SERVICE MANUAL COMPACT COMPONENT SYSTEM MB188 2004 HX-GD8 Area suffix J ----------------------------- U.S.A. C -------------------------- Canada SP-HXGD8 CA-HXGD8 SP-HXGD8 TABLE OF CONTENTS PRECAUTION............... . . 1-3 SPECIFIC SERVICE INSTRUCTIONS .
Page 2
SPECIFICATION Amplifier section CA-HXGD8 195 W per channel, min. RMS, driven into 6 Ω at 63 Hz with no more than 10 % total harmonic Output Power SUBWOOFERS distortion. 80 W per channel, min. RMS, driven into 6 Ω at 1 kHz with no more than 10 % total harmonic MAIN SPEAKERS distortion.
SECTION 1 PRECAUTION Safety Precautions (1) This design of this product contains special hardware and voltmeter. many circuits and components specially for safety purpos- Move the resistor connection to each exposed metal es. For continued protection, no changes should be made part, particularly any exposed metal part having a return to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across...
Page 4
Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Page 5
Importance administering point on the safety Primary board (Forward side) F001 6.3A-125V F101 F102 F103 F104 Caution: For continued protection against risk of fire, replace only with same type 6.3 A/125 V for F001, 8 A/125 V for F101 and F102, 3.15 A/125 V for F103, 1.6 A/125 V for F104.
SECTION 3 DISASSEMBLY Main body section 3.1.1 Removing the metal cover (See Figs.1 to 3) (1) From the back side of the main body, remove the six screws A attaching the metal cover. (See Fig.1.) Metal cover (2) From the both sides of the main body, remove the two screws B attaching the metal cover.
Page 8
3.1.2 Removing the front panel assembly (See Figs.4 to 7) • Prior to performing the following procedures, remove the metal CN205 cover. Bridge board Parallel wire (1) From the right side of the main body, disconnect the card wires from the connectors (CN43, CN44, CN802, CN803) on the main board.
Page 9
3.1.3 Removing the tuner (See Figs.8 and 9) • Prior to performing the following procedures, remove the metal CN502 CN560 cover. Card wires (1) From the right side of the main body, disconnect the card wire from the connector CN560 on the main board.
Page 10
3.1.5 Removing the rear panel (See Figs.10 to 12) • Prior to performing the following procedures, remove the metal Tie band cover. (1) From the top side of the main body, remove the tie band bundling the wires. (See Fig.10.) Bridge board Reference: After reassembling, bundle the wires with the new tie...
Page 11
3.1.7 Removing the main board (See Figs.13 and 14) • Prior to performing the following procedures, remove the metal Main board cover, tuner, video board and rear panel. (1) From the right side of the main body, disconnect the card CN803 CN110 Card wires...
Page 12
3.1.8 Removing the main amplifier board/subwoofer amplifier boards (See Figs.15 to 17) • Prior to performing the following procedures, remove the metal Wires cover, tuner, video board, rear panel and main board. (1) From the top side of the main body, disconnect the wires Bridge board from the connector (CN206, CN208) on the bridge board.
Page 13
3.1.9 Removing the connection board (See Fig.18.) • Prior to performing the following procedure, remove the metal Connection board cover, tuner, video board, rear panel, main board and main amplifier/subwoofer amplifier boards. (1) From the top side of the main body, remove the two screws R attaching the connection board on the chassis base.
Page 14
3.1.11 Removing the 5DVD changer mechanism assembly (See Figs.21 to 23) • Prior to performing the following procedures, remove the metal Front panel assembly cover, tuner, video board, rear panel, main board and bridge board. 5DVD changer mechanism assembly (1) From the both sides of the main body, remove the two screws T attaching the 5DVD changer mechanism assem- bly to the front panel assembly.
Page 15
3.1.12 Removing the primary board (See Figs.19, 21, 22, 24 and 25) • Prior to performing the following procedures, remove the metal Primary board cover, tuner, video board, rear panel and main board. (1) From the top side of the main body, release the wire holder bundling the wire.
Page 16
3.1.14 Removing the switch board (See Fig.27) • Prior to performing the following procedures, remove the metal Front panel assembly cover and front panel assembly. (1) From the inside of the front panel assembly, remove the three screws Z attaching the switch board. (2) Take out the switch board and remove the soldered section w on the switch board to remove the parallel wire.
Page 17
3.1.16 Removing the encoder board (See Figs.26 to 29) • Prior to performing the following procedures, remove the metal Volume knob cover and front panel assembly. Sound mode knob (1) From the outside of the front panel assembly, pull out the knobs toward this side.
Page 18
3.1.17 Removing the microphone board (See Fig.30) • Prior to performing the following procedure, remove the metal Microphone board cover and front panel assembly. From the inside of the front panel assembly, remove the seven screws AC and screw AC' attaching the microphone board. Reference: •...
DVD changer mechanism assembly section 3.2.1 Removing the tray assemblies (See Figs.1 to 5) (1) From the top side of the main body, remove the two screws A from the top cover and release the two joints a on the Open det.
3.2.2 Removing the DVD servo board (See Figs.6 to 8) Caution: Short land sections d Solder the short land sections d on the DVD pickup before dis- connecting the card wire extending from the DVD pickup. If you do not follow this instruction, the DVD pickup may be dam- DVD pickup aged.
Page 21
3.2.4 Removing the motor board (See Figs.9 and 10) (1) From the top side of the DVD changer mechanism assem- bly, remove the two belts from the motor pulleys. (See Fig.9.) Note: Take care not to attach grease on the belt. Belt Belt (2) Remove the four screws F attaching the motors to the load-...
Page 22
3.2.6 Removing the DVD traverse mechanism assembly (See Fig.11) • Prior to performing the following procedures, remove the tray DVD changer mechanism assembly assemblies and DVD servo board. (1) From the bottom side of the DVD changer mechanism as- sembly, remove the three screws H attaching the DVD traverse mechanism assembly.
Page 23
3.2.7 Removing the DVD pickup (See Figs.12 to 14) • Prior to performing the following procedures, remove the tray DVD traverse mechanism assembly assemblies, DVD servo board and DVD traverse mechanism Screw shaft gear assembly. Connector Card wire (1) From top side of the DVD traverse mechanism assembly, release the lock of the connector on the DVD pickup and disconnect the card wire in the direction of the arrow.
Page 24
3.2.9 Removing the spindle motor board (See Figs.15 and 16) • Prior to performing the following procedures, remove the tray Card wire assemblies and DVD traverse mechanism assembly. (1) From the top side of the DVD traverse mechanism assem- SF motor base bly, remove the four screws M attaching the DVD traverse Spindle motor board mechanism assembly to the DVD traverse mechanism...
Page 25
3.2.10 Removing the motor (See Figs.17 and 18) • Prior to performing the following procedures, remove the tray SF motor base Motor assemblies, DVD traverse mechanism assembly, DVD pickup and spindle motor board. • Remove the wires of the motor as required. (1) Remove the middle gear in the direction of the arrow.
Page 26
3.2.11 Removing the side (L) assembly and tray switch board (See Figs.19 to 21) • Prior to performing the following procedures, remove the tray SIde(L) assemblies. (1) From the topside of the DVD changer mechanism assem- bly, remove the two screws T attaching the side (L). (See Fig.19.) (2) From the left side of the DVD changer mechanism assem- bly, remove the spacer fixing the tray switch board and mo-...
Page 27
3.2.12 Removing the side (R) assembly (See Fig.22 to 26) • Prior to performing the following procedures, remove the tray Elevator spring assemblies and DVD servo board. (1) From the inside of the side (R) assembly, release the two tabs u of the gear cover and remove the gear cover out- Elevator cam ward.
Page 28
3.2.13 Removing the lifter assembly (See Figs.27 to 31) • Prior to performing the following procedures, remove the tray Hook assemblies, DVD servo board, side (L) and side (R) assembly. (1) From the top side of the DVD changer mechanism assem- bly, turn the gear 1 clockwise to move the lifter assembly upward.
Page 29
3.2.14 Removing the rack holder and sensor assembly (See Figs.32 to 38) • Prior to performing the following procedures, remove the tray Slide gear assemblies, side (L), side (R) assembly and lifter assembly. Reference: If the slide gear of the DVD changer mechanism assembly Rack holder places at joint ad of the rack holder, turn the gear 1 counter- clockwise to move the slide gear in the direction of the arrow.
Page 30
Slider Sensor spring Fig.36 Sensor board SV. resister Sensor bracket Slider Fig.37 Sensor assembly Sensor gear Slide lever Sensor spring Fig.38 1-30 (No.MB188)
Page 31
3.2.15 Taking out the disc in the play mode (See Fig.39 to 42) Reference: Disc Refer to "Removing the tray assemblies". Tray assembly (1) From the top side of the DVD changer mechanism assem- bly, remove the top cover. (2) Unlock the tray assemblies and draw out the tray assem- blies toward the front.
Page 32
Cassette mechanism assembly 3.3.1 Removing the Play/Record & Clear head Cassette mechanism assembly Fly wheelR (See Fig.1~3) (1) While moving the trigger arm on the right side of the head mount in the direction of the arrow, turn the flywheel R counterclockwise until the head mount comes ahead and clicks.
Page 33
3.3.2 Removing the head amplifier & mechanism control board (See Fig.4) (1) Turn over the cassette mechanism assembly and remove Main motor assembly the three screws A attaching the head amplifier & mecha- nism control board. Capstan belt (2) Disconnect the flexible wire from connector CN31 on the head amplifier &...
Page 34
3.3.4 Removing the flywheel (See Fig.8, 9) • Prior to performing the following procedure, remove the head amplifier & mechanism control board and the main motor as- sembly. (1) From the front side of the cassette mechanism, remove the slit washers attaching the capstan shaft L and R. Pull out the flywheels backward.
Page 35
3.3.6 Reattaching the Play/ Record & Clear head (See Fig.11~13) (1) Reattaching the head mount assembly. a) Change front of the direction cover of the head mount assembly to the left (Turn the head forward). b) Fit the bosses O', P', Q', U' and V' on the head mount assembly to the holes P and V, the slots O, U and Q of the mechanism sub assembly (See Fig.11 to 13).
Page 36
Speaker section 3.4.1 Removing the side panel assembly (See Fig.1) (1) From the side of the speaker main body, remove the four screws A and two screws B attaching the side panel as- sembly. Side panel assembly Fig.1 3.4.2 Removing the subwoofer (See Fig.2) •...
Page 37
3.4.3 Removing the front panel assembly (See Figs.3 and 4) Reference: Front panel assembly Remove the side panel assembly as required. (1) Remove the four screws D attaching the front panel as- sembly. (See Fig.3.) (2) Release the two joints a. (See Fig.3.) Caution: When removing the front panel assembly from the speaker main body, do not break or damage them that...
Page 38
3.4.5 Removing the top woofer (See Fig.5) • Prior to performing the following procedures, remove the front Top woofer panel assembly. (1) Remove the four screws F attaching the top woofer. (2) From the back side of the top woofer, disconnect the red and black wires from the terminal.
SECTION 4 ADJUSTMENT Measurement Instruments Required for Adjustment (1) Low frequency oscillator 4.2.2 Tuner section This oscillator should have a capacity to output 0dBs to FM Band cover 87.5~108.0MHz 600Ω at an oscillation frequency of 50Hz-20kHz. AM Band cover 530~1,710kHz (2) Attenuator impedance : 600Ω...
Page 40
Cassette mechanism adjustment Head azimuth Head azimuth adjustment screw adjustment screw (Forward side) (Reverse side) CN31 Head azimuth Head azimuth R/P head, Erase head adjustment screw adjustment screw (Forward side) (Reverse side) Mecha control board Motor speed VR37 VR37 R371 FW100 CN33 C374...
Page 41
4.3.1 Mechanism section Item Condition Measurement method Ref. value Adjust- ment posi- tion Head azimuth Test tape (1) Playback the test tape VT703L (8kHz). Maximum output Only adjust :VT703L (8kHz) (2) Adjust to maximum output level by azi- at changed Output terminal muth adjustment screw for forward side head...
Page 42
4.3.2 Electrical adjustment Item Condition Measurement method Ref. value Adjust- ment posi- tion Recording BIAS • Forward or Reverse (1) Set the test tape(AC-514 TYPE ll and AC-225 VR31 adjustment • Test tape AC-225 TYPE l), then make REC/ : 4.20µA : AC-514 TYPE ll PAUSE condition.
Page 43
Service mode 4.4.1 Confirming contents (1) System micon reset (2) System micon cold start (3) FL display check (4) Micon version check (5) DVD region check (6) DVD test mode 4.4.2 Confirming methods 1. System micon reset When CD mechanism stuck, this may solve the problem without removing/inserting power cord. Press the STANDBY/ON, CANCEL and PAUSE buttons on the main unit simultaneously.
Page 44
You can confirm DVD region number. Press the POWER and DVD LEVEL buttons on the main unit at standby. DVD region number is indicated on the on screen display. FL indication (Example) "JC ver.0334 HX-GD8 / FMU-SD7-11" REGION DVD unit number Firmware model Firmware version DVD destination 1-44 (No.MB188)
Page 45
6. DVD test mode Insert the power cord in an outlet while pressing the SET and buttons on the main unit. Status: You can check DVD unit condition (Example) "TEST JC 13" DVD unit condition is indicated on the FL Disc reading preset condition display.
Page 46
Device key: Program DEVICE KEY code STANDBY/ON LED blink. Press the button on the main unit. PC application run. Automatically power off Wait until PC application complete Reference: FL indication Device key check: Check device key checksum If never programmed, "FFFF" (Example) "...
Page 47
DVD jitter: DVD single-layer jitter display FL indication Press the "6" button on the remote controller. " " FL indication EEPROM (B): EEPROM data display (Backward) Press the "7" button on the remote controller. " " EEPROM (F): EEPROM data display (Forward) FL indication Press the "8"...
Page 48
4.4.3 Indicating check for FL display Function FL display Note SOURCE DVD-VIDEO DVD-AUDIO If MP3 time is over 100 minutes, show "--:--". If WMA time is over 100 minutes, show "--:--". without PBC with PBC SVCD without PBC with PBC DVD (JPEG) TAPE : PRESET NUMBER...
Page 49
Function FL display Note 3D PHONIC 3D ACTION 3D DRAMA 3D THEATER 3D PHONIC OFF Note: DVD-A cannot be activated 3D-Phonic. Also at Karaoke condition, 3D-PHONIC is TONE SETTING TONE MEMORY RANGE: -3 TONE MEMORY RANGE: -3 TONE MEMORY NUMBER BLINKING TONE MEMORY TONE MEMORY DVD LEVEL...
Page 50
Function FL display Note REC TIMER SELECT HOUR BLINKING MINUTE BLINKING HOUR BLINKING MINUTE BLINKING BLINKING BLINKING BLINKING TEST (ROM) by Remocon "B332" ROM correction +3 CHARACTORS 4 CHARACTORS (including ROM CORR) BACKEND VERSION 4 CHARACTORS J / E / A / US / UW / UX TEST (REGION) 0/1/2/3/4/5/6 DVD STATUS...
Page 51
Function FL display Note DVD AUDIO STOP After TOC READING +10KEY INPUT PLAY PLAY (MENU) PAUSE TIME BLINKING SEARCH RESUME STOP RESUME RESUME PLAY RESUME OFF BEFORE PLAY DOWNMIX PROHIBITED WATERMARK STOP (without PBC) DISPLAY TOTAL TIME STOP (with PBC) PLAY (PBC OFF) PLAY (PBC ON) PAUSE (PBC OFF)
Page 52
Function FL display Note PROGRAM PROGRAM MODE DISC INPUT (10key) Group # Blink, 10-key and ENTER key input GROUP INPUT Track # Blink, 10-key and ENTER key input TRACK INPUT STOP PLAY DEPEND ON DISC TYPE FULL MEMORY RANDOM RANDOM MODE R A N SEARCH D O M...
Page 53
Function FL display Note DEMO OFF BEEP BEEP ON BEEP OFF TRAY LOCK LOCK UNLOCK (No.MB188)1-53...
Page 54
Function FL display Note DVD TEST MODE TEST START By AC cord on with holding SET and (Version info) : VERSION @: FE learning condition #: REGION A. EEPROM INITIALIZE By pressing PAUSE (Front) (NORMAL) B. EEPROM INITIALIZE By pressing and holding (Front) for 2-sec (FULL) DEVICE KEY DISPLAY...
SECTION 5 TROUBLESHOOTING This service manual does not describe TROUBLESHOOTING. (No.MB188)1-55...
Page 56
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MB188) Printed in Japan...
Page 57
SCHEMATIC DIAGRAMS COMPACT COMPONENT SYSTEM HX-GD8 CD-ROM No.SML200404 Area suffix J ----------------------------- U.S.A. C -------------------------- Canada SP-HXGD8 CA-HXGD8 SP-HXGD8 Contents Block diagram Standard schematic diagrams 2-19 to 27 Printed circuit boards No.MB188SCH COPYRIGHT 2004 VICTOR COMPANY OF JAPAN, LTD. 2004/4...
Page 58
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " " mark nearby are critical for safety.
Block diagram DVD servo / DVD system control section EXDAT0 to 15 TUNER EXADT0 to 15 A,B,C,D,E,F,RF+,LPC1,LPC2 EXADR16 to 20 NEXCE,NEXOE LPCO1 IC509 NEXWE LPCO2 Q101 FLASH ROM LD(CD) CDLDCUR LD(DVD) Q102 DVDLDCUR CN560 CPURST CPURST Q103 TDATA Q104 SDATA IC453 MECHA SPDIF...
Page 61
Video output S-VIDEO OUT section & COMPOSITE YO,CO OPTICAL COMPU IC100 CB,CR VIDEO OUT AV LINK VIDEO VIDEO-RGB DRV. J108 J123 CN502 Y,Cb,Cr COMPONENT VIDEO-LPF Y/C-MIX External input Yout VIDEO OUT MUTE1,MUTE2 Cout Source select CrOUT SPDIF switch section CbOUT COMPOUT 9V,M9V S5V,5.6V...
Page 62
Standard schematic diagrams Primary with main transformer section FW204 QJK015-082614 T001 QQT0425-001 F101 8A-125V F102 8A-125V F103 S4CT 3.15A-125V F104 1.6A-125V FW202 QUM154-21DGZ4 R275 SGND R277 S3CT Parts ar When re sure to...
Page 63
F001 6.3A-125V R200 3.3M Parts are safety assurance parts. When replacing those parts make sure to use the specified one. SHEET 1...
Page 88
VICTOR COMPANY OF JAPAN, LIMITED AV & MULTIMEDIA COMPANY AUDIO/VIDEO SYSTEMS CATEGORY 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan Printed in Japan (No.MB188SCH)
PARTS LIST [ HX-GD8 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J ----------------------------- U.S.A. C -------------------------- Canada - Contents - 3- 2 Exploded view of general assembly and parts list (Block No.M1) 3- 5 Speaker assembly and parts list (Block No.M2)
Page 90
Exploded view of general assembly and parts list Block No. Bridge board Standby LED board FL board FL900 Switch board Microphone board Headphone board...
Page 91
Video board Subwoofer amplifier board Primary board Main amplifier board Main board Encoder board Connection board 115 116...
Page 92
General assembly Block No. [M][1][M][M] Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local QYSBSGY3008E SPECIAL SCREW 3mm x 8mm(x2) QYSBSGY3008E SPECIAL SCREW 3mm x 8mm GV10177-005A FRONT PANEL QYSBSF3012E SPECIAL SCREW 3mm x 12mm GV40313-001A FELT SPACER...
Page 93
Speaker assembly and parts list Block No. Speaker Block No. [M][2][M][M] Symbol No. Part No. Part Name Description Local 829929752019 F.PANEL ASSY L. 829929752020 F.PANEL ASSY R. 439929418530 SIDE PANEL LEFT 439929418526 SIDE PANEL RIGH 249929786106 "8SUBWOOFER"" (x2) 249929723606 5CM TWEETER (x2) 249929757002...
Page 94
DVD mechanism assembly and parts list Block No. FXL-D52-1M Grease =JVG-31N =JVS-1003...
Page 95
DVD mechanism Block No. [M][J][M][M] Symbol No. Part No. Part Name Description Local LV10751-001A TM CHASSIS LV10752-003A SF MOTOR BASE QAR0308-001 SPINDLE MOTOR LV43461-001A SPECIAL SCREW (x3) QAR0144-003 MOTOR VKS5557-001 F.M. GEAR QYSPSPT2030M SCREW M2 x 3mm LV33985-001A MIDDLE GEAR QYSDST2008Z TAP SCREW M2 x 8mm(x2)
Page 96
DVD changer mechanism assembly and parts list Block No. FMU-SD7-15M Grease =JVG-31N =JVS-1003 CH5-BASE-1M...
Page 97
DVD changer mechanism Block No. [M][K][M][M] Symbol No. Part No. Part Name Description Local LV10743-004A CHASSIS ASSY LV10913-001A LOADER ASSY QVY0027-B14 S V RESISTOR QYSDST2004Z SCREW 2mm x 4mm QAR0164-001 MOTOR (x2) LV42340-001A MOTOR PULLEY (x2) LV41431-002A BELT (x2) QYSPSPU1725N SCREW 1.7mm x 2.5mm(x2)
Page 98
Cassette mechanism assembly and parts list Block No. SLC-S302M Grease = EM-30L =UD-24 =LEN-320M =MOBIL-1 The lower side Switch board Head amplifier board 3-10...
Page 99
Cassette mechanism Block No. [M][P][M][M] Symbol No. Part No. Part Name Description Local VKS1165-00N CHASSIS B. ASSY VKS2274-002 REEL GEAR (x2) VKW5286-002 B.T. SPRING (x2) VKS5559-001 PLAY IDLE GEAR VKS5595-002 BLIND VKS5560-003 FR IDLE GEAR LV42013-001A EARTH SPRING SLC-RP4SVM HEAD MOUNT ASSY VKY3149-002 CASSETTE SP.
Page 101
Input board Symbol No. Part No. Part Name Description Local Block No. [0][2][0][0] D807 1SS133-T2 DIODE Symbol No. Part No. Part Name Description Local D808 1SS133-T2 DIODE D809 MTZJ4.3B-T2 Z DIODE D811 1SS133-T2 DIODE IC401 LC75342M-X D813 1SS133-T2 DIODE IC442 JCV8011-X...
Page 102
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C475 NCB31HK-222X C CAPACITOR 2200pF 50V K C1003 QDXB1CM-222Y C CAPACITOR 2200pF 16V M C476 NCB31CK-153X C CAPACITOR 0.015uF 16V K C1004 QDGB1HK-102Y C CAPACITOR 1000pF 50V K...
Page 103
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R503 QRE141J-562Y C RESISTOR 5.6kΩ 1/4W J R818 NRSA63J-221X MG RESISTOR 220Ω 1/16W J R504 QRE141J-103Y C RESISTOR 10kΩ 1/4W J R819 NRSA63J-102X MG RESISTOR 1kΩ...
Page 104
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R900 NRSA02J-221X MG RESISTOR 220Ω 1/10W J S907 QSW0825-001Z TACT SW R901 NRSA02J-221X MG RESISTOR 220Ω 1/10W J SP03 LV30225-011A SPACER R902 NRSA02J-221X MG RESISTOR 220Ω...
Page 105
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C602 QCBB1HK-221Y C CAPACITOR 220pF 50V K C1128 QETN1AM-477Z E CAPACITOR 470uF 10V M C603 QCBB1HK-221Y C CAPACITOR 220pF 50V K C1129 QCBB1HK-181Y C CAPACITOR 180pF 50V K...
Page 106
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local R737 QRE141J-104Y C RESISTOR 100kΩ 1/4W J CN912 QGF1205F1-18 CONNECTOR FFC/FPC (1-18) R738 QRE141J-104Y C RESISTOR 100kΩ 1/4W J FL900 QLF0133-001 FL TUBE ...
Page 107
DVD servo board Symbol No. Part No. Part Name Description Local Block No. [0][5][0][0] C334 NCB31CK-104X C CAPACITOR 0.1uF 16V K Symbol No. Part No. Part Name Description Local C335 NCB31CK-104X C CAPACITOR 0.1uF 16V K C337 NCB31CK-183X C CAPACITOR 0.018uF 16V K C338...
Page 109
Symbol No. Part No. Part Name Description Local Symbol No. Part No. Part Name Description Local C104 QCBB1HK-221Y C CAPACITOR 220pF 50V K R342 QRE141J-243Y C RESISTOR 24kΩ 1/4W J C105 QCBB1HK-391Y C CAPACITOR 390pF 50V K R343 QRE141J-183Y C RESISTOR 18kΩ...
Page 110
Packing materials and accessories parts list Block No. A2, A4, A5, A6, A7, A8, A9, A10, 3-22...
Page 111
Packing and accessories Block No. [M][3][M][M] Symbol No. Part No. Part Name Description Local GVT0125-002A INST BOOK ENG,FRE GD8C GVT0125-001A INST BOOK GD8J GV40511-001A NOTICE SHEET GV40510-001B CAUTION SHEET BT-51028-2 REGISTER CARD GD8J YU20333 SAFETY INST. QAM0216-001 SIGNAL CORD QAL0014-001 AM LOOP ANT QAL0457-001...