Connecting the Units ........ 1 Connecting the system ........3 CAUTION: Connecting the power cord (1) ......5 • PIONEER does not recommend that Connecting the power cord (2) ......7 you install or service your display your- When connecting to separately sold power self.
Note: • This unit cannot be installed in a vehicle with- out ACC (accessory) position on the ignition • Use this unit in other than the following condi- switch. tions could result in fire or malfunction. — Vehicles with a 12-volt battery and negative grounding.
Connecting the Units Connecting the system Antenna jack Blue Antenna cable (supplied) IP-BUS input AV-BUS input (Blue) (Blue) Violet Blue Hide-away unit (supplied) Blue IP-BUS cable (supplied with XDV-P650) AV-BUS cable (supplied with XDV-P650) Blue Black XDV-P650 (sold separately) Blue Black IP BUS STAND ALONE...
Page 5
Microphone/auxiliary input jack (3.5 ø) (MIC/AUX IN) Before installing this unit to your vehicle, pull out the jack to the place 1.5 m where you can easily plug in/out the microphone or stereo mini plug cable. 15 cm This product Use a stereo mini plug cable to connect with auxiliary equipment.
Connecting the Units Connecting the power cord (1) If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly. Black (chassis ground) Connect to a clean, paint-free metal location. Yellow After making all other connections to this unit, connect this to the positive + terminal of the battery.
Page 7
Power supply box (supplied) This product Yellow/black If you use equipment with Mute function, wire this lead to the Audio Mute lead on that piece of equipment. If not, keep the Audio Mute lead free of any connections. Fuse (7.5 A) Fuse resistor Fuse resistor Fig.
Connecting the Units Connecting the power cord (2) If this unit is used with more than a 6-ch speaker system, be sure to connect the yellow lead to the battery terminal directly. Hide-away unit (supplied) Connect when the audio settings of this product are used in the network mode.
Page 9
See the section “When Violet/white connecting with a rear view camera”. WARNING LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.
Connecting the Units When connecting to separately sold power amp Hide-away unit (supplied) See the section “Connecting the power cord (2)”. Blue/white Connect to system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC). System remote control Connect when the audio settings of this product are used in the network mode.
Page 11
Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) RCA cables (sold separately) Power amp (sold separately) Power amp (sold separately) Power amp (sold separately) Front center speaker Left Right Tweeter Tweeter Front middle range Front middle range speaker speaker Rear speaker...
Connecting the Units When connecting with a rear view camera When using this product with a rear view camera, automatic switching to video from a rear view camera when the gear shift is moved to REVERSE (R) position is possible. WARNING: •...
Page 13
Rear view camera To video output Hide-away unit (supplied) See the section “Connecting the power cord (2)”. CAUTION Pioneer recommends the use of a camera which outputs mirror reversed images, otherwise screen image may appear reversed. Extension lead (supplied) 15 cm...
Connecting the Units When connecting the external video component and the display To video input Display with RCA input jacks Hide-away unit To audio inputs RCA cables (sold separately) Video input 2 Video input 1 To audio outputs External video component (sold separately) To video output...
Page 15
About video input 1 Depending on the external video component connected to this unit, video image may be distorted. In this case, adjust the video image by switching the selector (selector is located on the bottom of the hide-away unit as illustrated). Use a thin standard-tip screwdriver to switch the selector.
Installation Note: • The cords must not cover up the area shown in the figure below. This is necessary to allow the • Check all connections and systems before final amplifires to radiate freely. installation. • Do not use unauthorized parts. The use of Hide-away unit unauthorized parts may cause malfunctions.
Installing the hide-away unit Before installing the unit • Remove the mounting sleeve. Mounting with Brackets (Fig. 14) Loosen the screws (2 mm × 3 mm) and then remove the mounting sleeve. Tapping screw (4 mm × 12 mm) Mounting sleeve Screw (2 mm ×...
Installation 2. Install the unit into the dash- DIN Rear-mount board. (Fig. 16) After inserting the mounting sleeve Installation using the screw holes on into the dashboard, then select the the side of the unit appropriate tabs according to the thickness of the dashboard material •...
• When installing in a shallow space, Installing the remote control unit use the following screw holes. In When not using the remote control this case, stick concealing tape on unit, secure it with the hook and loop parts that protrude from the dash- fastner to prevent it from moving.