Hilti TE 700-AVR Operating Instructions Manual
Breaker
Hide thumbs
Also See for TE 700-AVR:
- Operating instructions manual (249 pages) ,
- User manual (184 pages) ,
- Manual (156 pages)
Table of Contents
Advertisement
Printed: 08.07.2013 | Doc-Nr: PUB / 5071154 / 000 / 02
TE 700-AVR
Bedienungsanleitung
Operating instructions
Mode d'emploi
Istruzioni d'uso
Manual de instrucciones
Manual de instruções
Gebruiksaanwijzing
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Οδηγιες χρησεως
Lietošanas pamācība
Instrukcija
Kasutusjuhend
de
en
fr
it
es
pt
nl
da
sv
no
fi
el
lv
lt
et
Advertisement
Table of Contents
Related Manuals for Hilti TE 700-AVR
Summary of Contents for Hilti TE 700-AVR
- Page 1 TE 700-AVR Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Οδηγιες χρησεως Lietošanas pamācība Instrukcija Kasutusjuhend Printed: 08.07.2013 | Doc-Nr: PUB / 5071154 / 000 / 02...
- Page 2 Printed: 08.07.2013 | Doc-Nr: PUB / 5071154 / 000 / 02...
- Page 3 Printed: 08.07.2013 | Doc-Nr: PUB / 5071154 / 000 / 02...
-
Page 4: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS TE 700‑AVR breaker 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages. -
Page 5: Description
Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Wear eye Wear a hard... - Page 6 To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. Modification of the power tool or tampering with its parts is not permissible.
-
Page 7: Accessories, Consumables
TPS‑K key Dust removal module TE DRS‑B Use the Hilti chisels or other tools listed below. With these you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. TE‑Y chuck /... -
Page 8: Technical Data
TE‑Y chuck / Width in Length in tool descrip- Width (mm) Length (mm) inches inches tion Flexible chisel TE‑Y 25¹⁄₂ BSPM 800 Scraper / flexible chisel TE‑YP SPMK 5/28 TE‑YP 4³⁄₄ SPMK 12/50 Hollow chisel TE‑Y HM 2.8/28 Channel chisel TE‑Y ⁷⁄₈... -
Page 9: Safety Instructions
Noise and vibration information (measured in accordance with EN 60745‑1): Typical A-weighted sound power level, TE 700-AVR 97 dB (A) Typical A-weighted emission sound pressure level, TE... - Page 10 d) Do not abuse the cord. Never use the cord for preventive safety measures reduce the risk of carrying, pulling or unplugging the power tool. starting the power tool accidentally. Keep cord away from heat, oil, sharp edges or d) Store idle power tools out of the reach of chil- moving parts.
- Page 11 This will prevent accidental of dust collection, use a suitable vacuum cleaner restarting when the electric power returns. of the type recommended by Hilti for wood dust and/or mineral dust together with this tool. Ensure 5.3.3 Work area that the workplace is well ventilated.
-
Page 12: Before Use
Clean it and grease it if neces- switch when the supply cord is plugged back in after sary. unplugging, the power tool must be brought to Hilti Check that the sealing lip of the dust shield is clean Service immediately. -
Page 13: Care And Maintenance
CAUTION 7.2.2 Chiseling Working on the material may cause it to splinter. Use 7.2.2.1 Working at low temperatures eye protection, protective gloves, safety shoes and NOTE a lightweight breathing mask. Flying fragments may The power tool must reach a minimum operating tem- cause injury to the eyes or other parts of the body. -
Page 14: Troubleshooting
Clean the sealing lip by wiping it carefully and then grease it again lightly with Hilti grease. Check all external parts of the power tool for damage It is essential that the dust shield is replaced if the sealing at regular intervals and check that all controls operate lip is found to be damaged. -
Page 15: Disposal
NOTE If the fault can not be eliminated by the measures listed above, have the power tool checked by Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. -
Page 16: Manufacturer's Warranty - Tools
11 Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects in Additional claims are excluded, unless stringent na- material and workmanship. This warranty is valid so long tional rules prohibit such exclusion. In particular, Hilti... - Page 17 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3983 | 0613 | 00-Pos. 1 | 1 Printed in Germany © 2013 Right of technical and programme changes reserved S. E. & O 428075 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5071154 / 000 / 02...