Safety Instructions; Materials Required; Tools Required - Amana IC3 Installation And Operating Instructions Manual

Introduction
!
To avoid personal injury or property damage, observe
all safety instructions.
Read entire manual before installing kit. All necessary
tools and materials must be available prior to installation.
Verify all listed parts are included in kit. If parts are
missing, contact source from whom kit was purchased.
• Mechanical experience is required to install kit.
Installation can take from 3 to 6 hours.
• If unable to solve a problem during installation, contact
®
an authorized Amana
Service Center or independent authorized technician by
calling 1-800-628-5782 inside U.S.A. and 1-319-622-
5511 outside U.S.A. Service is at owner's expense.

Safety Instructions

!
WARNING
To avoid electrical shock which can cause severe
personal injury or death, unplug power cord or open
household circuit breaker to refrigerator before
installing kit. After installing kit, reconnect power.
!
To avoid property damage, observe the following:
• Confirm water pressure to water valve is at least 20
pounds per square inch.
• Start nuts by hand to avoid cross threading. Finish
tightening nuts using a wrench. Do not overtighten.
• Check carefully for water leaks prior to returning
refrigerator to normal location and 24 hours after
connection.

Materials Required

Important
• Before connecting ice maker, contact a plumber to
connect copper tubing to household plumbing in
compliance with local codes and ordinances.
• Amana Appliances recommends using a saddle valve.
Do not use self-piercing valve. Amana Refrigeration,
Inc. is not responsible for property damage due to
improper installation or water connection.
1
/ " (6 mm) flexible copper tubing*.
4
*Length of copper tubing must reach from water supply
connection plus an additional 8' (2
behind refrigerator. Tubing should be soft instead of rigid
and ends should be free of burrs.
CAUTION
technician. Locate a Factory
CAUTION
1 / m) for service loop
2

Tools Required

• 3 / " electric drill (ground fault protected)
8
3
• / " drill bit
8
1
• / " open-end wrenches (2)
2
• Flat blade screwdriver
• Small knife
• Bucket
• Gloves
Parts
Use listed part numbers only when ordering replacement
parts. Part numbers are not used in installation
instructions.
Item Description
1 Ice Maker
2 Ice maker cover
N/S Ice maker cover decorative trim
(TM,TJ, TR, TX models)
N/S Ice maker cover decorative insert
(TC models)
N/S Ice maker cover decorative insert
(TL models)
N/S Ice maker cover decorative insert
(Blue)
N/S Ice maker cover decorative insert
(TZ models)
N/S Warning label
N/S Diagnostic label
N/S Ice maker arm
3 Stainless steel clip
4 Water fill tube extension
5 Ice maker wiring harness
6 Thermal fuse clip
7 Button plug
9 Ice storage bucket
N/S Ice storage bucket decorative
insert (TC models)
N/S Installation and operating
instructions
N/S Ice storage bucket decorative
insert (TX models)
N/S Ice storage bucket decorative
insert (TL models)
N/S Ice storage bucket decorative
insert (Blue)
N/S Ice storage bucket decorative
insert (TZ models)
10 Water valve
N/S Water valve clip
11 Water valve mounting bracket
3
12 / " cutting screw
8
13 Water valve coupling assembly
14 Nylon nut and sleeve
15 ¼" plastic tubing
16 Anti-kink spring
17 Stainless steel insert
18 Hose clamp
19 "P" clamp
20 Plastic clip
2
1
• / " hex nut driver
4
• Adjustable wrench
• Slip joint pliers
• Masking tape
• Towel
Part Number Quantity
D7824703 1
B5724506 1
C8963607 1
C8963615 1
C8963609 1
C8963610 1
C8963614 1
A3036901 1
10834701 1
10884401 1
B5720301 1
A3127401 1
D7813004 1
10319801 1
M0311301 2
D7621116 2
C8987005 1
10527026 1
C8987002 1
C8987003 1
C8987004 1
C8987006 1
D7712603 1
A3223101 1
D7701602 1
M0251015 3
10244903 1
M0753001 1
B5705308 1
A1055101 1
A3223101 1
M0114003 1
M0108001 11
M0104101 1