Related Manuals for Lanzar MAXP 2760
Summary of Contents for Lanzar MAXP 2760
- Page 1 AMPLIFIERS: AMPLIFIERS: MAXP 2760/MAXP 2960/MAXP 4260 USER’S MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Contents and introdction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 1 Amplifier featuer descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _. -
Page 3: Amplifier Featuer Descriptions
AMPLIFIER FEATUER DESCRIPTIONS ~Z760fNU'XPZ960 Z CHANNELAMPUFIERS The X..oVER slide switch selects the intermal crossover functions: - The input signal is routed directiy to the UNE OUT RCA jacks. regardless of the X-OVER setting simplifying daisy chaining of amplifiers. • HP: Selects the built in HIGH PASS filter. variable from 40 Hz to 2KHz. •... -
Page 4: Maxp2760/Maxp2960 Channel Amplifier Applications
MAXP2760/MAXP2960 2 CHANNEL AMPLIFIER APPLICATIONS FULL RANGE STEREO This ;s the most basic application for the MAX PRO Series 2 channel amplifiers. 1. Interconnect cable checklist: Connect the UNE INPUTS to the Radio/CD with good quality RCA cables. Z. Crossover Switch: The X-OVER switch must be in the FlAT position. -
Page 5: Maxp4260 Channel Amplifier Applications
MAXP4260 4 CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYS Here show how to use the 4 channel amplifiers as straightforward discrete 4 channel full range units. Interconnect c.ble checldlst: - Connect the four inputs of the amplifier a Radio/CD with quality RCA cables, SWItch .enlng checklist: -ljZCH X'()VER: FULL... -
Page 6: Maxp4260 Channel Amplifier Applications
MAXP4260 4 CHANNEL AMPLIFIER APPLICATIONS 2 way active, or b ... mpllfted system with mono bass This application shows how easily a 2 active system can be implemented using a MAX PRO series 4 channel amplifier. Channels I and 2 will be used for highs, and channels 3 and 4 for mono bass. -
Page 7: Maxp4260 Channel Amplifier Applications
MAXP42604 CHANNEL AMPLIFIER APPLICATIONS Front/ear high pass, using a Z channel amplifier for mono sub bass The combination of a 2 and a 4 channel amplifier, utilizing their built in crossovers. makes it a snap to put together a full system with front and rear highs. -
Page 8: Setting Up Systems After Installation For Best Performance
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE General: At this point you are ready to get more specific on the settings for your amplifier. HIgh Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. -
Page 9: Max Pro Series Amplifier Specifications
Lanzar MAX PRO SERIES AMPLIFIER FEATURES MODEL Out Power Rating RMSat40hms MAX at 4 Ohms MAX at 4 Ohms Bridced RMSat 2 Ohms Miscellaneous Spec Soft Start Sound Frequency Response -3dB Dampinc Factor SIN Ratio(A-Weight) THD & Noise Channel Separation at I KHz Varible Input Level Control Input Impedance Power and Diagnostic LED... -
Page 10: Troubleshooting
TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. AMPLIFIER WILL NOT POWER UP. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the +terminal. - Page 11 ZDUUDQW\ OLPLWHG :::/$1=$5&20 UG 6WUHHW ‡ %URRNO\Q 1< ‡ ‡ )$; ...