Download
Share
Print this page
Milwaukee 7150-21 Operator's Manual
  1. Manuals
  2. Brands
  3. Milwaukee Manuals
  4. Nail Gun
  5. 7150-21
  6. Operator's manual

Milwaukee 7150-21 Operator's Manual

18 ga. brad nailer
Hide thumbs Also See for 7150-21:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: Operator's Manual
Enlarged version
Cat. No.
No de cat.
7150-21
18 ga. BRAD NAILER
18 ga. MARTEAU CLOUEUR
CLAVADORA DE CLAVITOS, calibre 18
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LES RISQUES DE BLESSURES, L'UTILISATEUR DOIT LIRE
LE MANUEL DE L'OPÉRATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR

Advertisement

loading

Related Manuals for Milwaukee 7150-21

Summary of Contents for Milwaukee 7150-21

  • Page 1 OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. No de cat. 7150-21 18 ga. BRAD NAILER 18 ga. MARTEAU CLOUEUR CLAVADORA DE CLAVITOS, calibre 18 TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL. AFIN DE RÉDUIRE LES RISQUES DE BLESSURES, L’UTILISATEUR DOIT LIRE LE MANUEL DE L’OPÉRATEUR.
  • Page 2 12. The operator and other people in the contact or leaving work area. Verify the GENERAL SAFETY INSTRUCTIONS work area must wear eye protection tool is empty and there is no residual pres- in accordance with ANSI Z87.1. Eye sure in the tool prior to performing these protection does not fi...

  • Page 3: Specifications

    Hold the tool fi rmly label is damaged or missing, contact and be prepared for the recoil. Specifi cations MILWAUKEE for a free replacement. Do not remove, tamper with, or otherwise cause the tool operating Cat. Operating...

  • Page 4: Functional Description

    ASSEMBLY FUNCTIONAL DESCRIPTION WARNING Removing and Installing the Belt Hook Fig. 1 Disconnect the air supply from the Front of tool tool and remove fastener strips Belt hook before changing or removing acces- Screw (2) sories. Only use accessories spe- End cap cifi...
  • Page 5 Connecting the Air Supply Installing Fastener Strips Place the points of a strip of brad nails Removing Fastener Strips onto the bottom groove of the maga- DANGER WARNING zine. WARNING Fig. 3 Do not use oxygen, combustible gas- Always point the tool away from To avoid serious injury, disconnect Point of es or bottled gases as a power source...

  • Page 6: Operation

    Clearing a Jammed Fastener OPERATION Most jams are caused by a fastener or part of a fastener wedging between the driver blade and the nail guide. Fastener strips with an WARNING WARNING incorrect collation angle or the wrong fas- tener type may cause continuous jamming. The operator and other people in the To reduce the risk of injury to your- To clear the jam:...
  • Page 7 Reload fastener strip according to "In- trigger for 5 seconds. The tool must not by grasping the discharge area of the contact a MILWAUKEE service facil- stalling Fastener Strips". operate. ity immediately. tool. Doing so could result in serious Continue to pull and hold the trigger and injury.

  • Page 8: Maintenance

    FIVE YEAR TOOL MAINTENANCE ACCESSORIES LIMITED WARRANTY WARNING Every MILWAUKEE tool is tested before leaving WARNING Cold Weather Operation the factory and is warranted to be free from defects For cold weather operation, near and below in material and workmanship. MILWAUKEE will To reduce the risk of injury, use only repair or replace (at MILWAUKEE’s discretion),...