Korg CX-3 Combo Organ Owner's Manual page 27

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 4: Amp
Amp Type
here you can select the amp type.
Type 1: This is a conventional organ power amp. It
produces a mild and fat sound.
Type 2: Compared to Type 1, this emphasizes the high
range, and produces a more uncolored sound.
Pre Amp: Use a pre amp. This is the sound of the organ's
line-out.
When Type 1 or Type 2 are selected: When the front
panel ROTARY [ON] key is used to turn on the
rotary speaker, the effect of the rotary speaker will be
simulated. When this is turned off, a conventional
speaker will be simulated.
When Pre Amp is selected: The power amp and
rotary speaker will not be used, and the sound will
be as if it were taken from the preamp line-out of the
organ itself.
Spkr Simulator (Speaker Simulator)
When the "Amp Type" parameter is set to Type 1 or Type
2, this turns the amp simulator function on or off.
Amp Gain
Adjusts the gain (amplification) when the "Amp Type"
parameter is set to Type 1 or Type 2.
With high settings of this value, the sound will distort
more severely when the expression/overdrive is raised.
This setting will not apply if the "Amp Type"
parameter is set to Pre Amp.
Tone Treble
Adjusts the high frequency level of the amp selected by
the "Amp Type" parameter.
Tone Middle
Adjusts the mid-frequency level of the amp selected by
the "Amp Type" parameter.
Tone Bass
Adjusts the low frequency level of the amp selected by
the "Amp Type" parameter.
Amp Type: Amp 1 or Amp 2
Amp 1
Pre Amp or
Amp 2
Group 4: Amp Gain
Tone Trebel
Tone Middle
Tone Bass
Amp Type: Pre Amp
Pre Amp
Group 4: Tone Trebel
Tone Middle
Tone Bass
[Type 1, Type 2, Pre Amp]
[On, Off]
[0...99]
[-10...+10]
[-10...+10]
[-10...+10]
Speaker Reverb Rotary
Group 4: Spkr Simulator
Group 5: Rev Routing
Reverb
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 5: Reverb
Reverb Type
Selects the type of reverb.
Reverb Time
Specifies the reverb time.
The range in which the reverb time can be adjusted
will depend on your selection for the "Reverb Type"
parameter.
Reverb Mix Level
Specifies the amount of reverb signal that is mixed with
the original sound.
Rev Routing (Reverb Routing)
Selects whether the reverb will be applied before the
rotary speaker or after it.
Rot->Rev: Reverb will be applied after the rotary speaker.
Rev->Rot: Reverb will be applied before the rotary
speaker.
This setting will not be used if the "Amp Type"
parameter is set to Pre Amp.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 6: Rotary Effect
These settings will not be used if the "Amp Type"
parameter is set to Pre Amp.
Horn: 0 Rotor: 100 (Rotary Horn/Rotor Balance)
Adjuststhe volume balance between the horn and rotor of
the rotary speaker.
Horn Slow Speed
Specifies the rotational speed of the horn during slow
rotation.
Horn Fast Speed
Specifies the rotational speed of the horn during fast
rotation.
Rotor Slow Speed
Specifies the rotational speed of the rotor during slow
rotation.
Rotor Fast Speed
Specifies the rotational speed of the rotor during fast
rotation.
Horn Up Transit (Horn Up Transition)
Specifies the time over which the horn will change from
slow to fast rotation.
Horn Down Transit (Horn Down Transition)
Specifies the time over which the horn will change from
fast to slow rotation.
Horn Stop Transit (Horn Stop Transition)
Specifies the time it will take for the horn to actually
come to rest after rotation is switched off.
Horn Strt Transit (Horn Start Transition)
Specifies the time it will take for the horn to reach the
specified speed after rotation is switched on.
Parameters
[Room, Hall, Plate, Dark]
[00.25...16.00 (Sec)]
[0...99]
[Rot->Rev, Rev->Rot]
[0:100...100:0]
[0...99]
[0...99]
[0...99]
[0...99]
[0...99]
[0...99]
[0...99]
[0...99]
27