Related Manuals for Haier HLP23E
Summary of Contents for Haier HLP23E
- Page 1 Automatic Washing Machine User's manual This manual is for HLP23E Please read this manual carefully before using. Retain it for future reference.
-
Page 2: Table Of Contents
Contents Names of the parts..........1 Safety precautions ..........2 Installation and adjustment .......4 Install the water inlet hose.........6 Preparation before washing ......7 Put in the laundries ...........8 Put in the detergent ..........9 Use the operation buttons ......10 Close the top lid ..........14 Finish washing ..........15 Disposal after washing ........15 Trouble shooting Answer to questions..16... -
Page 3: Names Of The Parts
Before Using Before Using Names of the parts Water valve Water absorption cushion Top lid B Top lid A Lint filter(Installed by user) Detergent box Control panel Filter cover Cabinet handle Inner tub Pulsator Power line Control panel film Cabinet Back cover Adjustable foot Adjustable foot (4) -
Page 4: Safety Precautions
Before Using Before Using Safety precautions Please insert the power cord into special rece- The power cord plug should be convenient ptacle with rated voltage.The earthing to be pluged in or pluged out with hand terminal of the receptacle must be earthed while the washing machine runs normally. - Page 5 Before Using Before Using Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children.Do not let the children climb the washing machine.
-
Page 6: Installation And Adjustment
Before Using Before Using Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter Install the bottom plate After you open the package, 1.Press downward to assmble. -
Page 7: Usage Of The Drain Hose
Before Using Before Using Usage of the drain hose The drainage shall be smooth with the drain hose. 1.put the drain hose up to suitable position. Do not put it on ground 2.Do not step on or press the drain hose. Notes: the highest point of drain pipe should be higher than the water level of washing tub for avoiding to siphon phenomenon during drain. -
Page 8: Install The Water Inlet Hose
Before using Before using Install the water inlet hose Installing Quick Sink Adapter When installing the quick sink faucet adapter to the faucet follow the steps below 1.First remove the aerator from your faucet nozzle and determine thesize/tipe of the faucet 2.Once you determine the size/tipe of the faucet Outside Threaded End or inside... -
Page 9: Preparation Before Washing
Using process Using process 1 Preparation before washing Preparation before washing 1. Connect the water inlet hose. 2. Confirm that the washing machine is earthed reliably. Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. -
Page 10: Put In The Laundries
Using process Using process 2 Put in the laundries The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. One time washing quantity shall be lower than the rated capacity. -
Page 11: Put In The Detergent
Using process Using process 3 Put in the detergent Inlet for concentrated washing powder and detergent How to use the washing powder Direct dissolved in the machine 1.Fill water to "Low" water level. 2.Add the power. Run for 30 seconds to dissolve it completely. -
Page 12: Use The Operation Buttons
Using process Using process 4 Use the operation buttons Description of the function of the buttons SURPLUS(MIN) To indicate -- during sensing. To indicate remaining min. During program running. To indicate remaining reserved time (hrs) during reservation period. To indicate fault symbols for abnormal conditions (see page 15) Page 15 PROGRAM STATUS... - Page 13 Using process Using process "POWER ON/OFF"button Press "Power On/Off" button to connect power supply. After power is connected, pressing this button will cut off the supply. "START/PAUSE"button After the power is switched on, press it to start the machine During working, push it to pause working. During pause, push this button to restart and continue operation.
- Page 14 Using process Using process Operating procedure and explanations for the buttons PROGRAM STATUS PROCEDURE STATUS SURPLUS(MIN) HIGH HLP23E STANDARD SOAK MEDIUM HEAVY WASH GENTLE RINSE RINSE VERY LOW QUICK WASH SPIN SPIN WASH WASH POWER POWER START START ON/OFF ON/OFF...
- Page 15 Using process Using process Attention Even there's no water in the tub, the spinning will start after a certain period. laundries Do not use soak process for woolen Wash the laundries that are prone to lose colors separately from other laundries. The pulsator will not rotate unless the water is filled to selected water level.
-
Page 16: Water Level
Using process Using process Total time: including the normal water inlet time, drain time, excluding the power off time. The total washing time may be influenced by the water inlet pressure and water level. Spin time: the time from intermittent running to finishing. The Jeans program could combine the process of soak during which the washing machine firstly soak for about 25~45 min after water filling and then begins to wash. -
Page 17: Finish Washing
Using process Using process 6 Finish washing The washing machine cuts off the power supply automatically when wash cycle ends. After Finishing wash alarm automatically Disposal after washing After using, please clean the lint and foreign materials of the lint filter etc. in time. Otherwise it may influence your using the machine. -
Page 18: Trouble Shooting Answer To Question
Trouble shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department . Do not repair it by yourself. -
Page 19: Packing List
Common phenomena Phenomena Explanation The spinning is intermittent when it starts. Balance the laundries to avoid slanting. Push the" PROGRAM RESERVATION " button to The program is setting the drain time. Some time is select "Spin", but it doesn't work. needed before it starts spinning. -
Page 20: Specifications
Specification Specification Model HLP23E Water level/Water quantity (about) Lowest/20L Low/30L Mid/37L High/48L 0.03MPa-1.0MPa Water inlet pressure Dimensions mm L 500 W 500 H 882... -
Page 21: Warranty
1-514-223-9023 Haier 4742 Cote Des Neiges Montreal, QC H3V 1G2...