Install The Decorative Door Panels (Nonmetal Door Models) - Norcold N62X Installation Manual

- For N82X, N82XXX, N84X, N84XXX, N84XIM, and
N84XIMXX models, make sure the distance [25]
from the bottom of the enclosure to the top of the
rough opening for the upper exhaust vent is at least
62 inches.
- Align the upper exhaust vent [24] horizontally above
the lower intake vent [9] of the refrigerator.
- To prevent stagnant hot air in the area above the
refrigerator, install an aluminum or galvanized steel
sheet baffle [13] between the top of the refrigerator
and the top of the upper exhaust vent.
- Make sure there is less than 1/4 inch clearance
between the baffle and the top of the
refrigerator and that the baffle overlaps the
refrigerator 1 inch or less.
- Make sure that the baffle is against the wall of
the vehicle at the top of the upper exhaust vent
and 1/4 inch or less from the top of the opening
for the upper exhaust vent [15].
- Make sure the baffle is the full width of the
inside of the enclosure
- When using an upper side-wall exhaust vent:
- If the depth of the enclosure is 24 inches or more and
is less than 26 inches [27], install a bent aluminum
or galvanized steel sheet baffle [26] to the rear of the
enclosure (See Art01592).
- Make sure that the bend of the baffle is the full width
of the inside of the enclosure.
- Make sure that the bend of the baffle is flush with
the bottom edge of the upper intake vent door
frame.
- Make sure that the top edge of the baffle is
between 1/4 inch [213] below the condenser and 1
1/2 inches above the bottom of the condenser and
that there is 1/4 inch or less clearance [15] between
the rear of the condenser and the baffle.
- For the best cooling performance, the baffle
should be 1/4 inch below the bottom of the
condenser.
- If the depth of the enclosure is more than 26 inches [27],
install a wood or an aluminum or galvanized steel sheet
solid box baffle [21] between the lower intake vent and
the upper exhaust vent (See Art01593).
Installation Manual 6
- Make sure that the solid box baffle is the full width
of the inside of the enclosure.
- Make sure that the bottom of the solid box baffle is
18 inches to 18 1/2 inches above the bottom of the
enclosure [17] (4 1/4 inches to 4 3/4 inches above
the top of the lower intake vent opening REF) [18] .
- Make sure that the back of the solid box baffle is
perpendicular to the bottom of the enclosure.
- Make sure that the horizontal top of the solid box
baffle is even with the bottom edge of the upper
exhaust vent [24].
- Make sure that the vertical top edge of the baffle is
between 1/4 inch [213] below the condenser and 1
1/2 inches above the bottom of the condenser.
- Make sure that there is 1/4 inch or less clearance
[15] between the rear of the condenser and the
baffle.
Install Decorative Door Panels (non-metal
door models)
NOTE: The doors are made to accept decorative panels. The
decorative panels must be 3/16 inch or less in thickness.
Install the decorative door panels in the refrigerator
doors before installing the refrigerator in the vehicle.
- Make an upper door panel that is 21 19/32 inches wide x 14
17/32 inches high.
- Make a lower door panel that is:
- 21 19/32 inches wide and
- 31 5/8 inches high (for N62X, N64X, and N64XIM
models) or
- 38 5/8 inches high (for N82X, N84X, and N84XIM
models).
- Pull the panel retainer [37] off each door (See Art00965).
- Push the decorative door panel [38] into the slots of the door
[39].
- Push each panel retainer into the slot on the edge of the
door.