Table of Contents
Advertisement
users guide
ESPRIT 2
Your Ideal users guide
24, 30, 35
When replacing any part on this appliance use only spare parts that you can be assured
conform to the safety and performance specification that we require. Do not use
reconditioned or copy parts that have not been clearly authorised by Ideal.
May 2010
UIN 206104 A01
Advertisement
Table of Contents
Related Manuals for IDEAL ESPRIT 2 24
Summary of Contents for IDEAL ESPRIT 2 24
- Page 1 When replacing any part on this appliance use only spare parts that you can be assured conform to the safety and performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised by Ideal. May 2010...
-
Page 2: Electricity Supply
Benchmark Commissioning Checklist. You can check your installer by calling Gas Safe Register direct on 0800 4085500 Ideal Stelrad Group is a member of the Benchmark scheme and fully supports the aims of the programme. Benchmark has been introduced to improve the standards of installation and commissioning of central heating systems in the UK and to encourage the regular servicing of all central heating systems to ensure safety and efficiency. -
Page 3: To Shut Down The Boiler
O p e r a t i o n Boiler overheat thermostat Winter conditions - i.e. CH and DHW required. This thermostat will shut down the boiler in the event of overheating. Should this occur a fault code “ ” will be The boiler will fire and supply heat to the radiators but will give displayed. -
Page 4: Troubleshooting
POINTS FOR THE BOILER USER Note. In line with our current warranty policy we would ask that you check through the following guide to identify any problems external to the boiler prior to requesting a service engineers visit. Should the problem be found to be other than with the appliance we reserve the right to levy a charge for the visit, or for any pre-arranged visit where access is not gained by the engineer. -
Page 5: Gmt/Bst Adjustment
ITIME PROGRAMMER ESPRIT 2 PROGRAMMER USER REFERENCE GUIDE 1 2 3 TIMED TIMED ADVANCE +1hr ADVANCE PROG time prog prog select select P R O G R A M M E R INTRODUCTION The ESPRIT 2 programmer allows the user to set the times at which they want the boiler to run for Central Heating (CH) and Domestic Hot Water (DHW). -
Page 6: Programming Mode Structure
ITIME PROGRAMMER PROGRAMMING MODE STRUCTURE Once the programming mode is entered the structure is as shown: are the UP and DOWN buttons Central heating times setting / delete The left hand “Timed” is flashing, Go to Frame 3 together with the radiator symbol The Radiator symbol is flashing, Radiator temperature setting together with “... -
Page 7: Setting The Day And Time
ITIME PROGRAMMER SETTING THE DAY AND TIME DISPLAY SHOWS time / day is the PROG button and backlight is OFF is the SELECT button Press ‘PROG’ button briefly are the UP and DOWN buttons DISPLAY SHOWS time / day and backlight is ON Press ‘PROG’... -
Page 8: Programming The Heating Periods
ITIME PROGRAMMER PROGRAMMING THE HEATING (OR HOT WATER) PERIODS DISPLAY SHOWS time / day is the PROG button and backlight is OFF is the SELECT button Press ‘PROG’ button briefly are the UP and DOWN buttons DISPLAY SHOWS time / day and backlight is ON Press ‘PROG’... -
Page 9: Setting The Hot Water Temperature
SETTING THE HOT WATER TEMPERATURE* DISPLAY SHOWS time / day is the PROG button and backlight is OFF is the SELECT button Press ‘PROG’ button briefly are the UP and DOWN buttons DISPLAY SHOWS time / day and backlight is ON Press ‘PROG’... - Page 10 QUICK REVIEW OF PROGRAMMED TIMES AND TEMPERATURES Note. This section cannot be used to amend the settings, is the PROG button see Frames 3 and 4. is the SELECT button are the UP and DOWN buttons DISPLAY SHOWS time / day and backlight is OFF Press ‘PROG’...
-
Page 11: Preset Program Times And Temperatures
PRESET PROGRAM TIMES AND TEMPERATURES The programmer comes with preset Central Heating and Hot Water times and temperatures. These can be amended using the appropriate procedures. The times can be deleted if they are not required (refer to Frame 8). Central Heating Periods: Hot Water Periods: MON-FRI... - Page 12 “ON” flashes, and a time is showing period altogether Ideal Consumer Helpline Ideal Stelrad Group pursues a policy of continuing improvement in the design and performance of its products. The right is therefore reserved to vary specification without notice. Tel: 01482 498660 Ideal Boilers, P.O.
-
Page 13: Itime Programmer Controls And Display
ITIME PROGRAMMER - CONTROLS AND DISPLAY "Heating" "Hot Water" Press this 1 2 3 Press this button to cycle button to cycle TIMED TIMED from 'TIMED' to from 'TIMED' to ADVANCE +1hr ADVANCE 'ADVANCE' then 'ADVANCE' then 'ON' and 'OFF'. 'ON' and 'OFF'.