Advertisement
3.2 Replacing the Battery
The battery should be replaced upon receiving a low battery LCD
indication. A replacement 1.5 V AAA alkaline battery, such as GP
(or equivalent), should be used. Replace the battery as follows:
ON THE REVERSE SIDE
1
OF THE UNIT, SLIDE THE
DIRECTION SHOWN
Figure 2. Battery Removal
AAA
( )
NOTE: INSERT B ATTERY WITH NEGATIVE (--)
EDGE PRESSED AGAINST THE SPRING
4. DEFINING KEYFOB OPTIONS
Note: To enroll the MCT-237, refer to the PowerMax Pro User
Guide section 7 (User Settings) – Enrolling Keyfob Transmitters.
Here you select the function of the two AUX buttons on the
transmitter. Four options are offered for each AUX button:
Status: Pressing the AUX button will cause the control panel's
voice module to announce the system status.
Instant: Pressing the AUX button while the exit delay is in
progress will cause the system to arm "instant" (the entry delay is
canceled).
Skip exit delay: Pressing the AUX button will immediately cause
the system to arm.
PGM / X-10: Pressing the AUX button will activate the PGM
output or X-10 units.
Proceed as shown in the following flow chart.
WARRANTY
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its products hereinafter
referred to as "the Product" or "Products" to be in conformance with its own plans and specifications and to
be free of defects in materials and workmanship under normal use and service for a period of twelve months
from the date of shipment by the Manufacturer. The Manufacturer's obligations shall be limited within the
warranty period, at its option, to repair or replace the product or any part thereof. The Manufacturer shall not
be responsible for dismantling and/or reinstallation charges. To exercise the warranty the product must be
returned to the Manufacturer freight prepaid and insured.
This warranty does not apply in the following cases: improper installation, misuse, failure to follow
installation and operating instructions, alteration, abuse, accident or tampering, and repair by anyone other
than the Manufacturer.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or liabilities, whether
written, oral, express or implied, including any warranty of merchantability or fitness for a particular purpose,
or otherwise. In no case shall the Manufacturer be liable to anyone for any consequential or incidental
damages for breach of this warranty or any other warranties whatsoever, as aforesaid.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any person
to act on its behalf in the modification, variation or extension of this warranty. This warranty shall apply to the
Product only. All products, accessories or attachments of others used in conjunction with the Product,
including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall not be liable
for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or otherwise,
caused by the malfunction of the Product due to products, accessories, or attachments of others, including
batteries, used in conjunction with the Products.
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 65 WEST DUDLEY TOWN ROAD, BLOOMFIELD CT. 06002-1376. PHONE: (860) 243-0833, (800) 223-0020. FAX: (860) 242-8094
VISONIC LTD. (UK): FRASER ROAD, PRIORY BUSINESS PARK, BEDFORD MK44 3WH. PHONE: (0870) 7300800 FAX: (0870) 7300801
INTERNET: www.visonic.com
VISONIC LTD. 2006
MCT-237
2
COVER IN THE
EXTRACT THE BATTERY
2
FROM ITS HOLDER
TEST THE UNIT BY MOMENTARILY
PRESSING ONE OF THE TRANSMIT
SWITCHES. THE LCD DISPLAY
SHOULD LIGHT.
2
INSERT THE
( )
NEW B ATTERY
1
D-300280 (REV. 0, 06/06)
Figure 3. Inserting New Battery
3.3 Cleaning
The transmitter may get dirty if touched with greasy fingers. Clean
it only with a soft cloth or sponge moistened lightly with a mixture
of water and mild detergent, and wipe it dry immediately.
The use of abrasives of any kind is strictly forbidden. Also
never use solvents such as kerosene, acetone or thinner.
READY 00:00
17: AUX BUTTON A
NORMAL MODE
status
instant
skip exit delay
USER SETTINGS
PGM / X-10
INSTALLER MODE
ENTER CODE
[installer code]
1. NEW INSTL CODE
Note: The currently saved
2. ENROLLING
options are displayed with
dark box at the right side of
3. DEFINE ZONES
the display. To review the
options, repeatedly click
4. DEFINE PANEL
PowerMax Pro control
panel until the desired
option is displayed. Then,
click OK (a dark box will be
<OK> TO EXIT
displayed at the right side).
Figure 4: Performing PowerMax Pro Audio Functions
The Manufacturer does not represent that its Product may not be compromised and/or circumvented, or that
the Product will prevent any death, personal and/or bodily injury and/or damage to property resulting from
burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or
protection. User understands that a properly installed and maintained alarm may only reduce the risk of
events such as burglary, robbery, and fire without warning, but it is not insurance or a guarantee that such
will not occur or that there will be no death, personal damage and/or damage to property as a result.
The Manufacturer shall have no liability for any death, personal and/or bodily injury and/or damage
to property or other loss whether direct, indirect, incidental, consequential or otherwise, based on a
claim that the Product failed to function. However, if the Manufacturer is held liable, whether directly or
indirectly, for any loss or damage arising under this limited warranty or otherwise, regardless of cause or
origin, the Manufacturer's maximum liability shall not in any case exceed the purchase price of the Product,
which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive
remedy against the Manufacturer.
Warning: The user should follow the installation and operation instructions and among other things test the
Product and the whole system at least once a week. For various reasons, including, but not limited to,
changes in environmental conditions, electric or electronic disruptions and tampering, the Product may not
perform as expected. The user is advised to take all necessary precautions for his /her safety and the
protection of his/her property.
6/91
SLIDE THE
COVER BACK ON
3
IN THE DIRECTION
SHOWN
18: AUX B 2-W-KF
status
instant
skip exit delay
PGM / X-10
or
on the
D-300280
Advertisement
