1. Manuals
  2. Brands
  3. York Manuals
  4. Air Conditioner
  5. Taurus Series
  6. Installation and operation instructions manual

York Taurus Series Installation And Operation Instructions Manual

Window ac
Hide thumbs
Table of Contents

Advertisement

Quick Links

Taurus Series
YORK Window Air Conditioners
IOM IOWRCAG50220711A1

Advertisement

Table of Contents
loading

Related Manuals for York Taurus Series

Summary of Contents for York Taurus Series

  • Page 1 Taurus Series YORK Window Air Conditioners IOM IOWRCAG50220711A1...
  • Page 2 Warning 1. Before using the Air conditioner please read the instructions carefully. They contain important advise about the installation, operation & maintenance of your Air conditioner. 2. Please keep this manual in a safe place for future user. 3. The Manufacturer cannot be held responsible for any injury or damage to person, animals or property if the following has not been observed.

  • Page 3: Installation

    23. This appliance is not intended for use by person (including children) with reduced physical, sensory or mettal capabilities or lack of expereince and knowledge. Unless they have been given supervison or instruction concerning use of appliance when it is put into operation. 24.
  • Page 4 200mm 90 cm Min. WINDOW OPENING DIMENSION FOR MOUNTING CLEARANCE AT THE REAR SIDE Fig. - B Fig. - C 50cm BEVELLED SIDES CLEARANCE AT THE SIDES WHEN CLEARANCE AT THE SIDES WALL THICKNESS EXCEEDS 200 mm. Fig. - D Fig.
  • Page 5 The Cabinet should be secured to the Wooden Frame In order to prevent the Unit from falling down. Holes are provided on the Left, Right & Bottom sides of the Cabinet (See Fig. - G) for fixing it to the Wooden Frame. Choose a side of the Wooden Frame which is right angle to the bottom surface to fix the Cabinet and use Nails or Screws (Not supplied) for fixing it.
  • Page 6 200mm 5 to 10 mm TYPICAL INSTALLATION Fig - H Rectangular Opening Base Tray Top Side Drain Side Base Outlet Tray View Side View Drain Outlet Side Drain Tube Drain Tube Before Assembly After Assembly Fig - 1 Notes : a.
  • Page 7 SHIPPED POSITION OPERATIONAL POSITION Fig - J Fig. - M Fig. - N...

  • Page 8: Operation / Mode - Switch

    3. Operation Instruction Control Panel is located at the Lower Right bottom of the Air conditioner. Units with and without Control Panel Cover are available. To access a Control Panel with Cover, Press at Point [C] marked with "PUSH" to unlock the Control Panel Cover and move it from DOWN "D" position to UP "U" position for locking it.

  • Page 9: Indicator Light

    c Air Swing - Switch To Auto Deflect the Conditioned Air from Left to Right & Back with Vertical Air Deflectors, push the Switch to the ON position and OFF position to stop. If you require the Air to be deflected to one particular direction, then Switch ON the Air Swing switch and OFF the switch when the Deflectors are in the required direction.
  • Page 10 b. Plastic Front Panel The Plastic Front Panel can easily become dirty. To clean it, shut power *OFF*, remove Front Panel & Wipe it with a soft dry cloth. When it is extremely dirty, wipe with a soft cloth containing lukewarm water or neutral soap. Then wipe thoroughly with a soft dry cloth.
  • Page 11 FOR WINDOW AIR CONDITIONER MODELS WITH REMOTE CONTROL FRONT PANEL KEY PAD OPERATION INSTRUCTION Notes 1. Unit can be operated either the front panel key pad Or from the remote control handset. 2. For switching ON or OFF the unit, always use the ON/OFF button of the front panel key pad Or the ON/OFF button of the remote control handset.
  • Page 12 C. FAN BUTTON - By pressing this button each time the fan speed will change in the following sequence. - This will be indicated by the LED lights on the Control Panel Key Pad. Š HIGH AUTO There is no AUTO fan speed available in FAN mode. D.
  • Page 13 FAN SPEED DISPLAY - Show the selected Fan speed Auto, Low, Med Or High. J. IR SIGNAL RECEIVER - Receives signals from the infrared transmitter. - Don’t close this opening with any hard object since it will object the proper reception of signals from the transmitter.

  • Page 14: Operation

    OPERATION 1. TRANSMISSION SOURCE - Before starting the operation from the handset, keep the handset’s transmission source at line of sight with the signal receiver 2. ON/OF - Each press off this button will turn ON or OFF the unit. - On every press, ON/OFF status will be indicated by the displays at the receiver side.

Table of Contents