How to assemble your monitor hardware ..............6 Rotating the monitor (optional) ....................7 Viewing angle adjustment .......................9 Getting the most from your BenQ monitor ..............10 Downloading the LCD Monitor driver files from the Internet ..........10 How to install the monitor on a new computer ................11 How to upgrade the monitor on an existing computer ..............12...
1. Getting started When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement. BenQ LCD Monitor Power Cord (Picture may differ from product supplied for your region.)
2. Getting to know your monitor Front view 1. Power button Back view 2. Control buttons 3. AC Power Input jack 4. Cable clip 5. DVI socket 6. D-Sub socket 7. Lock switch Above diagram may vary depending on the model. Getting to know your monitor...
3. How to assemble your monitor hardware If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Connect the PC video cable Either Do not use both DVI-D cable and D-Sub cable on the same PC.
Picture may differ from product supplied for your region. Turn on the monitor by pressing the power button. Turn on the computer too, and follow the instructions in Getting the most from your BenQ monitor Section 4: on page 10 to install the monitor software.
Page 8
Then tilt the monitor. 2. Rotate the monitor 90 degrees clockwise as illustrated. To avoid the edge of the LCD display hitting the monitor base surface while it is being rotated, do tilt and extend the monitor to the highest position before you start to rotate the display.
Viewing angle adjustment You may position the screen to the desired angle with -2° to +20° monitor tilt, 90° (left and right total) monitor swivel, and 130 mm monitor height. How to assemble your monitor hardware...
4. Getting the most from your BenQ monitor To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ website (http://www.benq.com/support). See...
BenQ LCD Monitor is the first ever monitor to be connected to it. If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Downloading the LCD Monitor driver files from the Internet on page 7. Click Next This will install the appropriate monitor driver files to your computer. Close 8. Click You may be prompted to restart your computer after the driver update is complete. Getting the most from your BenQ monitor...
Downloading the LCD Monitor driver files from the Internet on page 8. Click Next This will install the appropriate monitor driver files to your computer. Close 9. Click You may be prompted to restart your computer after the driver update is complete. Getting the most from your BenQ monitor...
The Monitor Properties window will display. If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper drivers are already installed, and you need do nothing further. Cancel out of these property windows.
If you wish, you can always adjust the screen geometric settings manually using geometry menu items. To assist you in this endeavour, BenQ has provided a screen test image utility which you can use to check for screen color, grayscale and line gradient display. The utility is available on the BenQ website.
6. How to adjust your monitor The control panel AUTO : Adjusts vertical position, phase, horizontal position and pixel clock automatically. MENU key: Activates OSD main menu and return to the previous menu or exit OSD. Display Mode key: For Up/Increase adjustment. The key is the hot key for Display Mode.
Hot key mode The monitor keys perform as hot keys to provide direct access to particular functions whenever the menu isn't currently displaying on-screen. Display Mode hot key Press the key continually to switch among , and . The Full Aspect Overscan setting will take effect immediately.
Main menu mode You can use the OSD (On Screen Display) menu to adjust all the settings on your monitor. Press the MENU key to display the following main OSD menu. There are four main OSD menus: 1. Display 2. Picture 3.
Display menu 1. Press the MENU key to display the main menu. 2. Press the keys to select DISPLAY and then press the ENTER to enter the menu. 3. Press the keys to move the highlight to a menu item and then press ENTER key to select that item.
Page 21
H. Position Adjusts the horizontal 0 to 100 Press the keys to position of the screen image. adjust the value. V. Position Adjusts the vertical position 0 to 100 of the screen image. Pixel Clock Adjusts the pixel clock 0 to 100 frequency timing to synchronize with the analog input video signal.
Picture menu 1. Press the MENU key to display the main menu. 2. Press the keys to select PICTURE and then press the ENTER to enter the menu. 3. Press the keys to move the highlight to a menu item and then press ENTER key to select that item.
Page 23
Color - Press ENTER to enter the Color menu This Color menu is available only in the Standard mode. Normal Allows video and still Press the keys to photographs to be viewed select this option. with natural coloring. This is the factory default color. Bluish Applies a cool tint to the image and is factory pre-set...
Picture Advanced menu MENU 1. Press the key to display the main menu. 2. Press the keys to select PICTURE ADVANCED and then press ENTER key to enter the menu. 3. Press the keys to move the highlight to a menu item and then press ENTER key to select that item.
Page 25
• ON Senseye Demo Displays the preview of Press the keys to screen images under the • OFF change the settings. selected mode from Picture Mode. The screen will be divided into two windows; the left window demonstrates images of Standard mode, while the right window presents the images under the specified...
Page 26
• RGB Color Format Determines the color space Press the ENTER key to (RGB or YUV) based on the select this option. Press the • YUV following detected video keys to change signal: the settings. • D-Sub (VGA) from PC: The default Color Format is RGB.
System menu 1. Press the MENU key to display the main menu. 2. Press the keys to select SYSTEM and then press the ENTER to enter the menu. 3. Press the keys to move the highlight to a menu item and then press ENTER key to select that item.
Page 28
H. Position Adjusts the horizontal 0 to 100 Press the keys to position of the OSD menu. change the settings. V. Position Adjusts the vertical position 0 to 100 of the OSD menu. • 5 Sec. Display Time Adjusts the display time of the OSD menu.
Page 29
*DDC/CI, short for Display Data Channel/Command Interface, which was developed by Video Electronics Standards Association (VESA). DDC/CI capability allows monitor controls to be sent via the software for remote diagnostics. How to adjust your monitor...
7. Troubleshooting Frequently asked questions (FAQ) The image is blurred: Read the instructions in Adjusting the screen resolution on page 33, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test.
“NO” in the “OSD Lock” submenu from the “OSD Settings” menu (under SYSTEM), and all OSD controls will be accessible. Need more help? If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: Support@BenQ.com. Troubleshooting...
Native Resolution V2410B 1920 x 1080 V2410T 1920 x 1080 To take full advantage of LCD technology you should select the native resolution setting of your PC screen as described below. Be aware that not all PC video cards provide this resolution value. If yours doesn't, check with the video card manufacturer's website for an updated driver for your particular model PC video card which supports this resolution.
Adjusting the screen refresh rate You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer.
Preset display modes Incoming display mode (Input timing) Resolution 1920X1080 640x480@60Hz 640x480@75Hz 720x400@70Hz 800x600@60Hz 800x600@75Hz 832x624@75Hz 1024x768@60Hz 1024x768@75Hz 1152x870@75Hz 1280x720@60Hz 1280X960@60Hz 1280x1024@75Hz 1360x768@60Hz 1600x900@60Hz 1680x1050@60Hz 1920x1080@60Hz • Image disruption may occur as a result of signal frequency differences from graphic cards which do not correspond with the usual standard.
Recognizing the importance of environmental protection and assigning itself the responsibility of protecting the global environment, BenQ has endeavored, and will steadily continue to endeavor, to construct recycling systems around the world so as to collect and recycle the used monitors from our customers.
Page 37
Area Country Details on the Service Center Czech RREMA lOOO IK, a.s. Bavorská 856 155 41 Praha 5 Česká republika Tel.: +420 224 454 224 Fax: +420 224 454 422 E-mail: info@remasystem.cz www.remasystem.cz Denmark Elretur A/S Tel.: +45 33 36 91 98 E-mail: elretur@elretur.dk Norway Elretur AS...
Page 38
Area Country Details on the Service Center Hungary ELECTRO-COORD Magyarország Kht. Márvány utca 18, H-1012 Budapest Tel.: (+36-1) 224-7730, Fax: (+36-1) 224-7739 E-mail: info@electro-coord.hu www.electro-coord.hu Ireland Midia Ltd Tel.: +353-1-4199733 Fax: +353-1-4565120 Unit B Montone Business Park Oak Road Dublin 12 Luxembourg Ecotrel 7, rue Alcide de Gasperi...
Page 39
Area Country Details on the Service Center Slovakia SEWA, a.s. Račianska č. 71 831 02 Bratislava Tel.: + 421 (0)2 4910 6811 Fax: + 421 (0)2 4910 6819 E-mail: sewa@sewa.sk Spain ECOASIMELEC C/ Orense, 62, 28020 Madrid Tel.: + 34914170890 Fax: +34915550362 Sweden El-kretsen AB...
Page 40
Area Country Details on the Service Center Bulgaria Most Computers Blv. 240 Shipchenski Prohod 1111 Sofia Bulgaria Tel.: +359 2 91 823 www.mostcomputers.com www.most.bg Latvia SIA "EMP" Latvia, Riga, Kr.Barona 133, LV-1012 Mob.: (+371) 9468536 Tel.: (+371) 7291206 Fax: (+371) 7291206 www.emp.lt Lithuania Novitera...
Page 41
Area Country Details on the Service Center Poland CCR Polska sp. z o.o. ul. Solec 38 PL 00-394 Warszawa Tel.: +48 22 2138 200 Fax: +48 22 2138 201 www.erp-recycling.org EMP Electronik Recycling Poland Polska. Gdansk. Wrzeszcz ul. Czarna 1 Tel.: +48 58 345 42 18 Fax: +48 58 345 42 18 www.recycling-system.pl/gb/index.php...
• All BenQ monitors and projectors come with user manuals on compact discs which could be easily read by commercial software such as Adobe Reader via a connected computer system.
FCC Statements Federal Communications Commission (FCC) Notice (U.S. Only) WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 44
化学物質の含有状況により、次の 2 種類の表示マークが存在します。 当該化学物質が指定の含有基値を超えている場合の製品に付与す るマーク。 含有マーク 当該化学物質が、含有マークの除外事項を除き指定の含有基準値 以下である製品に、メーカーが任意で表示することが出来るマー ク。 グリーンマーク • 弊社環境活動に関します情報をご確認いただく場合は www.BenQ.co.jp/environment をご参照くださ い。 • 製品情報につきましては www.BenQ.co.jp よりご確認ください。 • 日本工業規格番号 JIS C 0950 ( 通称:J-MOSS) に関します情報は、JEITA の Web サイト http://210.254.215.73/jeita_eps/jmoss200512.html をご参照下さい。 Japanese Industrial Standards No. JIS C 0950 (J-Moss) is a Japanese industrial standard of electrical and electronic equipment to mark the presence of the specific chemical substances on carton, catalog (user manual, printed materials, website etc.).
R Mark standards). G Mark •For more information about BenQ environmental activities, please visit www.BenQ.co.jp/environment. •For more information about BenQ products, please visit www.BenQ.co.jp. •For more information about JIS C 0950 (J-Moss), please visit JEITA's website http://210.254.215.73/jeita_eps/jmoss200512.html.
Page 46
China Energy Label 为了保护环境并达成节能减排之目的,本公司积极致力于产品节能之设计与制造,依据” 能源效率标识管理办法”及”计算机显示器能源效率标识实施规则” ,本产品之能效等级 符合国家标准 GB21520-2008 之 级标准。详细有关信息请查阅中国能效标识网 一 。 http://www.energylabel.gov.cn/ Energy Star ENERGY STAR Qualified LCD Monitor This product complies with the requirements of the USEPA ENERGY STAR program for Computer Monitors, Version 5.0. Regulatory Statements...
WEEE WEEE directive Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union. This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment.
Page 48
Direttiva WEEE Smaltimento di apparecchi elettrici ed elettronici nell'Unione Europea da parte di utenti privati. Questo simbolo sul prodotto o sulla confezione indica che esso non può essere smaltito come rifiuto domestico. È necessario smaltirlo restituendolo secondo lo schema di raccolta per il riciclaggio degli apparecchi elettrici ed elettronici.
Page 49
WEEE directive Verwijdering van afval van elektrische en elektronische apparaten door gebruikers in privé-huishoudens in de Europese Unie. Dit symbool op het product of op de verpakking geeft aan dat het niet als huishoudelijk afval mag worden verwijderd. U dient uw versleten apparatuur af te geven volgens het toepasselijke terugnameschema voor de recyclage van elektrische en elektronische apparaten.
Page 50
WEEE irányelv Az Európai Unióban a magánháztartások elektromos és elektronikus hulladékainak kezelésér l szóló irányelv. A terméken vagy a csomagoláson ez a szimbólum azt jelzi, hogy a termék nem tehet a háztartási hulladékok közé. A készüléket az elektronikus és elektromos hulladékokra vonatkozó visszavételi rendszerben kell visszajuttatnia.
Page 52
WEEE Smernica WEEE Nakladanie s elektrickými a elektronickými zariadeniami ur enými na likvidáciu používate mi v domácnostiach v rámci Európskej únie Tento symbol na výrobku, jeho príslušenstve alebo na jeho obale znamená, že tento výrobok nesmie by likvidovaný spolu s domovým odpadom.
Page 53
WEEE-direktiv Bortskaffelse af affald af elektrisk og elektronisk udstyr i husholdninger i Den Europæiske Union. Symbolet på produktet eller på emballagen angiver, at det ikke kan bortskaffes som affald fra husholdningen. Du skal bortskaffe udstyr ved at give det til indsamlingssteder, der kan genbruge elektrisk og elektronisk udstyr.
Page 54
WEEE-direktiv Användares avfall från elektrisk och elektronisk utrustning (WEEE) inom privata hushåll i den Europeiska unionen. Den här symbolen på produkten eller på förpackningen visar på att det här inte kan sorteras som hushållsavfall. Du måste göra dig av med utrustningen genom att lämna den vidare till den tillämpade återtagningsplanen för återvinning av elektrisk och elektronisk utrustning.För att få...