Advertisement
Table of Contents
Sales +44 (0) 8700 766900
Technical +44 (0) 8700 766902
Salus Controls plc
Enterprise Park, Bala
Gwynedd, LL23 7NL
Regional offices, England & Scotland.
Web: www.salus-tech.com
Email: sales@salus-tech.com
Maintaining a policy of continual product
development Salus Controls plc. reserve the right to
change specification, design and materials of
products listed in this brochure without prior notice.
Manual Issue No. IM-RT300RF-001
In st ru ct io n M a nu al
Digital Radio Frequency
THERMOSTAT
for Model No. RT300RF
Thank you for purchasing this Salus product
- if installing for someone else, please ensure that
the instructions are handed to the householder.
Warning - Please read this manual prior to
installation or use.
Shock Hazard
This unit must be installed by a competent person,
in accordance with BS 7671 (the IEE Wiring
Regulations), or other relevant national regulations
and codes of good practice.
Always isolate the AC Mains supply before
installing this unit.
PRIOR TO INSTA
THE INSTALLAT
INTRODUCTION
This thermostat can rep
thermostats and is desig
oil heating control syste
Unlike ordinary single u
type of thermostat sepa
two units. The Receiver
heat on/off control. The
interface and temperatu
linked by Radio Frequen
The RT300RF is easily in
back plate supplied (for
wiring is required when
The back plate can be m
SWITCHES/JUM
The installer should sele
changing from the facto
on the rear of the unit.
Jumpers
Funct
Span
1 mov
temp
(facto
1,2,3,4,5
5 rem
RF ad
conju
corres
The reset button must be
1
Advertisement
Table of Contents
Related Manuals for Salus RT300RF
Summary of Contents for Salus RT300RF
- Page 1 Maintaining a policy of continual product corres development Salus Controls plc. reserve the right to Always isolate the AC Mains supply before change specification, design and materials of installing this unit. The reset button must be products listed in this brochure without prior notice.
-
Page 2: Initial Power-Up
The Control Centre serves as user of the thermostat after reset. interface and temperature sensing/control. The two units are linked by Radio Frequency. The RT300RF is easily installed using the Industry Standard Function Status after Reset back plate supplied (for mounting purposes only as no wiring is required when installing the control centre). - Page 3 WIRING DIAGRAM WIRING THE RECEIVER FOR THE RT300RF FOR 230V APPLICATION 1) Remember to Isolate AC mains supply, note this must be 230V AC and fused at 13 amps max. The unit is default 230V, if volt free application is required you 2) Select a suitable indoor location free from water and must remove link &...
-
Page 4: Installations
3. You must press reset on the control centre afte external thermostat loop into this terminal to avoid assign different address codes for each RT300RF following the ‘RF altering the address code. Switched Live feed back to overloading of the jump Caution : Address Code Setting’... - Page 5 3. You must press reset on the control centre after repeatedly to change the setting, raising or lo 2. Wait for a few seconds. The animated flame (heat call t address codes for each RT300RF following the ‘RF altering the address code. temperature by 0.5˚C per press. The Setpoint...
- Page 6 3 seconds without key ch as filing cabinets, general RF interference The RT300RF will now only • LCD backlight is illuminated throughou press to return to normal ver, the range is enough for most household call for heat if the temperature Setpoint Temperature setting.
-
Page 7: Sleep Mode
SLEEP MODE: PROTECTION: LCD BACKLIGHT: • Press and hold for 3 seconds nd hold BL/FROST for 3 seconds to • LCD backlight is activated when BL/FROST or simultaneously to enter the Sleep mode. e Frost Protection. any key is pressed. The backlight will automatically turn off 5 seconds after all keys •... -
Page 8: Specification
Specification Switch Rating Volt free selectable 230V AC 16 (8)A max Power Supply 2 x AA size Alkaline batteries Operating Temperature 0°C - 50°C Temperature Setting Range 10°C - 35°C in 0.5°C steps Frost Protection Temperature 5°C Temperature Control Accuracy +/- 0.5°C at 25°C Protection Auto cut off at over 35°C...