Universal Remote Control UR4-P360SI Operating Instructions

Operating Instructions
Introduction
1
For 4 Function The remote control is designed to operate
the Cable set top boxes and the majority
Cable TV Remote Control of TV, VCR/DVD and AUDIO equipment on
the market.
Replacing Batteries
2
UR4-P360SI
Before you program or operate the
remote control, you must install two
new AA alkaline batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully,
and install the batteries as shown
in the illustration below.
STEP3 Replace the battery compartment cover.
Operations
4
Default State :
Device Default: Scientific Atlanta Explorer
and 8600X Cable boxes.
Volume Default: TV volume and mute
through the TV, with the option of
controlling volume and mute through the
Cable box or Audio. Refer to Section F for
programming the volume and mute
through your Cable box or Audio.
System On/Off button:
This button is designed to send out
Universal Remote Control, Inc.
power commands for two, three or all
www.universalremote.com
four devices with one button press.
OCE-0002B Rev 02(07/18/02)
Please refer to section E for details.
Button Functions
3
Programming the Remote Control
5
A. Programming For Your Devices.
The remote control can be programmed by pressing in a three digit code number
that corresponds to particular manufacturers and brands of Audio/Video
equipment. The three-digit code numbers are listed in the code table of the
instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUDIO).
STEP2 Press the [DEVICE] button (TV , VCR or AUD) to be programmed and the
[SELECT] button simultaneously for 3 seconds. The device LED will turn
on indicating the unit is ready to be programmed.
*Tip : The device LED will light on for 20 seconds. The next step must be entered
while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit
code number assigned to your brand from the code tables.
*Tip : The equipment will turn off when STEP3 Press the [CH+] or [CH-] button
the correct three-digit code one step at a time or keep it
number has been entered. You pressed. The remote will emit
can verify you have selected the a series of Power ON/OFF
correct code by pressing the commands. Release the [CH+]
[MUTE] button, the equipment or [CH-] button as soon as the
should turn on or turn off. equipment turns off.
*Note : If there is more than one STEP4 Press the same [DEVICE]
three-digit number listed for your button to store the code. The
brand, try one code number at a time Device LED will blink twice to
until your equipment turns off. confirm that the code has
been stored.
STEP4 Store the three-digit code
number by pressing the same
C. To Find the Three Digit
[DEVICE] button once again.
Code Number That was
The device LED will blink
Stored in the Device.
twice to confirm that the
code has been stored.
STEP1 Press the [DEVICE] button (TV,
*Note : Try all the functions on the VCR or AUD) you wish to
remote control. If any of the functions verify and the [SELECT] button
do not work as they should, repeat from simultaneously for 3 second.
Step 2 using the next three-digit code The device LED will turn on.
number from the same brand list. Make
*Tip : The device LED will light on for
sure that the VCR/VOD button is in the
20 seconds. The next step must
VCR position when using your VCR.
be entered while the LED is on.
STEP2 Press the [INFO] button.
B. Auto Search Method.
The device LED will blink number of
If the three-digit code numbers assigned times indicating the number of each
to your brand do not turn off your digit of the code number. Each digit is
equipment or the code tables do not list separated by a 1 second pause of the
your brand, you can use the Auto Search LED being turned off.
Method to find the correct three-digit
Example : One blink, three blinks and
code number for your equipment by the
eight blinks with an interval of 1
following steps:
second of LED being turned off,
STEP1 Turn on the equipment you indicates the code number 138.
wish to operate.
Note : Ten blinks is equal to the number 0.
STEP2 Press the [DEVICE] button (TV,
VCR or AUD) to be programmed
D. Programming a second TV
and the [SELECT] button
to VCR Mode.
simultaneously for 3 seconds.
STEP1 Press the [VCR] button to be
The device LED will turn on.
programmed and the [SELECT]
*Tip : The device LED will light on for
button simultaneously for 3
20 seconds. The next step must
seconds. The [VCR] device
be entered while the LED is on. LED will turn on.
*Tip : The device LED will light on for F. Program the Volume Controls.
20 seconds. The next step must
By following the steps below, you
be entered while the LED is on.
can program the volume controls
(Volume UP, Volume Down and
STEP2 Press the [TV] button to
MUTE) to your TV, VCR and Audio.
access the TV code table.
The default volume control settings on
STEP3 Point the remote control
the remote control is TV volume
toward the equipment and
control. If you wish you can control
enter the three-digit code
the volume via your cable box or audio
number assigned to your TV
equipment. Use the following steps to
brand from the code tables.
change the volume control settings:
*Tip : You can verify that you selected
STEP1 Press the [CBL] button and the
the correct code by pressing the
[SELECT] button simultaneously
[MUTE] button. The equipment
for 3 seconds. The [CBL]
should either turn on or turn off.
device LED will turn on.
STEP4 Store the three-digit code
*Tip : The device LED will light on for
number by pressing the [VCR]
20 seconds. The next step must
button once again. The [VCR]
be entered while the LED is on.
device LED will blink twice to
STEP2 Press the [ VOL + ] button.
confirm that the code has
been stored.
STEP3 Press the [ CBL ], [ AUD ]
(whichever applicable) button.
The [CBL] device LED will
E. Programming the
blink twice to confirm the
System On/Off Button.
programming.
This button is pre-programmed to turn on
all devices with one button press, however To return to original state:
you can also program to turn on one or If you wish to restore the TV volume
two devices by following these steps: control in CABLE mode, repeat the
above steps by pressing [ TV ] button
STEP1 Press the [CBL] button.
in STEP3 .
STEP2 Press the [SYSTEM ON/OFF]
button and the [SELECT] button
G. Programming For
simultaneously for 3 seconds.
Advanced Function.
The [CBL] device LED will turn
on for 20 seconds.
In the CABLE mode, the [
can be programmed to act as a
STEP3 Press the [DEVICE] button
macro or favorite channel button to
you wish to store in the
send out up to 10 commands with
[SYSTEM ON/OFF] button and
one button press.
repeat this until you stored all
the power commands into
STEP1 Press the [CBL] button to
the [SYSTEM ON/OFF] button.
select the CABLE mode.
STEP4 Press the [CH+] button to save
STEP2 Press the [ ] button and
*
the power commands you
[SELECT] button simultaneously
stored. The [CBL] device LED will for 3 seconds. The [CBL] device
blink twice to confirm the saving. LED will turn on for 20 seconds.
* ] button