Korg CX-3 Combo Organ Owner's Manual page 29

Rtry FAST Ctrl (Rotary FAST Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY
[FAST] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Rtry FAST Pedal (Rotary FAST Pedal Mode)
Select the on/off operation of the pedal switch etc.
connected to the rear panel ASSIGNABLE PEDAL/SW 1
or 2 jack. The pedal switch will have the same function as
pressing the front panel ROTARY [FAST] key.
Alter: Once you press the pedal switch, the rotary speed
will gradually increase until it reaches the speed specified
by the Group 6 "Rotor Fast Speed" parameter. When you
press the pedal switch once again, the rotary speed will
gradually decrease until it reaches the speed specified by
the Group 6 "Rotor Slow Speed" parameter.
Momnt: The rotary speed will gradually increase as long
as you continue pressing the pedal switch, until it reaches
the speed specified by the Group 6 "Rotor Fast Speed"
parameter. When you release the pedal switch, the rotary
speed will gradually decrease until it reaches the speed
specified by the Group 6 "Rotor Slow Speed" parameter.
Rtry STOP Ctrl (Rotary STOP Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
Pedal 1: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will turn the ROTARY
[STOP] key on/off.
Pedal 2: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off: No function.
Rtry STOP Pedal (Rotary STOP Pedal Mode)
Selects the on/off operation of a pedal switch etc. con-
nected to the rear panel ASSIGNABLE PEDAL/SW 1 and
2 jacks. The pedal switch etc. will have the same function
as pressing the [STOP] key in the front panel ROTARY
section.
Alter: The [STOP] key LED will alternate between lit and
dark each time you press the pedal switch etc.
Momnt: The [STOP] key LED will be lit as long as you
continue holding down the pedal switch etc.
Amp Gain Ctrl (Amp Gain Controller)
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
Pedal 1: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 1 jack will control the
Group 4 "Amp Gain" parameter of Normal Edit mode
and EX Edit mode.
Pedal 2: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 2 jack will perform the
above operation.
Off: No function.
* (Pdl 1), (Pdl 2): These indicate that Pedal 1 or Pedal 2 are selected for the Global mode Group 1 "Prog Up Ctrl" or "Prog Down Ctrl" parameters. With these settings, the settings of
Global mode are used, and the settings you made here will be ignored. However if you select another value in Global mode, the display here will change from (Pdl 1) to Pedal 1 or
from (Pdl 2) to Pedal 2, and you will be able to operate the corresponding function from the pedal switch.
Amp Gain Ctrl Min (Amp Gain Control Minimum)
Specify the minimum setting of the Normal Edit mode
and EX Edit mode Group 4 "Amp Gain" parameter.
This will be the gain when the expression pedal etc.
specified by the "Amp Gain Ctrl" parameter is in the
minimum position.
Amp Gain Ctrl Max (Amp Gain Control Maximum)
Specify the maximum setting of the Normal Edit mode
[Alter, Momnt]
and EX Edit mode Group 4 "Amp Gain" parameter.
This will be the gain when the expression pedal etc.
specified by the "Amp Gain Ctrl" parameter is in the
maximum position.
Rev Mix Ctrl (Reverb Mix Controller)
Pedal 1: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 1 jack will control the
Group 5 "Reverb Mix Level" parameter of Normal Edit
mode and EX Edit mode.
Pedal 2: An expression pedal etc. connected to the rear
panel ASSIGNABLE PEDAL/SW 2 jack will perform the
above operation.
Off: No function.
Rev Mix Ctrl Min (Reverb Mix Control Minimum)
Specify the minimum setting of the Normal Edit mode
and EX Edit mode Group 5 "Reverb Mix" parameter.
This will be the reverb mix level when the expression
pedal etc. specified by the "Reverb Mix Ctrl" parameter is
in the minimum position.
Rev Mix Ctrl Max (Reverb Mix Control Maximum)
Specify the maximum setting of the Normal Edit mode
and EX Edit mode Group 5 "Reverb Mix" parameter.
This will be the reverb mix level when the expression
pedal etc. specified by the "Reverb Mix Ctrl" parameter is
[Alter, Momnt]
in the maximum position.
Mod Wheel (Modulation Wheel)
Selects the parameter that will be controlled when MIDI
Modulation Wheel control change messages are received.
If you set this to other than No Assign, Rtry FAST, or
Wheel Brake, the result of receiving the message will
depend on the setting of the "Mod Wheel Range" param-
eter (following).
No Assign: Incoming MIDI Modulation Wheel control
change messages will not control anything.
Click Level: The "On Click Level" and "Off Click Level"
parameters (Group 1) will be controlled.
Perc Level (Percussion Level): The "Perc Nrml Level"
parameter (Group 3) will be controlled.
Perc Decay (Percussion Decay): The "Perc Fast Level"
parameter (Group 3) will be controlled.
Rtry FAST (Rotary Fast/Slow): The [FAST] key of the
front panel ROTARY section will be controlled. When
MIDI Modulation Wheel control change messages are
received, the speed will be fast for a value of 127 (7Fh),
and slow for a value of 0 (00h).
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
[No Assign...ExLm Level]
Parameters
[0...99]
[0...99]
[0...99]
[0...99]
29