possibility that the flash memory has reached its life.
Page 58
http://www.xiaoyu163.com Check 13: 48 MHz Normal? 3 7 63 1515 0 <Outline> Each clock is created inside the IC1501 using the 48 MHz master crystal oscillator (X1501). IC1501 DVD-LSI X1950 48 MHz crystal USB_CLOCK VCC33 VCC12 Fig 13.1: Clock configuration <Check method>...
Page 59
http://www.xiaoyu163.com Side A 3 7 63 1515 0 IC1501 50pin DGND1 Fig 13.3: 48 MHz check point L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 60
1.USB Memory: Play a song from USB memory and check D+ and D- with the DGND standards. 2.iPod: Connect iPod and check CP_RESET, SDA and SCL with the DGND standards until the pioneer log appears. Play a song from iPod and check D+/D- with the DGND standards.
Page 61
http://www.xiaoyu163.com Side A 3 7 63 1515 0 SDATA CP_ RESET SCLOCK DGND2 L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 5.4 ERROR CODE LIST 3 7 63 1515 0 Generation source Method of reset UART Source Eject Play Key Error status OSD *1 Meaning Disc (MSC) (iPod) Off/On Off/On A disc containing the unplayable NON-PLAYABLE DISC Format only USB device that doesn't correspond INCOMPATIBLE DEVICE USB device of format alone that UNPLAYABLE FILE...
Page 66
http://www.xiaoyu163.com 3 7 63 1515 0 X: Cancel the error by operation. -: Error is not cancelled by operation. *: No setting *1 A content displayed on OSD. As for the items having multiple display patterns, the upper row is for the Japanese version Full GUI, and the lower row is for the Touch Panel model and Full GUI (English version).
http://www.xiaoyu163.com 6. SERVICE MODE 3 7 63 1515 0 6.1 MONITOR TEST MODE [Method for Mode IN] When the reset start is done while pushing REVERSE and EJECT, it shifts to the monitor test mode. [Display specifications] [Operation specification] Operational description Remote controller key Selection cursor up movement Selection cursor down movement...
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 2. Touch Panel Test [How to activate the touch panel test mode] Choose "Touch Panel Test" among the monitor test mode menu screen. [Menu types in the mode] The calibration test mode consists of the following menus. Top menu Outermost circumference inspection Calibration inspection...
Page 72
http://www.xiaoyu163.com 3 7 63 1515 0 [Outermost circumference inspection] [Outline] Outermost circumference value of X and Y is obtained by tracing the outermost circumference of the touch panel screen. When exiting the menu screen by pressing 5 key, the captured value is stored in the EEPROM. Furthermore, when storing the value, checking is made as to whether the value is within the range or not.
Page 73
http://www.xiaoyu163.com 3 7 63 1515 0 [16 points adjustment] [Outline] When correctly touched, the cursor will disappear, and the next cursor will appear. Calibration is conducted by repeating this process 16 times. When the 17th point has been finally touched, setting information for the 16 points and the normal ending information, total of 17 byte data, are written into the EEPROM, and the screen returns to the TOP menu.
Page 74
http://www.xiaoyu163.com 3 7 63 1515 0 [Coordinate inspection] [Outline] The coordinate before correction and after correction at the time of pressing the touch panel are displayed for coordinate verification. Furthermore, the red "+" cursor can be moved by the key operaiont mentioned bellow, and the coordinate of the cursor center is displayed.
Page 75
http://www.xiaoyu163.com 3 7 63 1515 0 [Calibration verification] [Outline] Touch the cursor “+” displayed on the screen. The correct touch will delete the cursor and another cursor will be displayed. The incorrect touch will make the characters of cursor turn red. Repeat this for 4 points, and “OK”...
Page 76
http://www.xiaoyu163.com 3 7 63 1515 0 [Data initialization] [Outline] Result of outermost circumference inspection and of calibration inspection (corrected value) are returned to their initial values. As for the initialized items, the initial values are written into the EEPROM and the adjustment information is cleared.
Page 77
http://www.xiaoyu163.com 3. EEPROM Adjust 3 7 63 1515 0 [Method for Mode IN] Choose "EEPROM Adjust" among the monitor test mode menu screen. [Display specifications] The setting items and the adjusted values are displayed on each page. *The adjusted value section indicates initial values stored in EEPROM. *If writing a value fails, the indication will not change.
Page 78
http://www.xiaoyu163.com 5. Display Test 3 7 63 1515 0 [Method for Mode IN] Choose "Display Test (Test Pattern)" among the monitor test mode menu screen. [Display specifications] [Operation specification] Operational description Remote controller key Selection cursor up movement Selection cursor down movement Page up Page down Return to test mode mene...
Page 79
http://www.xiaoyu163.com 3 7 63 1515 0 [RAMP & 10STEP] Display of step signal and signal for alpha blend check [Operation specification] Operational description Remote controller key alpha blend rate up alpha blend rate down Return to test mode mene Next signal [RASTER SIGNAL] Display of signal for step confirmation [Operation specification]...
http://www.xiaoyu163.com 6.2 DVD TEST MODE 3 7 63 1515 0 Test mode display will not appear on the display of this product. Connect the rear monitor output to a monitor. Image of the test mode. [MUTE] + [FORWARD] + Reset start Switch position of the remote control unit.
Page 81
http://www.xiaoyu163.com 3 7 63 1515 0 2 x 00 0000 (3),(4) CRG +/- Focus Jump Power_OFF Tracking balance When L0 layer: 2000 0000 It operates while the key 2FFF 0000 When L1 layer: 2100 0000 is being pressed. 2B00 0000 : CRG+ TBAL coefficient (layer 0) 2C00 0000 : CRG- TBAL coefficient (layer 1)
Page 82
http://www.xiaoyu163.com 3 7 63 1515 0 Legend: … Key operation EDC. Image of the test mode … Operational state … The content displayed on the DVD mechanism (video only) 8 characters data is sent to the product side (HOST) by UART communication. EDC1/2 test mode [Note] Image is the same for both EDC1 and EDC2.
Page 83
http://www.xiaoyu163.com Simple test mode 3 7 63 1515 0 The selection of the figure of each screen can be selected by "Key command for the test". <Flow chart> TEST MODE 1: LD ON 2: ASMAX 3: Skew Adjustment 4: Error Rate 5: CRG Move Outer 6: Eject Please Input Number...
http://www.xiaoyu163.com 7. DISASSEMBLY 3 7 63 1515 0 Removing the Monitor Assy (Fig.1) Case Remove the Case.(Fig.1) Monitor Assy Remove the four screws.(Fig.1) Remove the two hooks.(Fig.1) Fig.1 Disconnect the two FFC and then remove the Monitor Assy.(Fig.2) Fig.2 Removing the LCD Assy (Fig.3) Holder LCD Assy L 13942296513...
Page 85
http://www.xiaoyu163.com 3 7 63 1515 0 Removing the DVD Mechanism Module (Fig.6) Remove the four screws. Disconnect the FFC and then remove the DVD Mechanism Module. Fig.6 DVD Mechanism Module Removing the Heat Sink and Holder (Fig.7) Heat Sink Holder Remove the two screws.
Page 86
http://www.xiaoyu163.com 3 7 63 1515 0 Removing the Service Unit (Mother Assy) (Fig.11) Service Unit (Mother Assy) Remove the two screws. Straighten the tabs at two locations indicated. Remove the two screws and then remove the Service Unit (Mother Assy). Fig.11 When unplugging the Coaxial Jumper, make sure to use jig GGF1539.
Page 87
http://www.xiaoyu163.com 3 7 63 1515 0 How to have it 1.Have a specified part. Handling OK Handling NG L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 88
http://www.xiaoyu163.com 3 7 63 1515 0 Mecha Module_Bringing into the Clamp State with No Disc Loaded 1. Remove the relay FFC from the connector on the module PCB side (Fig. 1). (Precaution) When it is difficult to apply 4V to the motor in procedure 2 below, remove the connector on the relay PCB side, then remove the FFC, and remove the solder of the CRG motor lead and apply voltage to the lead.
Page 89
http://www.xiaoyu163.com CRG Mecha_Bringing into the Clamp State with No Disc Loaded 3 7 63 1515 0 1.Remove the T-case washer and then remove the drive gear. (Fig. 1) 2.Lift the clamp arm assy until it is in the state shown in Fig. 2_b (open-lock state). 3.Put your finger on the area A of Fig.
Page 90
http://www.xiaoyu163.com Removing the Module PCB 3 7 63 1515 0 1.Short-circuit two spots on the land of the pick up FPC. (Fig. 1) 2.Remove the pick up FPC and the relay FFC from the connector. (Fig. 2) 3.Temporarily attach the pick up FPC to the pick up rack. (Fig. 3) (in order to prevent the damage to the pick up FPC) 4.Remove the two PCB clinch screws and then remove the module PCB.
Page 91
http://www.xiaoyu163.com Removing the PU Unit 3 7 63 1515 0 1.Hook the feed screw biasing spring on the temporary hook (Fig. 2b). Be careful not to get injured by the tip of the spring. 2.Hold the PU at the location A in Fig. 1 and slide and scoot it to the direction of the inner periphery. 3.As in Fig.
http://www.xiaoyu163.com 8. EACH SETTING AND ADJUSTMENT 3 7 63 1515 0 8.1 DVD ADJUSTMENT 1) Precautions This product uses 5 V and 3.3 V as standard voltages. If the reference voltage is connected to GND by The electrical potential that is the reference for signals, mistake, turn the regulator OFF immediately, or is not GND, but VREF (approximately 2.2 V) and VHALF turn the power OFF.
Page 93
http://www.xiaoyu163.com 3 7 63 1515 0 - SKEW adjustment When one of the following replacements has taken place, SKEW adjustment for the pick up will be required. (1) Replacement of the pick up unit (2) Replacement of the spindle motor (3) Replacement of the carriage chassis (4) Replacement of the main shaft of the pick up unit Measurement equipment and tools/jigs: Oscilloscope...
Page 94
http://www.xiaoyu163.com There are two methods of making adjustment: a method of making adjustment through monitoring RF waves by the 3 7 63 1515 0 oscilloscope (method 1) and a method of making adjustment through checking the numerical value of the RF level by OSD (method 2).
Page 95
http://www.xiaoyu163.com 3 7 63 1515 0 Skew Adjustment 1: Power OFF RF Level : 000000 Please Input Number 9. Skew Adjustment Select “1: Power OFF.” Skew Adjustment 1: Power OFF RF Level : 000000 Please Input Number 10. TEST MODE Select “6: Eject.”...
Page 96
http://www.xiaoyu163.com 3 7 63 1515 0 Disc Detection Arm 13. CRG Move Outer Select “1: DVD Single Layer.” CRG Move Outer 1: DVD Single Layer 2: DVD Dual Layer 3: CD 4: CD-RW 5: Return L 13942296513 Please Input Number The pickup moves to the outer periphery.
Page 97
http://www.xiaoyu163.com Locations to make SKEW adjustment 3 7 63 1515 0 Locations to adhere the SKEW 1,2,3: GEM1033 L 13942296513 u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 98
http://www.xiaoyu163.com Bond for resonance 4:Three Bond 1530 3 7 63 1515 0 L 13942296513 adhesive Bond for locking the screw 5,6 : Three Bond 1401M Bond for locking the screw u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
Page 99
http://www.xiaoyu163.com Precautions on handling the PU 3 7 63 1515 0 *Precaution: Do not touch those shaded areas in the following figures. Hologram (Beware of the static) Do not touch the optical part RF level adjusting part Do not touch the spring L 13942296513 u163 AVH-P3200BT/XNUC...
http://www.xiaoyu163.com 9. EXPLODED VIEWS AND PARTS LIST 3 7 63 1515 0 OTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Page 105
http://www.xiaoyu163.com (1) PACKING SECTION PARTS LIST Mark No. Description Part No. 3 7 63 1515 0 Mark No. Description Part No. Cord Assy CDP1301 Clip Holder See Contrast table (2) Screw Assy See Contrast table (2) Cushion See Contrast table (2) Polyethylene Bag CEG-127 Remote Control Unit...
Page 106
http://www.xiaoyu163.com Owner's Manual,Installation Manual 3 7 63 1515 0 Part No. Language CRB3174 English CRB3175 French CRB3176 Spanish(Espanol) CRD4452 English, French, Spanish(Espanol) CRB3177 English CRB3178 Traditional Chinese CRB3179 Korean CRD4453 English, Traditional Chinese, Korean CRB3276 English CRB3180 Spanish(Espanol) CRB3181 Portuguese(B) CRD4454 English, Spanish(Espanol), Portuguese(B) CRB3182...
http://www.xiaoyu163.com 9.4 DVD MECHANISM MODULE 3 7 63 1515 0 ( C ) ( C ) ( C ) ( B ) ( A ) ( A ) ( C ) L 13942296513 ( A ) ( A ) ( C ) ( A ) ( C ) ( C )
Page 113
http://www.xiaoyu163.com DVD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Part No. 3 7 63 1515 0 Mark No. Description Part No. Holder CNW1195 Screw BMZ20P020FTC Screw BSZ20P040FTC Damper CNW1197 Screw(M2 x 4) CBA1835 Damper CNW1198 Washer CBF1038 Connect PCB Unit CWX3618 Spring CBH2860...
Page 114
http://www.xiaoyu163.com 3 7 63 1515 0 ( A ) ( A ) ( C ) ( C ) ( C ) ( C ) ( C ) ( C ) ( C ) ( A ) L 13942296513 ( A ) ( A ) u163 (A) : GEM1045...
http://www.xiaoyu163.com 10. SCHEMATIC DIAGRAM 3 7 63 1515 0 10.1 MOTHER UNIT(AUDIO) Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". ANA-SYS BUS ANA-I/F BUS REARMUTE2 REARMUTE1 R202 R204 R203 R205 RCAMUTE...
Page 117
http://www.xiaoyu163.com 3 7 63 1515 0 UMD2N MOTHER UNIT (AUDIO) model P : AVH-P3200BT/XNUC Q164 Q : AVH-P3250BT/XNRD BUP_1 SYS+B 14.4V 8.3V J : AVH-P3200DVD/XNUC Q163 2SC4116(GRBL) K : AVH-P3250DVD/XNRC UMD3N L : AVH-P3250DVD/XNRD E2 4 M : AVH-P3250DVD/XNRI MUTE1 Q155 GNDA GNDA...
Page 153
http://www.xiaoyu163.com 3 7 63 1515 0 MONITOR PCB (GERDA) GD33V 3.3V PNLVI PNLVI 3.4V C5401 CN5501 4.7u/6.3 VKN2040-A C5402 GD33V 3.3V SYSTEM UNIT PART 5001 TOUCH PANELPART 5101 POWER PART 5201 GNDD VIDEO PART 5301 GRST1 FLASH ROM PART 5401 TRCST GERDA IC PART 5501...
Page 159
http://www.xiaoyu163.com 3 7 63 1515 0 M-60 MONITOR PCB (BACKLIGHT) to BACK LIGHT CN5701 CKS5561-A SYSTEM UNIT PART 5001 TOUCH PANELPART 5101 POWER PART 5201 VIDEO PART 5301 GNDBLP GNDD FLASH ROM PART 5401 GERDA IC PART 5501 LCD PANEL PART 5601 R5704 BACKLIGHT PART...
http://www.xiaoyu163.com 10.14 WAVEFORMS 3 7 63 1515 0 - DVD CORE UNIT Note:1. The encircled number denote measuring points in the circuit diagram. 2. Reference voltage: 1.65 V(TD1,FD1)(=VHALF) 2.2 V(RF)(=VREF) In the waveform, it is seeing on the GND standard. Offset of 1.65 V or 2.2 V is put in.
http://www.xiaoyu163.com 11. PCB CONNECTION DIAGRAM 3 7 63 1515 0 11.1 MOTHER UNIT NOTE FOR PCB DIAGRAMS MOTHER UNIT 1.The parts mounted on this PCB include all necessary parts for CN2501 several destination. S/PDIF OUT For further information for respective destinations, be sure JA581 to check with the schematic dia- gram.
Page 165
http://www.xiaoyu163.com 3 7 63 1515 0 SIDE A N2501 RCA V IN OUT FRONT/REAR OUT JA562 JA561 ANTENNA JA402 IC151 C569 C568 C567 D561 D563 P561 R572 R570 R567 R571 R568 C564 R569 P562 R156 Q163 C161 R161 D562 R574 Q162 R573 C163...
http://www.xiaoyu163.com 11.8 BT ANT PCB 3 7 63 1515 0 BT ANT PCB SIDE A KN3801 CN3811 BT MODULE L 13942296513 BT ANT PCB SIDE B u163 AVH-P3200BT/XNUC http://www.xiaoyu163.com...
http://www.xiaoyu163.com 12. ELECTRICAL PARTS LIST 3 7 63 1515 0 NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS..) CKS.., CCS.., CSZS..The >...
Page 183
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Q 121 (B,44,96) Transistor LTC114EUB D 561 (A,121,114) Diode DZ2S068C 3 7 63 1515 0 Q 122 (B,47,90) Transistor UMX1N D 562 (A,114,113) Diode DZ2S068C Q 123 (B,21,91) Transistor UMT1N D 563...
Page 184
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. >P1651 (A,155,19) Fuse 1.5 A CEK1282 R 253 (B,141,103) RS1/16SS471J 3 7 63 1515 0 >P1711 (A,71,69) Fuse 1.25 A CEK1281 R 254 (B,144,103) RS1/16SS471J >P1721 (A,73,55) Fuse 2 A CEK1284 R 255 (B,146,103)
Page 185
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 371 (A,74,102) RS1/16SS102J R 584 (B,23,105) (Q,K,L,M) RS1/16SS104J 3 7 63 1515 0 R 372 (A,75,104) RS1/16SS152J R 585 (B,27,107) (Q,K,L,M) RS1/16SS103J R 373 (A,21,53) RS1/16SS333J R 586 (A,125,110) RS1/16SS223J...
Page 186
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 731 (B,137,44) RS1/16SS473J R 850 (A,55,22) RS1/16SS470J 3 7 63 1515 0 R 734 (A,109,36) (P,Q,J,L,M) RS1/16SS473J R 854 (A,53,22) RS1/16SS331J R 735 (A,109,38) (M) RS1/16SS473J R 856 (A,86,21) RS1/16SS473J...
Page 187
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1003 (A,14,64) RS1/10SR2R2J 3 7 63 1515 0 R 1004 (A,11,65) RS1/10SR2R2J C 207 (B,121,91) CKSRYB105K10 R 1005 (A,14,65) RS1/10SR2R2J C 208 (B,101,90) CKSRYB105K10 R 1006 (A,15,72) RS1/16SS911J C 211...
Page 188
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. 3 7 63 1515 0 C 301 (A,92,75) CCSSCH6R0D50 C 804 (A,50,40) CKSRYB104K10 C 302 (A,90,79) CCSSCH6R0D50 C 805 (A,49,35) CKSSYB104K10 C 303 (A,97,75) CCSSCH6R0D50 C 806 (A,49,33) CKSSYB104K10 C 304...
Page 189
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. 3 7 63 1515 0 C 982 (B,108,41) CKSSYB473K10 C 1772 (B,34,43) CKSRYB334K10 C 983 (B,112,32) CKSSYB102K50 C 1781 (B,12,44) (P,Q) CKSRYB104K16 C 984 (B,107,32) CKSSYB102K50 C 1782 (B,12,52) (P,Q) CKSRYB104K16 C 985...
Page 190
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. D 3508 (A,18,61) LED NSSM025A-A0886 CN5701 (A,17,16) Connector CKS5561 3 7 63 1515 0 D 5201 (A,130,69) Diode 1SR154-400 CN7501 (A,66,22) Connector CKS6180 D 5701 (A,29,31) Diode RB160M-60 CN7502 (A,26,24) Connector...
Page 191
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 5314 (A,95,41) RS1/16SS1002D R 5710 (A,21,26) RS1/10SR8201D 3 7 63 1515 0 R 5315 (A,92,37) RS1/16SS472J R 5711 (A,21,24) RS1/10SR6202D R 5316 (A,87,36) RS1/16SS471J R 5713 (A,30,23) RS1/16SS472J R 5317...
Page 192
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 7523 (B,23,35) (P,Q) RS1/16SS102J C 5506 (A,58,39) CSZS100M10 3 7 63 1515 0 R 7524 (B,11,34) (P,Q) RS1/16SS102J C 5507 (A,59,41) CKSSYB104K10 R 7527 (B,21,35) (P,Q) RS1/16SS102J C 5508 (A,61,41)
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. C 5707 (A,13,31) CKSRYB105K10 CN1201 (A,16,44) Connector CKS6003 3 7 63 1515 0 C 5708 (A,21,22) CKSRYB474K10 CN1901 (A,21,7) Connector CKS6025 C 5710 (A,10,19) CKSRYB105K10 RESISTORS C 5711 (A,21,32) CKSSYB104K10 C 5713...
Page 194
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1506 (A,37,14) RS1/16SS101J C 1015 (B,7,8) CKSSYB102K50 3 7 63 1515 0 R 1507 (A,44,14) RS1/16SS101J C 1016 (B,12,10) CKSSYB102K50 R 1508 (A,43,15) RS1/16SS221J C 1018 (A,28,28) CKSSYB104K10 R 1509...
Page 195
http://www.xiaoyu163.com Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. C 1522 (A,65,34) CKSSYB104K10 3 7 63 1515 0 C 1523 (A,68,37) CKSSYB104K10 Pickup Unit(Service) CXX2398 C 1524 (A,69,37) CKSSYB473K10 Motor Unit(LOAD/CRG) CXC4026 C 1526 (A,68,37) CKSSYB103K16 Motor(SPINDLE) EXM1050 C 1528...