How to assemble your monitor hardware ..............6 How to detach the stand base .......................10 Getting the most from your BenQ monitor ..............11 Downloading the LCD Monitor driver files from the Internet ..........11 How to install the monitor on a new computer ................12 How to upgrade the monitor on an existing computer ..............13...
1. Getting started When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement. BenQ LCD Monitor Monitor Base Power Cord (Picture may differ from product supplied for your region.)
2. Getting to know your monitor Front view 1. Power button Back view 2. Control buttons 3. AC Power Input jack 4. Cable clip 5. HDMI socket 6. D-Sub socket 7. Lock switch 8. Headphone jack Above diagram may vary depending on the model. Getting to know your monitor Downloaded from ManualMonitor.com Manuals...
Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Attach the monitor base. V2210 / V2210 Eco Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty.
Page 7
(For V2410 / V2410 Eco) V2410 / V2410 Eco Orient and align the stand base socket with the end of the stand arm, then push them together. Tighten the thumbscrew on the bottom of the monitor base as illustrated. Gently attempt to pull them back apart to check that they have properly engaged.
Page 8
2. Connect the PC video cable To Connect the D-Sub Cable Connect the plug of the D-Sub cable (at the end without the ferrite filter) to the monitor video socket. Connect the other end of the cable (at the end with the ferrite filter) to the computer video socket.
Page 9
Picture may differ from product supplied for your region. Turn on the monitor by pressing the power button. Turn on the computer too, and follow the instructions in Getting the most from your BenQ monitor Section 4: on page 11 to install the monitor software.
V2410 / V2410 Eco surround and controls. 2. (For V2210 / V2210 Eco) Press the locking clips to V2210 / V2210 Eco detach the monitor base from the monitor stand arm.
4. Getting the most from your BenQ monitor To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ website (http://www.benq.com/support). See...
BenQ LCD Monitor is the first ever monitor to be connected to it. If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Next This will install the appropriate monitor driver files to your computer. 8. Click Close You may be prompted to restart your computer after the driver update is complete. Getting the most from your BenQ monitor Downloaded from ManualMonitor.com Manuals...
Next This will install the appropriate monitor driver files to your computer. 9. Click Close You may be prompted to restart your computer after the driver update is complete. Getting the most from your BenQ monitor Downloaded from ManualMonitor.com Manuals...
The Monitor Properties window will display. If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper drivers are already installed, and you need do nothing further. Cancel out of these property windows.
If you wish, you can always adjust the screen geometric settings manually using geometry menu items. To assist you in this endeavour, BenQ has provided a screen test image utility which you can use to check for screen color, grayscale and line gradient display. The utility is available on the BenQ website.
6. How to adjust your monitor The control panel : Adjusts vertical position, phase, horizontal position and pixel clock automatically. AUTO key: Activates OSD main menu and return to the previous menu or exit OSD. MENU key: For Up/Increase adjustment. The key is the hot key for Volume. Volume key: For Down/Decrease adjustment.
Hot key mode The monitor keys perform as hot keys to provide direct access to particular functions whenever the menu isn't currently displaying on-screen. Volume hot keys Press the key to display the Volume indicators. Further press the key will increase the volume, while the key will decrease the volume.
Main menu mode You can use the OSD (On Screen Display) menu to adjust all the settings on your monitor. Press the key to display the following main OSD menu. MENU There are five main OSD menus: 1. Display 2. Picture DISPLAY MODE: Standard 3.
Display menu 1. Press the key to display the main MENU menu. 2. Press the keys to select DISPLAY MODE: Standard and then press the DISPLAY ENTER to enter the menu. Auto Adjustment H. Position 3. Press the keys to move the V.
Page 22
H. Position Adjusts the horizontal 0 to 100 Press the keys to position of the screen image. adjust the value. V. Position Adjusts the vertical position 0 to 100 of the screen image. Pixel Clock Adjusts the pixel clock 0 to 100 frequency timing to synchronize with the analog input video signal.
Picture menu 1. Press the key to display the main MENU menu. 2. Press the keys to select PICTURE MODE: Standard and then press the PICTURE ENTER Brightness to enter the menu. Contrast Sharpness 3. Press the keys to move the Gamma highlight to a menu item and then press Color...
Page 24
- Press to enter the Color menu Color ENTER This Color menu is available only in the Standard mode. Normal Allows video and still Press the keys to photographs to be viewed select this option. with natural coloring. This is the factory default color. Bluish Applies a cool tint to the image and is factory pre-set...
Picture Advanced menu 1. Press the key to display the main MENU menu. 2. Press the keys to select PICTURE ADVANCED MODE: Standard and then press PICTURE ADVANCED Picture Mode Standard key to enter the menu. ENTER Senseye Demo Dynamic Contrast 3.
Page 26
Senseye Demo Displays the preview of • ON Press the keys to screen images under the • OFF change the settings. selected mode from Picture Mode. The screen will be divided into two windows; the left window demonstrates images of Standard mode, while the right window presents the images under the specified...
Page 27
Color Format Determines the color space Press the key to • RGB ENTER (RGB or YUV) based on the select this option. Press the • YUV following detected video keys to change signal: the settings. • D-Sub (VGA) from PC: The default Color Format is RGB.
Audio menu 1. Press the key to display the main MENU menu. 2. Press the keys to select AUDIO AUDIO MODE: Standard and then press the key to enter ENTER the menu. Volume Mute 3. Press the keys to move the Audio Select Auto Detect highlight to a menu item and then press...
System menu 1. Press the key to display the main MENU menu. 2. Press the keys to select SYSTEM MODE: Standard and then press the SYSTEM ENTER Input D-sub to enter the menu. OSD Settings DDC/CI 3. Press the keys to move the Auto Power off highlight to a menu item and then press Information...
Page 30
H. Position Adjusts the horizontal 0 to 100 Press the keys to position of the OSD menu. change the settings. V. Position Adjusts the vertical position 0 to 100 of the OSD menu. Display Time Adjusts the display time of •...
Page 31
HDMI Auto When this function is Press the key to select • ON ENTER Switch activated, HDMI port will be • OFF this option. Press the in the input auto select keys to change the loop.Otherwise, HDMI can settings. only be selected by input select or by hot key.
7. Troubleshooting Frequently asked questions (FAQ) The image is blurred: Read the instructions in Adjusting the screen resolution on page 34, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test.
Sound cannot be muted: • Restart your computer. • Update the graphics and/or audio driver. Need more help? If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: Support@BenQ.com. Troubleshooting Downloaded from ManualMonitor.com Manuals...
Model Native Resolution V2210 / V2210 Eco 1920 x 1080 V2410 / V2410 Eco 1920 x 1080 To take full advantage of LCD technology you should select the native resolution setting of your PC screen as described below.
Adjusting the screen refresh rate You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer.
Preset display modes Incoming display mode (Input timing) Resolution 21.5W 1920X1080 1920X1080 640x480@60Hz 640x480@75Hz 720x400@70Hz 800x600@60Hz 800x600@75Hz 832x624@75Hz 1024x768@60Hz 1024x768@75Hz 1152x870@75Hz 1280x720@60Hz 1280X960@60Hz 1280x1024@75Hz 1360x768@60Hz 1600x900@60Hz 1680x1050@60Hz 1920x1080@60Hz • Image disruption may occur as a result of signal frequency differences from graphic cards which do not correspond with the usual standard.
Recognizing the importance of environmental protection and assigning itself the responsibility of protecting the global environment, BenQ has endeavored, and will steadily continue to endeavor, to construct recycling systems around the world so as to collect and recycle the used monitors from our customers.
Page 38
Area Country Details on the Service Center Czech RREMA lOOO IK, a.s. Bavorská 856 155 41 Praha 5 Česká republika Tel.: +420 224 454 224 Fax: +420 224 454 422 E-mail: info@remasystem.cz www.remasystem.cz Denmark Elretur A/S Tel.: +45 33 36 91 98 E-mail: elretur@elretur.dk Norway Elretur AS...
Page 39
Area Country Details on the Service Center Hungary ELECTRO-COORD Magyarország Kht. Márvány utca 18, H-1012 Budapest Tel.: (+36-1) 224-7730, Fax: (+36-1) 224-7739 E-mail: info@electro-coord.hu www.electro-coord.hu Ireland Midia Ltd Tel.: +353-1-4199733 Fax: +353-1-4565120 Unit B Montone Business Park Oak Road Dublin 12 Luxembourg Ecotrel 7, rue Alcide de Gasperi...
Page 40
Area Country Details on the Service Center Slovakia SEWA, a.s. Račianska č. 71 831 02 Bratislava Tel.: + 421 (0)2 4910 6811 Fax: + 421 (0)2 4910 6819 E-mail: sewa@sewa.sk Spain ECOASIMELEC C/ Orense, 62, 28020 Madrid Tel.: + 34914170890 Fax: +34915550362 Sweden El-kretsen AB...
Page 41
Area Country Details on the Service Center Bulgaria Most Computers Blv. 240 Shipchenski Prohod 1111 Sofia Bulgaria Tel.: +359 2 91 823 www.mostcomputers.com www.most.bg Latvia SIA "EMP" Latvia, Riga, Kr.Barona 133, LV-1012 Mob.: (+371) 9468536 Tel.: (+371) 7291206 Fax: (+371) 7291206 www.emp.lt Lithuania Novitera...
Page 42
Area Country Details on the Service Center Poland CCR Polska sp. z o.o. ul. Solec 38 PL 00-394 Warszawa Tel.: +48 22 2138 200 Fax: +48 22 2138 201 www.erp-recycling.org EMP Electronik Recycling Poland Polska. Gdansk. Wrzeszcz ul. Czarna 1 Tel.: +48 58 345 42 18 Fax: +48 58 345 42 18 www.recycling-system.pl/gb/index.php...
• All BenQ monitors and projectors come with user manuals on compact discs which could be easily read by commercial software such as Adobe Reader via a connected computer system.
The model name is as cover page. Manufacturer's name, address, telephone & fax no. Name: BenQ Corporation Address: 16 Jihu Road, Neihu, Taipei 114, Taiwan TEL: + 886 2 2727 8899.is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating Electromagnetic compatibility (2004/108/EC) and Low Voltage Directive (2006/95/EC).
Page 45
化学物質の含有状況により、次の 2 種類の表示マークが存在します。 当該化学物質が指定の含有基値を超えている場合の製品に付与す るマーク。 含有マーク 当該化学物質が、含有マークの除外事項を除き指定の含有基準値 以下である製品に、メーカーが任意で表示することが出来るマー ク。 グリーンマーク • 弊社環境活動に関します情報をご確認いただく場合は www.BenQ.co.jp/environment をご参照くださ い。 • 製品情報につきましては www.BenQ.co.jp よりご確認ください。 • 日本工業規格番号 JIS C 0950 ( 通称:J-MOSS) に関します情報は、JEITA の Web サイト http://210.254.215.73/jeita_eps/jmoss200512.html をご参照下さい。 Japanese Industrial Standards No. JIS C 0950 (J-Moss) is a Japanese industrial standard of electrical and electronic equipment to mark the presence of the specific chemical substances on carton, catalog (user manual, printed materials, website etc.).
R Mark standards). G Mark •For more information about BenQ environmental activities, please visit www.BenQ.co.jp/environment. •For more information about BenQ products, please visit www.BenQ.co.jp. •For more information about JIS C 0950 (J-Moss), please visit JEITA's website http://210.254.215.73/jeita_eps/jmoss200512.html.
China Energy Label 为了保护环境并达成节能减排之目的,本公司积极致力于产品节能之设计与制造,依据” 能源效率标识管理办法”及”计算机显示器能源效率标识实施规则” ,本产品之能效等级 符合国家标准 GB21520-2008 之 级标准 (V2210 / V2210 Eco, V2410 / V2410 Eco)。详细有 一 关信息请查阅中国能效标识网 http://www.energylabel.gov.cn/ 。 Energy Star ENERGY STAR Qualified LCD Monitor This product complies with the requirements of the USEPA ENERGY STAR program for Computer Monitors, Version 5.0.
Page 48
WEEE WEEE directive Disposal of Waste Electrical and Electronic Equipment by users in private households in the European Union. This symbol on the product or on the packaging indicates that this can not be disposed of as household waste. You must dispose of your waste equipment by handling it over to the applicable take-back scheme for the recycling of electrical and electronic equipment.
Page 49
Direttiva WEEE Smaltimento di apparecchi elettrici ed elettronici nell'Unione Europea da parte di utenti privati. Questo simbolo sul prodotto o sulla confezione indica che esso non può essere smaltito come rifiuto domestico. È necessario smaltirlo restituendolo secondo lo schema di raccolta per il riciclaggio degli apparecchi elettrici ed elettronici.
Page 50
WEEE directive Verwijdering van afval van elektrische en elektronische apparaten door gebruikers in privé-huishoudens in de Europese Unie. Dit symbool op het product of op de verpakking geeft aan dat het niet als huishoudelijk afval mag worden verwijderd. U dient uw versleten apparatuur af te geven volgens het toepasselijke terugnameschema voor de recyclage van elektrische en elektronische apparaten.
Page 51
WEEE irányelv Az Európai Unióban a magánháztartások elektromos és elektronikus hulladékainak kezelésér l szóló irányelv. A terméken vagy a csomagoláson ez a szimbólum azt jelzi, hogy a termék nem tehet a háztartási hulladékok közé. A készüléket az elektronikus és elektromos hulladékokra vonatkozó visszavételi rendszerben kell visszajuttatnia.
Page 52
9''' Regulatory Statements Downloaded from ManualMonitor.com Manuals...
Page 53
WEEE Smernica WEEE Nakladanie s elektrickými a elektronickými zariadeniami urþenými na likvidáciu používate mi v domácnostiach v rámci Európskej únie Tento symbol na výrobku, jeho príslušenstve alebo na jeho obale znamená, že tento výrobok nesmie by likvidovaný spolu s domovým odpadom.
Page 54
WEEE-direktiv Bortskaffelse af affald af elektrisk og elektronisk udstyr i husholdninger i Den Europæiske Union. Symbolet på produktet eller på emballagen angiver, at det ikke kan bortskaffes som affald fra husholdningen. Du skal bortskaffe udstyr ved at give det til indsamlingssteder, der kan genbruge elektrisk og elektronisk udstyr.
Page 55
WEEE-direktiv Användares avfall från elektrisk och elektronisk utrustning (WEEE) inom privata hushåll i den Europeiska unionen. Den här symbolen på produkten eller på förpackningen visar på att det här inte kan sorteras som hushållsavfall. Du måste göra dig av med utrustningen genom att lämna den vidare till den tillämpade återtagningsplanen för återvinning av elektrisk och elektronisk utrustning.För att få...