Hitachi C12LSH Handling Instructions Manual page 17

To process crown
molding at positions molding at positions
Type of
1 and 4 in Fig. 41.
Crown
Molding
Miter Angle Bevel Angle Miter Angle Bevel Angle
Setting Setting
45° Type right 35.3° left 30°
( mark) ( mark)
38° Type right 31.6° left 33.9°
( mark) (
(1) Setting to cut crown moldings at positions 1 and 4
in Fig. 41 (see Fig. 42; tilt the motor head to the left):
1 Turn the turntable to the right and set the Miter
Angle as follows:
* For 45° type crown moldings: 35.3° ( mark)
* For 38° type crown moldings: 31.6° ( mark)
2 Tilt the motor head to the left and set the Bevel
Angle as follows:
* For 45° type crown moldings: 30° ( mark)
* For 38° type crown moldings: 33.9° ( mark)
3 Position the crown molding so that the upper
surface (A in Fig. 40) contacts the fence as indicated
in Fig. 44.
(2) Setting to cut crown moldings at positions 2and 3
in Fig. 41 (see Fig. 43; tilt the head to the left):
1 Turn the turntable to the left and set the Miter
Angle as follows:
* For 45° type crown moldings: 35.3° ( mark)
* For 38° type crown moldings: 31.6° ( mark)
2 Tilt the head to the left and set the Bevel Angle as
follows:
* For 45° type crown moldings: 30° ( mark)
* For 38° type crown moldings: 33.9° ( mark)
3 Position the crown molding so that the lower
surface (B in Fig. 40) contacts the fence as in
Fig. 45.
1
Miter angle scale
Turntable
To process crown
2 and 3 in Fig. 41.
Setting
left 35.3°
( mark)
left 31.6°
mark) ( mark)
Head
Bevel angle scale
4
Fence (A)
Base
Fig. 42
Setting
left 30°
( mark)
left 33.9°
( mark)
(3) Setting to cut crown moldings at positions 1 and 4
in Fig. 41 (see Fig. 46; tilt the head to the right):
1 Turn the turntable to the right and set the Miter
Angle as follows:
* For 45° type crown moldings: 35.3° ( mark)
* For 38° type crown moldings: 31.6° ( mark)
2 Tilt the head to the right and set the Bevel Angle
as follows:
* For 45° type crown moldings: 30° ( mark)
* For 38° type crown moldings: 33.9° ( mark)
3 Position the crown molding so that the upper
surface (B in Fig. 40) contacts the fence as indicated
Fig. 48.
(4) Setting to cut crown moldings at positions 2 and 4
in Fig. 41 (see Fig. 47; tilt the head to the right):
1 Turn the turntable to the left and set the Miter
Angle as follows:
* For 45° type crown moldings: 35.3° ( mark)
* For 38° type crown moldings: 31.6° ( mark)
2 Tilt the head to the right and set the Bevel Angle
as follows:
* For 45° type crown moldings: 30° ( mark)
* For 38° type crown moldings: 33.9° ( mark)
3 Position the crown molding so that the lower
surface (A in Fig. 40) contacts the fence as in Fig.
49.
Head
Bevel angle scale
2
Fence (B)
Turntable
Fig. 43
Fence
A
Table on base
Fig. 44
Fence
B
Table on base
Fig. 45
3
Miter angle scale
Base
B
A
17