Table of Contents
Advertisement
H 1
17
Blue wire
H2/15 Grey wire
Trunk Pin
6
Hood Pin
Instant trigger: a heavier impact
On board shock sensor
detected
by
the anboard shock sensor
Door switch trigger
Hl/8 Green or Hl/6 Violet wire
Instant trigger: For optional sensors
Optional MUX port
Ignition trigger
H3/1 Pink wire
Note: See Owner's guide for more details
Remote Pairing
1
Press and hold the
f
button for 8 seconds until the main menu appears.
2.
Press and release the {:) button until
I
Remote Pair
I
text is displayed,
3.
Press and release the
f
button until
CE9l!J
text is displayed,
4.
Press and hold the'" button until tones are played on the LC3 remote.
5.
Successful or Failed Pair: The LC3 remote control indicates a successful or
foiled pairing on the display.
Note: Please see installation gUide for pairing with the l-way companion remote
Note: If no remote pairing results, the system will exit after 60 seconds.
Ia.hI.ulf
Zones
A zone is represented by the number
of
stotus LED floshes used by the
system to identify
0
porticulor type
of
input.
Prepare the vehicle system to
be
Paired with a new remote
1
Open a door
2
Turn the key to the ON position
3.
Within 5 seconds press and release the Control bullon on the system's Control
Center one time.
Within 5 seconds. press and hold the Control button on the Control Center.
The status LED will flash one time and the siren will chirp once to confirm the
system is ready for remote pairing
5.
Release the Control button and proceed below.
Prepare the new remote to
be
Paired with the system
Make sure the LC3 remote is set for the desired Cor 1 (Default) or Cor 2 opera-
tion
Menu 3- Remote start
Menu 2- Convenience
Options: OFF,
·20°
to 7(J'
in
10°
increments
Options:
112/3/4
10 24 in 2
hoor
incremenlS
Options: OfF, 40°
to
130
0
in 1
(J'
increments
Options:
1/213/4
10 24 (Stortsl in incremenls of 2
OptionS: OFF,
qv
to
125V
in
05V
increments
Feature Menus
Default settings ore in bold type. New features ore bold with grey oockground
Menu 1- Security
To access another feature in the same menu:
1
Press and release the Control button the number
of
times necessary to advance
from the feature yau just programmed to the next one you wont to program
Then press the Control button once more and hold it,
To select another menu:
1
Press and hold the Control button.
2
After 3 seconds, the unit advances to the next menu and the siren chirps, indi-
cating which menu has been acces5ed
Once a feature is programmed:
•
Other features can be programmed within the same menu
Another menu can
be
selected
The learn routine can
be
exited if programming is complete
For features with only two options; '"
=
option I while.
=
option 2
For leatures with more than two options; '" selects the options in ascending order,
while. selects them in descending order
Note: Pressing
~~:)
button resets the feature to the factory default
Open a door.
Turn the ignition on, then off
Select a Menu. Press and hold the Control button. The number
of
siren chirps
indicates the menu number. 1 chirp indicates menu 1, 2 chirps - menu 2 and
3 chirps for menu 3
4.
When the desired menu chirps ore heard. release the Conlrol button.
S
Select a Feature. Press and release the Control button the number of times
corresponding
10
the feature you wish
10
change. Then press and hold one
more lime to select the features.
6.
Program the Feature, While holding the
Conlrol
button, you con program
the
feature using the remote control.
H
If programming with the Bitwriter®, the learn routine can
be
locked or un-
a
locked. If the learn routine has previously been locked, it must
be
unlocked
-
with Bitwrite!® . thiS cannot
be
done manually with the Control button.
The Bilwriter®
II
gives you access to a wider range of systerr: opti?ns. These
features and
th~iustments
that may
be
programmed are descnbed
In
the table
below. Default settings are in bold
type
~
Opl.2
The learn routine exits if any of the following occurs:
The open door is closed
The ignition is turned On
There is no activity lor 30 seconds
The Control button is pressed too many times
Bilwriter - Only Options
~51emleatures,
_
The System Features Learn Routine dictates how the unit operates.
It
is possible to
occess and change masl of the feature settings using the Control button
o
2009 Directed Electronks.Allrights ReseNed
LAD5702t
Advertisement
Table of Contents
