Symbol DS6708 Quick Start Manual page 2

SYMBOL DS6708
1
OPTIMUM ARM POSITION
Standard Use
Low/medium/high beep
Power up
Parameter Menu Scanning
High/low/high/low beep
Successful
parameter
setting
SYMBOL DS6708
© 2010 MOTOROLA, INC. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability,
function, or design.
Motorola does not assume any product liability arising out of, or in connection
with, the application or use of any product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise
under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products
might be used. An implied license exists only for equipment, circuits, and
subsystems contained in Motorola products.
MOTOROLA, the Stylized M Logo and Symbol and the Symbol logo are registered
trademarks of Motorola, Inc. Other product names mentioned in this manual may
be trademarks or registered trademarks of their respective companies and are
hereby acknowledged.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Service Information
If you have a problem using the equipment, contact your facility's Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Motorola Enterprise Mobility Support at:
http://www.motorola.com/enterprisemobility/contactsupport.
For the latest version of this guide go to:
http://www.motorola.com/enterprisemobility/manuals.
Power Supply
Use ONLY a LISTED Motorola, Type no. 50-14000, or PWRS-14000, Direct Plug-In
power supply, marked Class 2 or LPS, or SELV, Rated 5 Vdc, 850 m A Min.
(IEC 60950-1). Use of alternative power supply will invalidate any approvals given
to this device and may be dangerous.
Motorola, Inc.
One Motorola Plaza Holtsville, New York 11742-1300, USA
MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered
in the U.S. Patent and Trademark Office. All other product or service names are the
property of their respective owners.
© Motorola, Inc. 2010
72- 83973 -01 Revision C March 2010
SYMBOL DS6708
2
3
1 LED Indicators
2 Scan Window
3 Scan Trigger
AVOID EXTREME WRIST ANGLES
BEEPER INDICATIONS
Short medium beep 4 long low beeps
Bar code decoded
High/low beep
Correct programming
sequence performed
123Scan 2 is an easy-to-use, PC-based software tool that enables rapid and easy customized setup via a bar code or USB
cable. For more information, visit: http://www.motorola.com/123Scan 2 .
REGULATORY INFORMATION
Ergonomic Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic injury follow
the recommendations below. Consult with your local Health & Safety Manager to
ensure that you are adhering to your company's safety programs to prevent
employee injury.
• Reduce or eliminate repetitive motion
• Maintain a natural position
• Reduce or eliminate excessive force
• Keep objects that are used frequently within easy reach
• Perform tasks at correct heights
• Reduce or eliminate vibration
• Reduce or eliminate direct pressure
• Provide adjustable workstations
• Provide adequate clearance
• Provide a suitable working environment
• Improve work procedures.
Regulatory Information
Symbol Technologies, Inc., the Enterprise Mobility business of Motorola, Inc.
("Motorola").
All Symbol devices are designed to be compliant with rules and regulations in
locations they are sold and will be labeled as required.
Any changes or modifications to Symbol Technologies equipment, not expressly
approved by Symbol Technologies, could void the user's authority to operate the
equipment.
Radio Frequency Interference Requirements
Tested to comply
with FCC Standards
FOR HOME OR OFFICE USE
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Symbol Technologies, Inc., hereby declares that this device is in compliance with all
the applicable Directives, 89/336/EEC, 73/23/EEC. A Declaration of Conformity may
be obtained from http://www.motorola.com/enterprisemobility/doc.
http://www.motorola.com/ds6708
OPTIMUM SCANNING
0 1 2 3 4 5
0 1 2 3 4 5
AVOID EXTREME
WRIST ANGLES
Transmission error
detected; data is
ignored
Low/high beep
Incorrect
programming
sequence or
"Cancel" bar code
scanned
123SCAN
2
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide
reasonable protection against harmful
Aiming
AVOID BENDING AND REACHING
LED INDICATIONS
Off Green
Scanner is on Bar code is successfully
and ready to scan, decoded
or no power to
scanner
Laser Devices
Symbol products using lasers comply with US 21CFR1040.10
and1040.11 except for deviations pursuant to laser notice no.
50, dated June 24, 2007 and IEC 60825-1 (Ed. 2.0),
EN60825-1:2007.
The laser classification is marked on one of the labels on the product.
Class 1 Laser devices are not considered to be hazardous when used for their
intended purpose. The following statement is required to comply with US and
international regulations:
Caution: Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous laser light exposure.
Class 2 laser scanners use a low power, visible light diode. As with any very bright
light source, such as the sun, the user should avoid staring directly into the light
beam. Momentary exposure to a Class 2 laser is not known to be harmful.
Scanner Labeling
LASER LIGHT- DO NOT STARE INTO
BEAM . CLASS 2 LASER PRODUCT.
LASERSTRAHLUNG - NICHT IN DEN
STRAHL BLICKEN. LASER KLASSE 2.
LUMI»RE LASER - NE PAS REGARDER
DANS LE FAISCEAU. APPAREIL ¿ LASER
DE CLASSE 2 630-680nm, 1mW
Recommended Usage Guide
0 1 2 3 4 5
0 1 2 3 4 5
AVOID BENDING
AVOID REACHING
Alternate left and right hands Alternate left and right hands
taking breaks and task rotation taking breaks and task rotation
recommended recommended
Red
Transmission
error
Local Contact: