Electric drill bit
and chisel sharpener (15 pages)
Summary of Contents for Chicago Electric 94782
Page 1
ElEctric powEr nibblEr Model 94782 AssEMbly And opErAtion instructions Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com to prEVEnt sErious injury, rEAd And undErstAnd All wArnings And instructions bEforE usE.
Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. for technical questions, please call 1-800-444-3353. SKU 94782 Page 2...
Avoid accidental starting. be sure the power switch is off before plugging in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. for technical questions, please call 1-800-444-3353. SKU 94782 Page 3...
Many accidents are caused by poorly maintained tools. use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. for technical questions, please call 1-800-444-3353. SKU 94782 Page 4...
Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks and cement or other masonry products for technical questions, please call 1-800-444-3353. SKU 94782 Page 5...
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (see 3-prong plug and outlet.) for technical questions, please call 1-800-444-3353. SKU 94782 Page 6...
Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electri- cian before using it. for technical questions, please call 1-800-444-3353. SKU 94782 Page 7...
Page 8
* based on limiting the line voltage drop to five volts at 150% of the rated amperes. syMbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes n 0 xxxx/min. No Load Revolutions per Minute (RPM) for technical questions, please call 1-800-444-3353. SKU 94782 Page 8...
Down-Blade Block (8) and Plunger Guide (9). Continue to slide the Cutting Knife up into the shaft in the Piston (2). Thread back on the Nut (7) using the Collar Wrench (63). for technical questions, please call 1-800-444-3353. SKU 94782 Page 9...
As necessary, wipe off the Nibbler with a damp cloth. You may use a mild detergent or non-flammable solvent. Once clean, lubricate all moving parts with a light oil. When storing, keep the Nibbler in the case, out of the reach of children. for technical questions, please call 1-800-444-3353. SKU 94782 Page 10...
Nibbler will not cut Cutting Knife needs replacing. Follow directions for Replacing smoothly; motor runs Cutting Knife on page 9. Material too thick. slowly during cuts. Cut only proper thickness and materials. for technical questions, please call 1-800-444-3353. SKU 94782 Page 11...
M5-50 Inner Hex Bolt Back Motor Cover Elastic Washer Plug Cable Flat Washer Cable Sheath Positioned Sleeve Screw Rod Motor End Casing Flat Washer Self-Tapping Screw Collar Wrench Plastic Sealing Washer Hex Wrench for technical questions, please call 1-800-444-3353. SKU 94782 Page 12...
Page 13
And AssEMbly diAgrAM Parts and Assembly Diagram continued on next page Collar Wrench (63) and Hex Wrench (64) not shown for technical questions, please call 1-800-444-3353. SKU 94782 Page 13...
Page 14
And AssEMbly diAgrAM for technical questions, please call 1-800-444-3353. SKU 94782 Page 14...
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. for technical questions, please call 1-800-444-3353. SKU 94782 Page 15...