Table of Contents
Advertisement
5. ENVIRONMENTAL CONDITIONS
5.1.
Temperature. When welding, the temperature should not be below -10ºC or above 40ºC. During storage or transit the temperature
should not fall below -25ºC or rise above 55ºC.
5.1.1 Humidity. The relative humidity should be no greater than 50% at 40ºC or 90% at 20ºC.
5.1.2 Altitude. The welder can be used up to 1000 Metres only.
6. OPERATION
WARNING! If you have no welding experience, we recommend you seek supervised training from an expert source.
6.1.
Introduction. Your welder features a single phase transformer with a drooping characteristic suitable for welding with an alternating
current using stick electrodes with diameters from 1.5mm to the highest electrode diameter as shown on the chart below (See fig.7).
6.2.
Current regulation. The intensity of the welding current can be adjusted continuously by means of a manually operated magnetic
shunt. See fig.4.6. The value of the current (I²) may be read in amps on the graduated scale on the top panel of the welder (See fig.3).
6.3.
Thermostatic Protection.
6.3.1. Temperature Control Indicator Light. See Fig. 4.2.
When the machine is overheating, it cuts off the power and the indicator light comes on. When the temperature has dropped to the
recovery temperature, the machine can automatically restart and the indicator light will go off.
6.3.2 Temperature Protection Indicator Light. See Fig. 4.3.
If the Temperature Controller fails, the protector will cut off the power and the indicator light comes on. Temperature protection can not
resume automatically. If needed, please follow the methods below for recovery operations:
1. Turn off the machine's power.
2. Open the cover of the machine.
3. When the temperature protector pops up on the red contacts, such as in the picture right,
off.
4. Press the red contacts on the thermal protection
welding rods you may experience a temporary current shut off. The larger the welding rod, the greater the current required,
consequently, the hotter the machine will become and the quicker it will cut out.
6.4.
Setting up the welder.
6.4.1 Ensure the machine is turned off from the mains power supply. See fig.4.1.
6.4.2 Insert the quick connector for the work clamp lead into the socket marked with the work clamp symbol. See fig.4.5. Rotate the
connector fully through 180º to ensure a secure connection. Attach the work clamp to a point on the workpiece that has been cleanly
ground to provide good contact. Attach it as close as possible to the joint to be made.
6.4.3. Insert the quick connector for the electrode holder lead into the socket marked with the electrode holder
Rotate the connector fully through 180º to ensure a secure connection. See fig.4.4.
6.4.4 Select the diameter of electrode to be used in relation to the type of joint to be made. Consideration should be
given to the fact that higher current values should be used for flat welding, whereas for vertical or over head
welding lower current values are required. Insert the electrode into the electrode holder. Ensure there is a good
connection. Ensure welding surfaces are kept clean and free from grease, or oil.
6.4.5 Establish the welding current required in relation to the diameter of electrode you are using by making reference
to the table below (fig.7.)
6.4.6 Set the current required in amps using the control wheel on the front panel. See fig.4.6. Turn the control clockwise
to increase the current, and anti-clockwise to decrease the current. The current set can be read from the graduated
scale on the top panel of the machine. See Fig.3.
6.5.
Commencing welding. It is advisable to practice on scrap metal first especially where potentially difficult
welds are to be undertaken.
WARNING! Remember to wear a full face welding mask, gauntlets and protective clothing, and
ensure you have read, understood and apply safety instructions. Wear goggles whilst chipping
slag.
6.5.1 DO NOT switch on the power supply until you are fully ready to start welding.
6.5.3 Place the face mask in front of your face.
6.5.4 To strike the arc, tap the electrode lightly on the workpiece as if striking a match. DO NOT hit the electrode
on the workpiece as this may damage the stick.
6.5.5 As soon as the arc is struck maintain a steady gap between the end of the electrode and the workpiece
equal to the diameter of the electrode in use (See fig.5). Try to maintain this gap continuously through out
the duration of the weld. The electrode should also be held at an angle of 20° to 30° from the vertical. (See fig.6).
6.5.6 At the end of the weld bead, move the tip of the electrode backwards in order to fill the weld crater. Quickly lift the electrode from the
weld pool to extinguish the arc. Refer to fig.8 for a welding fault analysis.
6.5.7 If the electrode sticks, you may be holding it too close to the workpiece. Pull sharply to the left, and then to the right to free the
electrode.
6.5.8 After welding, chip off the slag with the chipping hammer provided. Always wear goggles.
6.5.9 Disconnect welder from the mains power supply before resetting the electrode holder.
WARNING! Use pliers to remove the hot consumed electrodes or to move the hot welded pieces.
Electrode Diameter (mm) ...... Welding Current (Amp)
1.6 ................................ 25min ............... 50max
2.0 ................................ 40min ............... 80max
2.5 ................................ 60min ............... 110max
3.2 ................................ 80min ............... 160max
4.0 ................................ 105min ............. 185max
5.0 ................................ 130min ............. 220max
© Jack Sealey Limited
this means the machine is now in a normal state. As you use larger
fig.8
fig.7
Original Language Version
it means the machine has cut
symbol.
fig.5
fig.6
180XT.V2
Issue: 1 - 08/08/14
Advertisement
Table of Contents
