HP R100-Series Quick Start Manual page 2

HP R100-Series Wireless VPN Routers Quickstart
Package contents
The HP R110 or HP R120 router, two mounting screws with wall anchors, four
rubber feet, AC/DC power adapter, and documentation.
Ports
• Four LAN Ethernet ports: Auto-sensing 10/100/1000 BaseT Ethernet ports
with RJ-45 connectors.
• One WAN Ethernet port: Auto-sensing 10/100/1000 BaseT Ethernet port
with RJ-45 connector.
• USB port: A standard USB 2.0 port that can be connected to an external
USB storage device. For details, see the USB port description in the HP
R100-Series Wireless VPN Routers Configuration/Administration Guide.
Radio and antennas
The HP R110 provides a single dual-band radio with three antennas supporting
3x3 MIMO three-spatial-stream 802.11n. The HP R110 supports 802.11b/g/n
operation modes at 2.4 GHz or 802.11a/n operation modes at 5 GHz. The
HP R110 does not support concurrent operation at 2.4 GHz and 5 GHz.
The HP R120 provides dual radios (2.4 GHz and 5 GHz) with three antennas per
radio supporting 3x3 MIMO three-spatial-stream 802.11n and 802.11ac. The
HP R120 supports 802.11b/g/n operation modes at 2.4 GHz and 802.11a/n/ac
operation modes at 5 GHz. The HP R120 supports concurrent operation at
2.4 GHz and 5 GHz.
Wi-Fi On/Off button
Press the button for more than three seconds and then release it to turn the
wireless function of the router on or off.
WPS button
Press the button for more than three seconds to enable Wi-Fi Protected Setup
(WPS) and allow a wireless client device to securely join the network. Within
two minutes, initiate the WPS procedure on the wireless client device. See the
wireless client documentation for information on how to connect to access
points using WPS.
Reset button
The Reset button is accessible through a hole on the front panel of the
HP R110/R120, labeled as 6 on page 1. To reset the HP R110/R120 to factory
defaults, insert a paper clip into the Reset button hole and hold the button for
more than three seconds, then release.
2
Status LEDs
LED State
Off
Power
White
Amber
Alert
Flashing
amber
Off
USB
Blue
Off
Blue
WPS
Flashing
blue
Off
WAN
Blue
Off
LAN 1-4
Blue
Off
2.4 GHz
Blue
Description
The HP R110/R120 has no power.
The HP R110/R120 is fully operational.
The HP R110/R120 has a hardware failure or the
software has failed to load. Reset or power cycle
the HP R110/R120. If this condition persists,
contact HP customer support.
Indicates one of the following conditions:
• The HP R110/R120 is starting up following
a hard or soft reset.
• The HP R110/R120 is upgrading firmware.
• The HP R110/R120 software is being reset
to factory defaults.
• A hacker attack is detected. The Alert LED
remains flashing until the hacker attack
ends.
• The Alert LED remains flashing for 30
seconds when a USB overcurrent condition
is detected.
Either an unsupported or defective USB device is
attached.
A USB device is attached.
WPS is not active.
On for 20 seconds when WPS is successful.
WPS is active and waiting for a wireless client
device to join the network.
The WAN port is not connected.
The WAN port has a valid link. Flashing indicates
network activity.
The LAN port is not connected.
The LAN port has a valid link. Flashing indicates
network activity.
The 2.4 GHz radio is disabled.
The 2.4 GHz radio is enabled. Flashing indicates
wireless network activity.