Tail Boom Assembly - THUNDER TIGER Raptor 30 V2 User Manual

14 Tail Boom Assembly

Assembly Tip: Slide the 3 rod guides onto the boom and space them out evenly as shown. Then slide the tail linkage
rod into the rod guides. Next, insert the tail rotor drive belt into the boom so that it comes out of both ends. Place
drive belt over tail drive pulley and complete balance of tail boom assembly. Remember to connect the tail linkage
rod to the tail control lever.
(1) HMC3-20B Socket Screw(M3x20).. 4
(2) HMC3-25B Socket Screw(M3x25).. 2
(3) HSE3-12B Self Tapping Screw(M3x12).. 4
(4) HMM3Z Lock Nut(M3).................... 6
(5) HMV1150X Bearing (d5xD11xW5)..1
(6) BK0046 Tail Unit Housing (L)..........1
(7) BK0071 Vertical Fin........................ 1
(8) BK0069 Stabilizer Fin..................... 1
(9) BK0070 Stabilizer Fin Bracket........ 1
(10) BK0540 Tail Support Rod..............2
(11) BK0060 Tail Boom........................ 1
(12) BK0091 Rod Guide........................3
(13) BK0089 Tail Rotor Drive Belt... .....1
(14) BK0100-2 Tail Linkage Rod.......... 1
(15) BK0086 Ball Link.......................... 1
(16) BV0052 Tail Idle Pulley................. 1
(17) Tail Unit
(18) HMJ2-8N Seif Tapping Screw(M2x8)..4
(19) BK0447 Tail Support Rod End........... 4
15 Main Frame Assembly-Part6
(5) BK0068
(1) HMC3-14B
Insert the four 3x20 socket screws into the tail base of the Main Frame
and secure with lock nuts. Do not tighten at this point.
Hold the tail boom in one hand and hook your index finger on your free
hand through the exposed loop of the tail rotor drive belt. Hold it so the
belt is vertical and parallel to the tail drive pulley.
Boom Drive belt
Important: Next, rotate the belt 90-degree counter clockwise.
90-degree
Pull the belt through the tail base, keeping the belt correctly aligned.
Push the tail boom into the tail base all the way to the end. Place the
drive belt over the tail drive spur gear. Then, gently pull back on the tail
boom until the tension on the belt allows no more than 5mm(3/16") of
free play in the belt. Tighten the locknuts and proceed with the rest of
the assembly.
(2) HMC3-25B
(15) BK0086
(8) BK0069
(14) BK0100-2
(11) BK0060
(12) BK0091
(13) BK0089
(5) BK0068
(4) HMM3Z
(4) HMM3Z
(3) HSE3-12B
13
(17) Tail Unit
(1) HMC3-20B
(12) BK0091
(10) BK0540
(18) HMJ2-8N
(19) BK0447
(1) HMC3-14B Socket Screw(M3x14)......2
(2) HMC3-20B Socket Screw(M3x20)......4
(3) HSE3-12B Self Tapping Screw(M3x12).... 2
(4) HMM3Z Lock Nut(M3)........................ 6
(5) BK0068 Tail Rotor Blade.................... 2
(6)Tail Assembly
(6)Tail Ass'y
(4) HMM3Z
(16) BV0052
(5) HMV1150X
(6) BK0046
(3) HSE3-12B
(9) BK0070
(4) HMM3Z
(7) BK0071
(2) HMC3-20B