Table of Contents
Advertisement
v
i
ent
nstallation
v
:
enting
The Vintage™ gas stove has been tested and listed as
a direct vent heater system by OMNI-Test Laboratories,
Beaverton, Oregon and is recommended for use with
Security™ Secure Vent pipe*.
Important:
• Read all instructions carefully before starting the instal-
lation. Failure to follow these instructions may create a
fire or other safety hazard, and will void the warranty.
Be sure to check for specific clearances to combustible
requirements on page 7. Do not extend the venting sys-
tem vertically or horizontally in excess of the distance
prescribed on page 15. Consult your local building codes
before beginning the installation.
• Always maintain the proper air spaces between the
vent pipe and nearby combustibles to prevent a fire
hazard. Do not fill air spaces with insulation. Be sure to
check the vent termination clearance requirements from
decks, windows, soffits, gas regulators, air supply inlets,
and public walkways, as specified in these installation
instructions on page 16 and local building codes.
• This gas appliance and vent system must be vented
directly to the outside of the building, and never be
attached to a chimney serving a separate solid fuel or
gas-burning appliance. Each direct vent gas appliance
must use its own separate vent system. Common vent
systems are prohibited.
• The Vintage is recommended for use with Security™
Secure Vent pipe*. The appliances, and vent manufactur-
ers warranties will be voided, and serious fire, health, or
other safety hazards may result from any of the following
actions:
• Installation of any damaged direct vent compo-
nent.
• Unauthorized modification of the direct vent sys-
tem.
• Installation of any vent component part not approved
or manufactured by the approved vent manufac-
turer.
• Installation other than as instructed by Lennox Hearth
Products and vent manufacturers instructions.
r
m
h
esidential and
obile
These are the minimum pieces required. Other parts may
be required for your particular installation.
* Other approved chimney brand is Simpson Dura-Vent DV-GS.
i
:
ome
nstallations
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Minimum Components for Horizontal Installation:
Horizontal Termination Kit which includes:
• 1 6-5/8"x 6" Black Pipe
• 1 Riser Vent Terminal
• 1 Wall Penetration Heat Shield (Wall Thimble) (2 pcs)
• 1 Decorative Wall Trim (black)
• 1 Tube Mill-Pac
• Screws
Optional Components:
• 4 5º Elbow
• Vinyl Siding Shield for Riser Vent Terminal
• Vent Guard
• Snorkel Termination (36")
• Snorkel Termination (14")
• Wall Penetration Heat Shield
Vent Considerations:
Twist-lock procedure: Four indentations on female ends of
pipes and fittings are designed to slide straight onto male
ends of adjacent pipes and fittings by orienting the four pipe
indentations so they match and slide into the four entry slots.
Push pipe sections completely together, then twist-lock one
section clockwise approximately one-quarter turn until the
two sections are fully locked. The female locking lugs will not
be visible from the outside on the pipe or fittings. They may
be located by examining the inside of the female ends.
Supports: Horizontal runs of vent must be supported every
3 feet. Wall straps are available for this purpose.
Pipe Sealing: If Simpson Dura-Vent pipe is used, the pipe
must be sealed as follows: seal both the inner and outer
pipes with a high temperature silicone sealant rated for at
least 600ºF (commonly know as "RTV"). Run a 1/8" bead
of silicone around outside of male end of outer sleeve. Run
a 1/8" bead of silicone about 1/4" from the end of the male
inner pipe, which is found in the pipe to be attached above.
Twist-lock the pipes or fittings together.
Sealant
Figure 19
Female Locking
Male
Locking
Lugs
11
Advertisement
Table of Contents
