Gas Conversion Kits - Lennox Hearth Products Spectra LSS-35CN Installation Instructions Manual

GAS CONVERSION KITS

WARNING: THIS CONVERSION KIT SHALL BE
INSTALLED BY A QUALIFIED SERVICE AGENCY
IN ACCORDANCE WITH THE MANUFACTURER'S
INSTRUCTIONS AND ALL APPLICABLE CODES
AND REQUIREMENTS OF THE AUTHORITY HAVING
JURISDICTION. IF THE INFORMATION IN THESE
INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A
FIRE, EXPLOSION OR PRODUCTION OF CARBON
MONOXIDE MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
THE INSTALLATION IS NOT PROPER AND COM-
PLETE UNTIL THE OPERATION OF THE CONVERTED
APPLIANCE IS CHECKED AS SPECIFIED IN THE
OWNER INSTRUCTIONS SUPPLIED WITH THE KIT.
THE QUALIFIED SERVICE AGENCY PERFORMING
THIS INSTALLATION ASSUMES RESPONSIBILITY
FOR THIS CONVERSION.
In Canada
THE CONVERSION SHALL BE CARRIED OUT
BY A MANUFACTUREER'S AUTHORIZED
REPRESENTATIVE, IN ACCORDANCE
WITH THE REQUIREMENTS OF THE
MANUFACTURER, PROVINCIAL OR
TERRITORIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE
WITH THE REQUIREMENTS OF THE
CAN/CGA-B149.1 OR CAN/CGA-B149.2
INSTALLATION CODES.
LA CONVERSION DEVRA ÊTRE
EFFECTUÉE CONFORMÉMENT AUX
RECOMMANDATIONS DES AUTORITÉS
PROVINCIALES AYANT JURIDICTION ET
CONFORMÉMENT AUX EXIGENCES DU
CODE D'INSTALLATION CAN1-B149.1 ET.2.
This Gas Conversion Kit contains all of the
necessary components needed to complete
the conversion of an appliance from the use
of one type of gas to the use of another,
including labeling that must be affixed to
ensure safe operation.
ALWAYS REFER TO THE APPLIANCE
INSTALLATION AND CARE AND OPERATION
DOCUMENTS BEFORE COMPLETING A
CONVERSION. ALL WARNINGS, CAUTIONS
AND DETAILED INSTRUCTIONS CONTAINED
THEREIN ARE APPLICABLE HERE.
Note: After converting the valve and
gas components, refer to the appliance
installation and care and operation
instructions to adjust the air shutter opening
for the gas type used.
Kit part numbers are listed here and the
following steps detail the conversion procedure.
30
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION
SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE
SERVICE CONFORMÉMENT AUX INSTRUCTIONS DU
FABRICANT ET TOUTES EXIGENCES ET CODES APPLI-
CABLES DE L'AUTORISÉS AVOIR LA JURIDICTION. SI
L'INFORMATION DANS CETTE INSTRUCTION N'EST PAS
SUIVIE EXACTEMENT, UN FEU, EXPLOSION OU PRODUC-
TION DE PROTOXYDE DE CARBONE PEUT RÉSULTER
LE DOMMAGES CAUSER DE PROPRIÉTÉ, PERTE OU
BLESSURE PERSONNELLE DE VIE. L'AGENCE QUALI-
FIÉE DE SERVICE EST ESPONSABLE DE L'INSTALLATION
PROPRE DE CET ÉQUIPMENT. L'INSTALLATION N'EST
PAS PROPRE ET COMPLÉTE JUSQU'À L'OPÉRATION
DE L'APPAREIL CONVERTI EST CHÉQUE SUIVANT LES
CRITÈRES ÉTABLIS DANS LES INSTRUCTIONS DE PRO-
PRIÉTAIRE PROVISIONNÉES AVEC L'ÉQUIPEMENT.
Natural To Propane Gas Conversion Kits
Models Catolog No.
LSS-35
LSS-40
CAUTION: The gas supply shall be shut off
prior to disconnecting the electrical power,
before proceeding with the conversion.
Step 1. Turn off the gas supply to the
appliance. Remove the front frame and glass
door from the appliance. Access the control
compartment.
Step 2. Carefully remove the logs. Exercise
care as not to break the logs.
Step 3. Remove the grate.
See Figure 51 for Step 4 part removal details.
Burner Clamp
Securing Screw
Burner Clamp
Front Burner
Securing Screw
Figure 51
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Propane To Natural Gas Conversion Kit
Models
H7852 LSS-35
H7853 LSS-40
Step 4
a. Remove the front baffle by removing the
two securing screws.
b. Remove the two screws securing the end
tabs of the front burner. Remove the front
burner.
c. Remove the two screws securing each
of the rear burner clamps. Remove the rear
burner.
Rear Burner
Front Baffle
Front Burner
Burner Assembly
Catolog No.
H7854
H7855
Front Baffle
Securing Screw