Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Dealer QR Locator The QR code on the left will link you to available dealers for Land Pride products. Refer to Parts Manual QR Locator on this page for detailed instructions. Model SBR72 Seed Bed Roller 322-215M...
Page 4
Allow only enough slack in the chain to permit turning. Do not use safety chain for towing. Model SBR72 Seed Bed Roller 322-215M Table of Contents Transport Machinery Safely Comply with state and local laws. Maximum transport speed for implement is 20 mph.
Page 5
When removing and installing wheels, use wheel handling equipment adequate for the weight involved. Model SBR72 Seed Bed Roller 322-215M Avoid High Pressure Fluids Hazard Escaping fluid under pressure can penetrate the skin causing serious injury.
Read and follow their directions. Keep all safety labels clean and legible. Replace all damaged or missing labels. To order new labels go to your nearest Land Pride dealer or visit our dealer locator at landpride.com. Some new equipment installed during repair requires safety labels to be affixed to the replaced component as specified by Land Pride.
Introduction Introduction Land Pride welcomes you to the growing family of new product owners. This Seed Bed Roller has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance and safe operating practices will help you get years of satisfactory use from the machine.
3. For further assistance write to: Land Pride Service Department 1525 East North Street P.O. Box 5060 Salina, Ks. 67402-5060 E-mail address lpservicedept@landpride.com Model SBR72 Seed Bed Roller 322-215M Table of Contents 2/04/12...
6. Install 3/4"-10 x 3 1/2" GR5 hex head cap screw (#5B) and 3/4" hex flange lock nut (#8). Draw nut up snug. 7. Tighten 5/8" hex flange lock nuts (#7) to the correct torque. Three point Hitch Assembly Figure 1-1 Model SBR72 Seed Bed Roller 322-215M...
Pull Type Hitch Assembly With Drawbar 13" & Higher Figure 1-2 Model SBR72 Seed Bed Roller 322-215M Table of Contents c. Attach back of tongue with two 3/8"-16 x 1" GR5 cap screws (#8) and 3/8" flange lock nuts (#15).
1 1/4" spacer (#2) and lower hooks to hitch pins (#1). Tractor 3-Point Hitch Top Center Link Hole Alignment Position 25781 Seed Bed Roller Hook-Up Model SBR72 Seed Bed Roller 322-215M 23998 Figure 1-5 Lower Lift Arm Hole Alignment Positions Figure 1-6...
Seed Bed Roller. Tighten nut supplied with the ball to correct torque. 2" Ball with 3/4" shank (P/N 890-975C) can be purchased from Land Pride. 2. Back machine up to the Seed Bed Roller until the 2" ball is in alignment with ball socket in hitch (#2).
2. Rotate ball hitch about plate (#2) by hand. If ball hitch will not rotate, back nut (#3) off until it will rotate. 2/04/12 Table of Contents 25784 Scraper Adjustment Insert Socket Extension In This Opening Ball Hitch Swivel Adjustment Model SBR72 Seed Bed Roller 322-215M Figure 2-1 25785 Figure 2-2...
Refer to your tractor Operators Manual to determine whether or not to add ballast. Model SBR72 Seed Bed Roller 322-215M Table of Contents Make the following inspections if the Seed Bed Roller is attached to a drawbar: 1.
Field Set-Up. IMPORTANT: Beware of negative hitch weight when unhooking. Figure 3-1 Rotate Hitch 180 Over Roller Body To Change to Transport Set-Up IMPORTANT: Beware of positive hitch weight when unhooking. Figure 3-2 Model SBR72 Seed Bed Roller 322-215M Over...
Chock rear roller if needed especially if unit is not on level ground. over the roller body to 5. Repaint where paint is worn or scratched to prevent rust. Ask your dealer for Land Pride touch-up paint. Part No. 821-011C 821-002C...
Never pull onto hard surfaces or paved areas with the roller on the ground or excessive wear and damage may occur. The Land Pride Seed Bed Roller is a very user friendly attachment and with a little practice you should begin to achieve professional results in no time at all.
Always use genuine Land Pride replacement parts. Any Land Pride equipment that has been altered or modified without Land Pride’s specific recommendation, approval and authorization in writing excludes the warranty.
Accessories are available for mounting the spreader to a 2" receiver hitch on a utility vehicle or to a Land Pride Disc Harrow. A rear hitch can be attached to the Disc Harrow Spin Spreader mounting bracket. The Drag Harrow and Seed Bed Roller can then be hitched to the rear hitch.
This system is comprised of a Land Pride Disc Harrow, rear mounted Electric Spin Spreader with special hitch kit, trailing Drag Harrow, and trailing Pull-type Seed Bed Roller.
Indexing dual capability hitch on Pull-type configuration. Low maintenance indexing flip-over hitch on pull-type configuration. Notched and ribbed patterned gray iron roller. Model SBR72 Seed Bed Roller 322-215M Table of Contents SBR Series Benefits Matches customers operational and equipment needs.