Table of Contents
Advertisement
Gas Conversion Kits
WARNING: THIS CONVERSION KIT SHALL BE IN-
STALLED BY A QUALIFIED SERVICE AGENCY IN AC-
CORDANCE WITH THE MANUFACTURER'S INSTRUC-
TIONS AND ALL APPLICABLE CODES AND REQUIRE-
MENTS OF THE AUTHORIZED AGENCY HAVING JU-
RISDICTION. IF THE INFORMATION IN THESE IN-
STRUCTIONS ARE NOT FOLLOWED EXACTLY, A FIRE,
EXPLOSION OR PRODUCTION OF CARBON MONOX-
IDE MAY RESULT CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR LOSS OF LIFE. THE INSTAL-
LATION IS NOT PROPER AND COMPLETE UNTIL THE
OPERATION OF THE CONVERTED APPLIANCE IS
CHECKED AS SPECIFIED IN THE OWNER INSTRUC-
TIONS SUPPLIED WITH THE KIT.
In Canada
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENT AUX RECOMMANDATIONS
DES AUTORITÉS PROVINCIALES AYANT
JURIDICTION ET CONFORMÉMENT AUX
EXIGENCES DU CODE D'INSTALLATION CAN1-
B149.1 ET.2.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to the
use of another. These kits contain all the nec-
essary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
Kit part numbers are listed here and the steps
that follow detail the conversion procedure.
14
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION
SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SERVICE
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET
TOUTES EXIGENCES ET CODES APPLICABLES DE
L'AUTORISÉS AVOIR LA JURIDICTION. SI L'INFORMATION
DANS CETTE INSTRUCTION N'EST PAS SUIVIE
EXACTEMENT, UN FEU, EXPLOSION OU PRODUCTION DE
PROTOXYDE DE CARBONE PEUT RÉSULTER LE DOMMAGES
CAUSER DE PROPRIÉTÉ, PERTE OU BLESSURE
PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE DE SERVICE
EST ESPONSABLE DE L'INSTALLATION PROPRE DE CET
ÉQUIPMENT. L'INSTALLATION N'EST PAS PROPRE ET
COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL
CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS
DANS LES INSTRUCTIONS DE PROPRIÉTAIRE
PROVISIONNÉES AVEC L'ÉQUIPEMENT.
M
i
i l l
o v
t l
S
T I
S
s y
e t
m
N
t a
r u
l a
o T
P
o r
a p
e n
G
s a
C
o
v n
M
o
e d
s l
U
t i n
y T
e p
L
S
B
- V
6 3
8 2
m
l i
v i l
t l o
L
S
B
- V
2 4
8 2
m
l i
v i l
t l o
l E
c e
r t
n o
c i
S
T I
S
s y
e t
N
t a
r u
l a
o T
P
o r
a p
e n
G
s a
C
o
v n
M
o
e d
s l
U
t i n
y T
e p
L
S
B
- V
6 3
8 2
l e
c e
r t
n o
c i
L
S
B
- V
2 4
8 2
l e
c e
r t
n o
c i
Step 1. Turn off the gas supply to the appli-
ance. Remove the front glass door (if used)
from the appliance. Access the control com-
partment.
Step 2. Carefully remove the logs. Exercise
care as not to break the logs.
Step 3. Locate the screw securing the burner.
Remove the burner and retain the securing
screw.
Millivolt Appliances
Step 4. SIT Systems - Refer to Figure 25 and
the instructions provided with the kit. Using a
Torx T20, remove and discard the three pres-
sure regulator mounting screws.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
s
-
M
P
o r
a p
e n
r e
i s
n o
K
s t i
M
o
e d
s l
a C
l a t
g o
N
. o
H
8 5
4 1
L
S
B
- V
6 3
8 2
L
S
B
- V
2 4
8 2
H
8 5
4 1
l E
m
s
-
P
o r
a p
e n
r e
i s
n o
K
s t i
M
o
e d
s l
a C
l a t
g o
N
. o
L
S
B
- V
6 3
H
8 5
5 1
L
S
B
- V
2 4
H
8 5
5 1
Remove the pressure regulator, spring, pop-
pet, diaphragm and bushing. Discard all re-
moved components. Ensure the rubber gasket
installed on the back of the replacement pres-
sure regulator is properly positioned and install
the new pressure regulator using the new screws
supplied with the kit. Tighten screws to 25 In.
lb. torque.
Pressure
Regulator
Figure 25
i
i l l
o v
t l
S
T I
S
s y
e t
m
s
-
o t
N
t a
r u
l a
G
s a
C
o
v n
r e
i s
n o
K
s t i
U
t i n
y T
e p
a C
l a t
g o
N
. o
m
l i
v i l
t l o
H
8 5
2 1
m
l i
v i l
t l o
H
8 5
2 1
c e
r t
n o
c i
S
T I
S
s y
e t
m
s
-
o t
N
t a
r u
l a
G
s a
C
o
v n
r e
i s
n o
K
s t i
U
t i n
y T
e p
a C
l a t
g o
N
. o
8 2
l e
c e
r t
n o
c i
H
8 5
3 1
8 2
l e
c e
r t
n o
c i
H
8 5
3 1
Remove
These
Components
Advertisement
Table of Contents
