Setting The Stop Code (Stop Code) - Sony SRW-5000 Operation Manual

For detail on the procedure for DMC editing, see "6-2-1
DMC Editing" on page 125.
4-2-8 Setting the Stop Code (STOP
CODE)
You can select the stop code detection mode (recording/
confirmation/deletion), and adjust the stop position when a
stop code is detected.
To call up the STOP CODE menu screen
Press the ALT/[F8] (STOP CODE) buttons in the HOME
menu.
L T C I N T R P
00
T C R
D E T E C T
B E E P
o f f
U B 0 0 0 0 0 0 0 0
D E T E C T
S T O P
o f f
D E T E C T
A D J U S T
o f f
R E C
A D J U S T
o f f
Note
If DETECT STOP is set to "ON", "D-STOP" appears at
the side of the cassette indication, as shown in the
following figure.
s
T A P E L O C K
L T C I N T R P D F
00 02
T C R
D E T E C T
H
B E E P
o f f
U B 0 0 0 0 0 0 0 0
D E T E C T
S T O P
o f f
D E T E C T
A D J U S T
o f f
R E C C O D E C O D E
A D J U S T R E C E R A S E
o f f o f f o f f
To detect stop codes: [F2], [F3]
When playing a tape on which stop codes are recorded,
you can select four different operation modes, according to
the settings of the [F2] (DETECT BEEP) button and [F3]
(DETECT STOP) button, as follows.
[F2] (DETECT [F3] (DETECT
BEEP) button STOP) button
OFF OFF
52
4-2 HOME Menu
T A P E L O C K
D F F 2
02 39 18
H M S F
C O D E C O D E E X I T
R E C E R A S E
o f f o f f
F 2
39 18
M S F
S E T 0 1 3 0 0 0 0 0
D-STOP
S S
S T I L L H D C A M - S R
E X I T
R E M A I N : 0 1 H 0 6 M
!
D-STOP
VTR operation when stop
code is detected
No operation
[F2] (DETECT
BEEP) button
OFF
ON
ON
The tape transport modes and speed ranges in which stop
codes can be detected are as follows.
Transport mode
and speed
NORMAL PLAY
VAR, SHUTTLE
(0 to less than ±8
times normal
speed)
REC, EDIT, JOG,
CUE UP,
PREROLL,
SHUTTLE (±8
times normal
speed or more)
Note
In VAR mode, stop codes cannot be detected at ±0.03
times normal speed.
Adjusting the stop position when a stop
code is detected: [F4]
When a stop code is detected, you can adjust the position
at which the tape transport stops in the direction from the
normal stop position toward the SOM point, within the
range of 0 to 150 frames, in frame units.
T C
3,5
1
Press the HOME button.
The HOME menu screen appears.
[F3] (DETECT
VTR operation when stop
STOP) button code is detected
ON Stops (for NORMAL PLAY
only)
OFF A beeper sounds for 1
second
ON Stops (for NORMAL PLAY
only) and simultaneously a
beeper sounds for 1
second
Detected Beeper
timing
Yes When read
three times
Yes When read
twice
No No
operation
1
2 4
Stop timing
Set by [F4]
(DETECT
ADJUST)
No operation
No operation