Advertisement
Advertisement
Table of Contents
Related Manuals for Hifonics Titan TXi4408
Summary of Contents for Hifonics Titan TXi4408
-
Page 2: General Installation Procedure
GENERAL INSTALLATION PROCEDURE System Design The success of any car stereo system relies on several factors, such as the system design, execution of the installation, and system setup. Please remember that any system is only as good as its weakest link. Please remember that higher power systems are not necessarily useful purely for high sound pressure levels, but also to establish a headroom capability, to reproduce musical peaks cleanly without distortion. -
Page 3: Amplifier Feature Descriptions
Each model is capable of 4 & 2-Ohms stereo per channel, or 4-Ohms mono bridged operation All Hifonics amplifiers feature a comprehensive diagnostic system, with speaker lead short circuit, except the mono amps which are capable of 4, 2 and 1-Ohm loads. -
Page 4: Full Range Stereo
TO BATTERY + 12 volts VIA FUSE REMOTE TURN-ON CHASSIS GROUND FULL RANGE MONO This application illustrates the basic mono bridging method for all Hifonics 2 channel Switch setting checklist: amplifiers. - The AMPLIFIER X-OVER switch must be in the FULL position. -
Page 5: Remote Turn-On
TXi4008 / TXi6008 2-CHANNEL AMPLIFIER APPLICATIONS Stereo high pass with mono low-pass in a 2 way active, or bi-amplified system In this application we will use a 2 channel amplifier for the high frequencies, and a second Lows amplifier: one for the low frequencies, or mono sub bass. Please consult the speaker specifications - HI PASS (Subsonic filter): 10 Hz to 40 Hz to determine maximum amplifier power requirements. - Page 6 Here we show how to use the 4 channel amplifiers as full range 2 or 3 channel units by Channels 1/2: taking advantage of the mono bridging capability of all Hifonics amplifiers. - HI PASS: N/A - LOW PASS: N/A The following example shows how to create a 3 channel system by mono bridging channel pair 3 / 4.
- Page 7 TXi4408 / TXi6408 4 CHANNEL AMPLIFIER APPLICATIONS 2 way active, or bi-amplified system with mono bass Channels 3/4: This application shows how easily a 2 way active system can be implemented using a 4 - HI PASS (subsonic): 20 Hz channel amplifier.
-
Page 8: Basic Application
TXi7508 A/B CLASS 1 CHANNEL AMPLIFIER APPLICATIONS Basic application Crossover frequency control checklist: These sub bass amplifiers can be used in any of the bi-amplification systems described in LOW PASS: 40Hz to 150Hz this manual, replacing the 2 channel amplifiers as per the illustrations. SUBSONIC:15 Hz to 55 Hz Interconnect cable checklist: BASS EQ: 0 to +12dB... - Page 9 TXi1008D / TXi1508D / D CLASS 1 CHANNEL AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: Minimum final loudspeaker impedance: - Connect the line inputs to a Radio/CD RCA outputs or line output of the - 1 ohm. full range primary amplifier with good quality RCA cables. A “Y” adapter may be needed as shown in the diagram.
-
Page 11: Setting Up Systems After Installation For Best Performance
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE TXi4008 / TXi6008 / TXi4408 / TXi6408 General: At this point you are ready to get more specific on the settings for your amplifier. High Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. -
Page 12: Troubleshooting A System
2 - Make sure that no speaker leads are shorting to exposed metal on the vehicle chassis. 3 -RCA cables are notorious for their problematic nature, so check that these are good, in particular the shield connections. CAR AMPLIFIERS HIFONICS AMPLIFIERS...