Toyota corolla; toyota auris; toyota auris hybrid (24 pages)
Summary of Contents for Toyota TNS 300
Page 1
T O Y O T A N A V I G A T I O N S Y S T E M LC 120 (LHD) EINBAUANLEITUNG INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION FÜR - FOR - POUR ** J12 * L TEILENUMMER - PART NUMBER - NUMERO DE PIECE NAVIGATIONSSATZ 08545-00805 NAVIGATION KIT KIT DE NAVIGATION Pdf for ADPA N3LJ12/J-0-1.pdf TOYOTA MOTOR CORPORATION...
LAND CRUISER TNS 300 PRECAUTIONS PLEASE READ THOROUGHLY THESE PRECAUTIONS FOR THIS SYSTEM INSTALLATION • Be sure to disconnect the negative (-) • Before drilling a hole, check that the rear of the mounting wall is clear. lead from the battery terminals.
LAND CRUISER TNS 300 TNS 300 NAVIGATION SYSTEM ASSY 08545-00805 Description COMPUTER WIRE HARNESS GPS ANTENNA NAVIGATION DISC (*1) COMPUTER BRACKET BOLT (M5 x 8) CORD CLAMP FOAM TAPE WIRE TIE EARTH PLATE ADHESIVE TAPE *1:NAVIGATION DISC (DVD-ROM) is not included in the navigation kit.
LAND CRUISER TNS 300 VEHICLE DISASSEMBLY Remove the console finish panel (L) Console finish panel (L) and (R). Clips x 3 Clips x 4 Figure 1 Console finish panel (R) Remove the integration panel (L) and Integration panel (L) Integration panel (R) (R).
Page 8
LAND CRUISER TNS 300 Remove the heater control panel. Heater control panel Bolt Figure X Figure 4 Clips x 4 Bolts x 5 Remove the front door scuff plate (R). Hooks x 11 Front door scuff plate (R) Figure X Figure 5 Remove the cowl side panel (R).
Page 9
LAND CRUISER TNS 300 Remove the passenger’s seat. Covers x 4 Passenger’s seat Bolts x 4 Figure X Figure 7 Remove the instrument panel under Clips x 3 cover (R). Screw Instrument panel under cover (R) Figure X Figure 8...
Page 10
LAND CRUISER TNS 300 10. Remove the foot rest. Clips x 2 Foot rest Figure X Figure 10 11. Remove the front door scuff plate (L). Hooks x 11 Front door scuff plate (L) Figure X Figure 11 12. Remove the cowl side panel (L).
Page 11
LAND CRUISER TNS 300 13. Remove the instrument panel under cover (L). Screw Clips x 2 Figure X Figure 13 Instrument panel under cover (L) 14. Remove the instrument panel cluster moulding (L). Clips x 2 Instrument panel cluster moulding (L)
Page 12
LAND CRUISER TNS 300 16. Remove the front console panel side cover (R). Hooks x 2 Hook Front console panel side cover (R) Figure X Figure 16 17. Remove the meter cluster panel. Clips x 2 Clips x 2 Figure X...
LAND CRUISER TNS 300 GPS ANTENNA INSTALLATION FOAM TAPE CUT PROCEDURES Cut the foam tape into 3 large pieces, 9 middle pieces and 12 small Foam tape pieces as shown in the illustration. <Large piece> • For computer • For computer corner cover <Middle piece>...
Page 14
LAND CRUISER TNS 300 Remove the release paper of the earth plate and apply the adhesive GPS antenna tape Attach the earth plate to the meter cluster panel as shown and mount the Adhesive tapes x 2 GPS antenna to the earth plate...
LAND CRUISER TNS 300 WIRE HARNESS INSTALLATION Remove the driver side J/B. Driver side J/B Nut x 2 Figure 23 Bolt Route the wire harness and anten- na cord as shown in the illustration. Antenna cord Wire harness Vehicle side tie...
Page 16
LAND CRUISER TNS 300 Route the speed sensor wire Wire harness speed sensor wire shown in the illustration, and secure the speed sensor wire using the foam tapes Foam tape x 3 Figure 26 Disconnect the 16P connector (White) 16P (White)
Page 17
LAND CRUISER TNS 300 Route the reverse sensor wire Foam tape x 6 shown in the illustration, and secure the 13P (White) reverse sensor wire using the foam tapes Disconnect the 13P connector (White). Connector block Wire harness reverse sensor wire...
Page 18
LAND CRUISER TNS 300 12. Connect the TX- sensor wire (Yellow / 12P (White) Black) of the wire harness to the 12P connector (White) terminal 9 har- 10 9 ness. Wire harness side 12P 13. Connect the TX+ sensor wire (Yellow)
Page 19
LAND CRUISER TNS 300 19. Route the wire harness and anten- Antenna cord Foam tapes x 7 na cord to the computer installa- tion area and attach them with foam tapes 20. Secure the extra length of the wire har-...
LAND CRUISER TNS 300 COMPUTER INSTALLATION Fit the computer brackets to the Computer brackets x 2 Bracket installing position computer using the bolts Computer Attach the rest of the adhesive tapes used to fix install the plate, to the Center...
Page 21
LAND CRUISER TNS 300 Route the Vehicle wire harness. Vehicle slit Vehicle slit Vehicle wire harness Figure 38 Connect 1P connector (GPS antenna ), 8P connector and 13P connector (wire harness ) to the computer Computer Figure 39 LAND CRUISER (LHD) - 21...
Page 22
LAND CRUISER TNS 300 CAUTION : Put the computer after adjusting it in a horizontal posi- Computer tion. Install the computer on the prede- termined position. CAUTION : When affixing the com- puter , make sure to carefully wipe off any dirt, moisture or oil from the surface of the location where it is to be affixed.
Press the NAVI switch and confirm that the navigation screen is displayed. Adjust the volume by following the section on "Adjusting the Volume of the Guide Voice" in the TNS 300 Owner's Manual, and confirm that the sound from the speakers changes.
LAND CRUISER TNS 300 FINAL CHECK RESTORATION WORK Return all vehicle parts that have been removed to their original locations. Especially make sure to attach trim and other interior materials properly so that they do not have a detrimental effect on the function of the vehicle.