Toyota TNS 300 Installation Instructions Manual
Hide thumbs
Also See for TNS 300:
- Installation instructions manual (38 pages) ,
- Installation instructions manual (23 pages) ,
- Installation instructions manual (31 pages)
Related Manuals for Toyota TNS 300
Summary of Contents for Toyota TNS 300
- Page 1 T O Y O T A N A V I G A T I O N S Y S T E M Yaris (RHD) - MMC INSTALLATION INSTRUCTIONS ** P1 * R (Production date 12/02 and 02/03) PART NUMBER 08545-52800 NAVIGATION KIT Manual Ref. Nr. N3RP1/W-2-0 TOYOTA MOTOR CORPORATION...
- Page 3 Yaris (P1) TNS 300 Revision Record Rev. N Date Page Picture Update Deleted steps N3RP1/W-2-0 05-2005 20-pole connector / pin 19 Yaris (RHD) - 3 05-05...
-
Page 4: Precautions
Yaris (P1) TNS 300 PRECAUTIONS PLEASE READ THOROUGHLY THESE PRECAUTIONS BEFORE THE INSTALLATION ! • Protect your car with fender cov- • Be sure to disconnect the negative (-) lead from the battery terminals. ers, seat and so on. • Use the correct tool when tight- •... -
Page 5: Table Of Contents
Yaris (P1) TNS 300 TABLE OF CONTENTS Precautions ..................................Application Charts ................................6, 7 Component Parts ................................Required Parts ................................Wiring Connection ................................Installation Overview ..............................Vehicle Disassembly ............................... Installation of Computer ..............................Wire Harness Installation ............................... Installation of GPS Antenna ............................ -
Page 6: Application Charts
p. 1/2... - Page 7 p. 2/2...
-
Page 8: Component Parts
Yaris (P1) TNS 300 COMPONENT PARTS 08545-52800 Part name Quantity COMPUTER WIRE HARNESS GPS ANTENNA COMPUTER BRACKET BOLT (M5x8) WIRE CLAMP FOAM TAPE WIRE TIE EARTH PLATE BUTYL TAPE 05-05 Yaris (RHD) - 8... -
Page 9: Required Parts
Yaris (P1) TNS 300 REQUIRED PARTS DVD-ROM To be ordered separately. Please refer to the list of available DVD-ROM for TNS300 Navigation System (Access to accessories). OWNER’S MANUAL To be ordered separately. Yaris (RHD) - 9 05-05... -
Page 10: Wiring Connection
Yaris (P1) TNS 300 WIRING CONNECTION Connection Method: Splicing Connector (Speed Sensor Wire) Multi Display Splicing Connector (Reverse Sensor Wire) Audio Assembly GPS-antenna Vehicle Wire harness Splicing Connector Splicing Connector (TX+ Wire) (TX- Wire) Part name COMPUTER WIRE HARNESS GPS ANTENNA WIRE... -
Page 11: Installation Overview
Yaris (P1) TNS 300 INSTALLATION OVERVIEW GPS Antenna Splicing connectors WIRE HARNESS SUB-ASSEMBLY - SPEED LINE (VIOLET/WHITE) WIRE HARNESS ANTENNA WIRE WIRE HARNESS REVERSE SENSOR WIRE (RED/BLUE) Yaris (RHD) - 11 05-05... -
Page 12: Vehicle Disassembly
Yaris (P1) TNS 300 VEHICLE DISASSEMBLY Remove the glove compartment door assembly : Hook (2x) Fig. 1 Remove the instrument cluster finish panel : Clip (2x) : Hook (6x) Fig. 2 FOR ANALOG METER MODELS Remove combination meter assembly : Screw (2x) Fig. - Page 13 Yaris (P1) TNS 300 FOR DIGITAL METER MODELS Remove combination meter assembly : Screw (4x) Fig. 4 Remove the front ashtray Fig. 5 Remove the control knobs and the centre cluster panel : Screw (3x) Fig. 6 Yaris (RHD) - 13...
- Page 14 Yaris (P1) TNS 300 Remove the audio assembly : Screw (4x) Fig. 7 Remove the centre lower cover : Hook (1x) : Clip (2x) : Clips (1x) Fig. 8 Remove the front pillar garnish : Clip (2x) Fig. 9 05-05...
- Page 15 Yaris (P1) TNS 300 10. Remove the speaker grill : Hook (5x) Fig. 10 11. Remove the instrument panel speaker : Screw (2x) Fig. 11 12. Remove the kick panel (L) and the front door scuff plate (L) : Hook (3x) : Clip (5x) Fig.
- Page 16 Yaris (P1) TNS 300 13. Remove the passenger seat : Bolt (4x) : Cover (2x) NOTE Remove and discard the storage box underneath the seat (if equipped). CAUTION Fasten the bolt with specified torque when reassembling. Fig. 13 05-05 Yaris (RHD) - 16...
-
Page 17: Installation Of Computer
Yaris (P1) TNS 300 INSTALLATION OF COMPUTER Slit the carpet at the computer installa- 250mm tion position. 60mm 60mm Centre Fig. 14 Remove the carpet and drill two pre- holes (Ø4mm) for screws Punch Drill File , at the position shown. - Page 18 Yaris (P1) TNS 300 Cut and roll some tape and apply it to the body at the position shown in the illustration. 40mm 10mm CAUTION Apply the tape to fill the clearance between the computer bracket the body. Centre Fig. 16 Install the computer bracket (2x).
- Page 19 Yaris (P1) TNS 300 Restore the carpet. Bracket Installing Position Fit the computer to the computer bracket using the set bolts : Bolt (M5x8) (4x) Fig. 18 Yaris (RHD) - 19 05-05...
-
Page 20: Wire Harness Installation
Yaris (P1) TNS 300 WIRE HARNESS INSTALLATION Cut the foam tape into 3 large pie- ces and 16 small pieces as shown in the illustration. Fig. 19 WIRE SPLICING CONNECTOR INSTRUCTIONS Remove appropriate amount of tape wrapping the vehicle side harness to be connected. - Page 21 Yaris (P1) TNS 300 Match the length of the vehicle harness ,speed sensor wire and wire har- ness , and fix them using a wire tie at 100mm from the end. Fig. 22 Route the wire harness and the 300mm...
- Page 22 Yaris (P1) TNS 300 REVERSE SENSOR WIRE INSTALLA- TION Route the reverse sensor wire of the wire harness to the glovebox com- partment. Fig. 25 Locate and disconnect the connector (see table next page). Fig. 26 05-05 Yaris (RHD) - 22...
-
Page 23: Pole Connector / Pin
Yaris (P1) TNS 300 Turn the connector so that the wires face you and the tab is on top. Connect the reverse sensor wire (red/blue) of the wire harness to the wire. See table below for correct connection. Reconnect the connector... - Page 24 Yaris (P1) TNS 300 10. Affix the wire harness to the vehicle using foam tape Fig. 28 TX SENSOR WIRE INSTALLATION / CONNECTION TO AVC-LAN 11. Locate the 12P audio connector (AVC-LAN). Fig. 29 TX SENSOR WIRE INSTALLATION / CONNECTION TO AVC-LAN...
- Page 25 Yaris (P1) TNS 300 Connect the vehicle side 10P connec- tor to the wire harness Tie up the excess part of the wire har- ness , reverse sensor wire , and speed sensor wire , and affix them to the vehicle using foam tape at the position shown.
-
Page 26: Installation Of Gps Antenna
Yaris (P1) TNS 300 INSTALLATION OF GPS ANTENNA Refit the audio assembly : Screw (4x) Fig. 33 Connect the female 8P connector of the vehicle wire harness to the male 8P connector of the wire harness Connect the female 8P connector of the... - Page 27 Yaris (P1) TNS 300 Cut one butyl tape into 2 equal sized pieces. Fig. 36 Remove the release paper of the earth plate and the butyl tape Apply the butyl tape to the adhesive side of the earth plate Fig. 37...
- Page 28 Yaris (P1) TNS 300 Attach the earth plate to the instru- ment cluster as shown and mount the GPS antenna to the earth plate Fix the antenna wire using the foam tape (2x). CAUTION Clean the installation position surface before attaching the earth plate Fig.
- Page 29 Yaris (P1) TNS 300 FOR DIGITAL METER MODELS Refit the combination meter assembly : Screw (4x) Fig. 40 Refit the instrument cluster finish panel : Clip (2x) : Hook (6x) Fig. 41 ENSURE THAT ALL REMOVED CONNECTORS ARE PUT BACK CORRECTLY.
-
Page 30: Installation Of Navigation Disc
Yaris (P1) TNS 300 INSTALLATION OF NAVIGATION DISC Die Batterie anschließen und den Zündschalter in die Stellung ACC dre- hen. Den Auswurfschalter am Computer nach links schieben, um den Schlitz zum Einlegen der Disc zu öffnen. Die Navigations-Disc mit dem Label nach oben in den Schlitz einlegen. -
Page 31: Post-Installation Inspection
4. Perform the “auto-compensation” procedure by following the section on “When Tires are Replaced” in the TNS300 Owner’s Manual. When an abnormality is suspected, perform troubleshooting based on the “Toyota Genuine Navigation System Service Manual”. REASSEMBLING Return all vehicle parts that have been removed to their original locations. Especially make sure to attach trim and other inte- rior materials properly so that they do not have a detrimental effect on the function of the vehicle. - Page 32 GENUINE PARTS...