Table of Contents
Advertisement
External Control Device Setup
18. Bass (Command2:s)
G To adjust bass.
You can also adjust bass in the Sound menu.
Transmission
[[k][s][
][Set ID][ ][Data][Cr]
J
Data
Min: 0 ~ Max: 64
° Refer to 'Real data mapping 1'. See page 38.
Acknowledgement
[[s][ ][Set ID][ ][OK][Data][x]
J
19. Balance
(Command2:t)
(3 To adjust balance.
You can also adjust balance in the Sound menu.
Transmission
[[k][t][
][Set ID][ ][Data][Cr]
J
Data
Min: 0 ~ Max: 64
• Refer to 'Real data mapping 1'. See page 38.
Acknowledgement
[[t][ ][Set ID][ ][OK][Data][x]
J
20. Color
Temperature
(Command2:u)
(3 To adjust color temperature.
You can also adjust ACC in the Picture menu.
Transmission
[[k][u][
][Set ID][ ][Data][Cr]
J
Data
0: Cool
1: Normal
2: Warm
3: Off
Acknowledgement
[[u][ ][Set ID][ ][OK][Data][x]
J
21. Red Adjustment
(Command2:v)
G To adjust red in color temperature.
Transmission
[[k][v][
][Set ID][ ][Data][Cr]
J
Data
Min: 0 ~ Max: 3C
° Refer to 'Real data mapping 3' as shown right.
Acknowledgement
[[v][ ][Set ID][ ][OK][Data][x]
J
22. Green
Adjustment
(Command2:w)
G To adjust green in color temperature.
Transmission
[[k][w][
][Set ID][ ][Data][Cr]
J
Data
Min: 0 ~ Max: 3C
° Refer to 'Real data mapping 3' as shown right.
Acknowledgement
[[w][ ][Set ID][ ][OK][Data][x]
J
40
Plasma TV
23. Blue Adjustment
(Command2:$)
(3 To adjust blue in color temperature.
Transmission
[[k][$][ ][Set ID][ ][Data][Cr]
I
Data
Min: 0 ~ Max: 3C
• Refer to 'Real data mapping 3' as shown below.
Acknowledgement
[[$][ ][Set ID][ ][OK][Data][x]
I
* Real data mapping
3
0
-30
1
-29
2
-28
1E
0
3A
+28
3B
+29
3C
+30
24. PIP Input Select (Command2:y)
G To select input source for sub picture in PIP mode.
Transmission
I[k][y][ ][Set ID][ ][Data][Cr]
I
Data 0 :TV
4 :Component2
1 :Video1
5 : RGB
2 :Video2
6 : DVI
3 : Component
1
Acknowledgement
I[y][ ][Set ID][ ][OK][Data][x]
I
25. Abnormal State (Command2:z)
(3 To recognize an abnormal state.
Transmission
[[k][z][ ][Set ID][ ][FF][Cr]
Data
FF:Read
Acknowledgement
I[z][ ][Set ID][ ][OK][Data][x]
I
Data 0: Normal (Power on and signal exist)
1: No signal (Power on).
2: Turn the monitor off with remote control.
3: Turn the monitor off with Sleep Time function.
4: Turn the monitor off with RS-232C function.
5: 5V down.
6: AC down.
7: Turn the monitor off with Fan Alarm function.
8: Turn the monitor off with Off Time function.
9: Turn the monitor off with Auto Off function.
a: Turn the monitor off with On Time function.
(If you do not press any button within 2 hours after
the TV turns on with the On Timer function, the TV will
automatically
revert to standby mode.)
Advertisement
Table of Contents
