Polaris Dragon Owner's Manual
  1. Manuals
  2. Brands
  3. Polaris Manuals
  4. Snowmobiles
  5. Dragon
  6. Owner's manual

Polaris Dragon Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Polaris Dragon

Summary of Contents for Polaris Dragon

  • Page 3 WARNING Read, understand, and follow all of the instructions and safety precautions in this manual and on all product labels. Failure to follow the safety precautions could result in serious injury or death. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
  • Page 4 Polaris enthusiasts. Be sure to visit us online at www.polarisindustries.com for the latest news, new product introduc- tions, upcoming events, career opportunities and more. Here at Polaris we proudly produce an exciting line of utility and recre- ational products. • Snowmobiles •...
  • Page 5 POLARIS and POLARIS THE WAY OUT are registered trademarks of Polaris Indus- tries Inc. Copyright 2006 Polaris Sales Inc. All information contained within this publication is based on the latest product information at the time of publication. Due to constant...

  • Page 6: Table Of Contents

    Polaris Products..... . . 114 Troubleshooting ..... . . 115 Warranty .

  • Page 7: Introduction

    Remove the spare key and store it in a safe place. Your key can be duplicated only by mating a Polaris key blank with one of your existing keys, so if both keys are lost, the ignition switch must be replaced.

  • Page 8: Air Pollution

    Polaris snowmobiles are engineered to conform to these SAE standards. Our muffler systems are designed to reduce noise levels and must not be altered or removed. The sound of your snowmobile may not be welcome to non-snowmobilers, so you have a responsibility to operate your snowmobile with concern for others.

  • Page 9: Safety

    SAFETY Operator Safety The following signal words and symbols appear throughout this manual and on your vehicle. Your safety is involved when these words and sym- bols are used. Become familiar with their meanings before reading the manual. The safety alert symbol, on your vehicle or in this manual, alerts you to the potential for injury.
  • Page 10 Always check major and vital safety components before every ride. All Polaris snowmobiles are designed and tested to provide safe operation when used as directed. Failure of critical machine components may result from operation with any modifications, especially those that increase speed or power.

  • Page 11: Riding Position

    SAFETY Operator Safety Stay Clear of Track Your snowmobile is propelled by a revolving track that must be partially exposed for proper operation. WARNING Serious injuries may result if hands, feet, or clothing become entangled in the track. Be alert when riding, and remain properly seated to stay clear of the track.

  • Page 12: Riding Apparel

    Eye Protection Do not depend on eyeglasses or sunglasses for eye protection. When- ever riding a Polaris vehicle, always wear shatterproof goggles or use a shatterproof helmet face shield. Polaris recommends wearing approved Personal Protective Equipment (PPE) bearing markings such as VESC...

  • Page 13: Disabled Operators

    SAFETY Operator Safety Disabled Operators Safe operation of this rider-active vehicle requires good judgement and physical skills. Operators with cognitive or physical disabilities have an increased risk of loss of control, which could result in serious injury or death. Survival Preparation For your safety, always ride in a group of other snowmobilers.

  • Page 14: Rider Capacity

    A decal on the console of these models indicates single rider operation. Driving 2-Up - Some Polaris snowmobiles are designed for up to two riders. A decal on the hood of these models indicates that the vehicle is designed for one operator and one passenger only.

  • Page 15: Driver Awareness

    SAFETY Operator Safety Driver Awareness Slow down when traveling near poles, posts, or other obstacles. Be especially alert if you're snowmobiling after dark. Always be on the alert for wire fences. Single strands are especially dangerous, since there may be a great distance between posts.
  • Page 16 SAFETY Operator Safety Avalanches Snowmobilers should always be properly trained and equipped before traveling in mountainous terrain: • Take an avalanche class • Travel with experienced people • Travel on designated trails • Make sure each person is equipped with a shovel, probe and avalanche beacon.

  • Page 17: Ice And Snow Build-Up

    SAFETY Operator Safety Ice and Snow Build-up WARNING Ice and snow build-up may interfere with the steering of your machine, result- ing in serious injury or death. Keep the underhood area free of snow and ice. Before driving, manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering.

  • Page 18: Driving Downhill

    SAFETY Operator Safety Driving Downhill When riding downhill, shift your weight to the rear of the machine and reduce your speed to a minimum. Apply just enough throttle to keep the clutch engaged, allowing the engine's compression to help slow the machine and keep it from rolling freely downhill.

  • Page 19: Driving In Hilly Terrain

    SAFETY Operator Safety Driving in Hilly Terrain WARNING Climbing a hill or crossing the face of a slope may result in loss of balance and machine roll-over, causing serious injury or death. Use caution and good judgement when driving in hilly terrain. Use extra caution when operating in hilly terrain.

  • Page 20: Drive Belt

    SAFETY Operator Safety Drive Belt Do not operate the engine with the drive belt removed. Any servicing that requires operation without a belt must be performed by your dealer. Operation of the engine with the belt removed may result in injury or damage to the engine. Intake Silencer Do not operate the engine with the intake silencer or filter removed.

  • Page 21: Inadequate Snow Conditions

    SAFETY Operator Safety Inadequate Snow Conditions WARNING Do not drive for prolonged periods on blacktop, gravel, or ice. Doing so could cause irreversible track damage and lead to serious injury. Since snow provides the only lubrication for the power slide suspension and, on liquid cooled models, cooling for the engine, adequate snow cover is a requirement for operation of your machine.

  • Page 22: Driving Responsibly

    SAFETY Operator Safety Driving Responsibly Every snowmobile handles differently, and even the most docile condi- tions may become dangerous if operators drive improperly. If you're new to snowmobiling, acquaint yourself with the machine and with what it will and won't do under various conditions. Even seasoned driv- ers should spend some time getting the feel for a machine before attempting ambitious maneuvers.
  • Page 23 SAFETY Operator Safety Windchill/Temperature Charts The following information is provided to help you determine when tem- peratures become dangerous for riding. WINDCHILL CHART (_F) Wind Actual Thermometer Reading (_F) Speed -10 -15 -20 -25 -30 -35 -40 -45 Equivalent Temperature (_F) Calm -10 -15 -20 -25 -30 -35 -40 -45 -11 -16 -22 -28 -34 -40 -46 -52 -57 -63...

  • Page 24: Clutch Cover Warning

    If any decal becomes illegible or comes off, contact your Polaris dealer to purchase a replacement. Replacement safety decals are provided by Polaris at no charge.

  • Page 25: Track Warning

    SAFETY Safety Decals and Locations Track Warning The track warning decal is on the rear of the tunnel: Stay clear of track. Do not sit on seat back. Entanglement with the track or a fall from seat back may result in severe injury or death. Passenger Warnings The passenger warning decal is located on the left side of the...

  • Page 26: Reverse Warning

    SAFETY Safety Decals and Locations Reverse Warning The reverse warning decal is located on the console, either below the windshield or beside the steering post: WARNING Reverse operation, even at low speeds, can cause loss of control resulting in serious injury or death.
  • Page 27 • To avoid serious injury or death, read and understand all warnings and the Owner's Manual before operation. If manual is missing, con- tact a Polaris dealer for a replacement. • This vehicle is capable of high speeds. Buried objects or uneven terrain can cause loss of control.

  • Page 28: Features

    FEATURES 1. Hood 8. Snow Flap 2. Headlight 9. Console Storage Compartment 3. Windshield 10. Suspension 4. Handlebar 11. Track 5. Operator Seat 12. Skis 6. Taillights 13. Nosepan 7. Rear Bumper 14. Front Bumper...
  • Page 29 FEATURES 1. Fuel Filler Cap 2. Ignition Switch 3. Brake Lever 4. Headlight Adjuster 5. MFD Gauge 6. Engine Stop Switch 7. Throttle Control 8. Hood Hold Down Straps 9. Recoil Starter Handle 10. Parking Brake 11. Handlebar Grip Warmer Switch 12.

  • Page 30: Adjustable Headlights

    In extreme conditions the DET sys- tem retards timing and holds it in a retarded state. If this occurs, replace the fuel with recommended fuel or see your Polaris dealer for service. Cause of DET Activation...
  • Page 31 FEATURES Instrumentation MFD Component Identification Item 1 Analog (if equipped) 2 Digital Gauge 3 CHECK ENGINE Indicator (carb models) 4 Low Oil Indicator 5 High Temp Indicator 6 Brake Indicator 7 Reverse Indicator 8 High Beam Indicator Digital Display Identification Item 1 RPM or Speed Altitude (if equipped)

  • Page 32: Mfd Settings

    FEATURES Instrumentation MFD Settings With the engine running, use the MFD Control Switch to set the MFD display to your preference. The rocker switch ( ) has a MODE but- ton (top) and a SET button (bottom). Standard vs. Metric The MFD will display either stan- dard or metric units of measurement.
  • Page 33 FEATURES Instrumentation MFD Digital Display Programs Press the MODE button to cycle through the three MFD programs: Per- formance, Engine and History. Each program will remain in the display until another is selected. NOTE: The analog will always display either MPH or engine RPM (whichever setting is selected) regardless of the display pro- gram being viewed.
  • Page 34 FEATURES Instrumentation MFD Digital Display Programs Trip Settings Trip 1 and Trip 2 are odometers used to check fuel mileage or to keep track of distance traveled. 1. To reset a trip odometer to zero, enter the Trip 1 or Trip 2 display. 2.
  • Page 35 FEATURES Instrumentation MFD Digital Display Programs Performance Program Clock Setting 1. While in the CLOCK display, press and hold the SET button for five seconds. 2. When the hour starts flashing press the SET switch once to advance one hour, or press and hold the SET button to advance the hour once every 0.2 seconds.
  • Page 36 FEATURES Instrumentation MFD Digital Display Programs Engine Program The Engine Program automatically displays the engine coolant tempera- ture, engine hours, electrical system voltage level and fuel level (if equipped). On machines equipped with altimeter sensor and ambient air temperature sensors, altitude and ambient air temperature will display as additional screens in the engine program.
  • Page 37 FEATURES Instrumentation MFD Digital Display Programs Engine Program Altitude (if equipped) The rider can calibrate the altimeter for current atmospheric conditions. Altimeter accuracy will be +/-300 ft. (91 m) after adjustment. NOTE: Press and hold the MODE switch for ten seconds to switch between stan- dard and metric units of measure- ment.
  • Page 38 FEATURES Instrumentation MFD Digital Display Programs History Program The History Program automatically displays electrical system voltage level and fuel level (if equipped). While in the History mode, press the SET button to view maximum vehicle speed, maximum engine rpm or the current service interval set- ting.
  • Page 39 FEATURES Instrumentation MFD Digital Display Programs Service Interval Reminder The gauge logs the number of engine hours between service reminders. When the logged hours reaches the designated service interval (set by the user), the gauge provides a reminder that service is due. "SErVCE" will flash in the odometer area and "ENG"...
  • Page 40 FEATURES Instrumentation MFD Battery Replacement (models with clocks) If the clock function of the MFD isn't working properly, replace the battery. Replacement batteries are available from your dealer. 1. Remove the plenum from the under- side of the hood. 2. Locate the black battery compart- ment.

  • Page 41: Gauge Cleaning

    FEATURES Instrumentation MFD Battery Replacement (models with clocks) 6. Install a new battery with fingers only. 7. Seal the end of the battery compartment using high strength double- sided tape between the two compartment halves or high strength single-sided tape around the outside of the compartment. 8.

  • Page 42: The Perfect Fit

    THE PERFECT FIT Front Suspension Adjustments Independent Front Suspension (IFS) Break in the suspension for about 150 miles (240 km) before making any fine-tuning adjustments. Settings will vary from rider to rider, depending on rider weight, vehicle speed, riding style, and trail conditions. We recommend starting with factory settings and then customizing each adjustment individually to suit rider preference.
  • Page 43 THE PERFECT FIT Front Suspension Adjustments Shock Spring Preload Increasing spring preload will increase ski-to-ground pressure. Decreasing spring preload will decrease ski-to- ground pressure. When adjusting, be sure the springs on both the left and right sides of the machine are at the same adjustment.
  • Page 44 Changing shock valving requires special tools and a sound knowledge of mechanical theory, tool use, and shop procedures to perform the work safely and correctly. Shocks contain high-pressure nitrogen gas. Use extreme cau- tion when handling high-pressure service equipment. We recommend that this work be performed by a Polaris dealer.
  • Page 45 A suspension set up for trail riding would bot- tom out harshly on a snowcross course. See your Polaris dealer for initial suspension setup information. Addi- tional adjustments can be made after initial setup. Make adjustments to one area at a time so you can evaluate the change.

  • Page 46: Suspension Performance Tips

    Bogie wheel kits are available from your dealer. • Polaris offers track kits for improved flotation in deep snow. See your dealer for assistance. NOTE: Keep the suspension pivot points lubricated. This will reduce moisture and rust build-up and ensure proper function of the suspension components.
  • Page 47 THE PERFECT FIT Rear Suspension Adjustments Initial Spring Preload Setting (Sag Method) To set up the rear suspension torsion spring preload, measure the distance between the ground and rear bumper. This is measurement X. Take the first measurement with no rider and with the rear suspension at full extension.
  • Page 48 THE PERFECT FIT IQ Rear Suspension Adjustments Torsion Spring Preload To adjust rear torsion spring preload, rotate the three-position cam using the engine spark plug tool. Adjustment is easiest when the cam is rotated from low to medium, and then to high. Rotating directly from low to high will require significantly more effort.
  • Page 49 THE PERFECT FIT IQ Rear Suspension Adjustments Rear Shock Compression Damping Turn the adjustment knob on the shock reservoir to make adjustments to the compression damping. Positions are labeled on the shock. When adjusting, we recommend that you turn the adjuster slightly, then test ride.

  • Page 50: Suspension Coupling

    IQ Rear Suspension Adjustments Suspension Coupling On all Polaris snowmobile rear suspensions, there are two torque arms that control the movement of the rail beam. Prior to the advent of sus- pension coupling, these torque arms could move independently of each other.
  • Page 51 THE PERFECT FIT IQ Rear Suspension Adjustments Rear To Front Coupling Using the Rear Rear Scissor Stop (RRSS) The rear rear scissor stop (RRSS) couples the movement of the rear torque arm with the front torque arm and limits the amount of indepen- dent movement between the rear torque and the front torque arm.
  • Page 52 THE PERFECT FIT IQ Rear Suspension Adjustments Weight Transfer During Acceleration The preferred method for control- HIGH ling weight transfer during accel- eration is by adjusting the rear rear scissor stop (RRSS). The factory setting is the best for most trail MEDIUM riding conditions.

  • Page 53: Handlebar Adjustments

    THE PERFECT FIT Handlebar Adjustments When making handlebar adjustments, always be sure the handlebars, brake lever and throttle lever operate smoothly and do not contact the fuel tank, windshield or any other part of the vehicle when the handle- bars are turned fully to the left or right. Handlebar Angle Follow these steps to adjust handlebar angle at the handlebar...
  • Page 54 THE PERFECT FIT Accessories Polaris offers a wide range of accessories for your snowmobile to help make each ride more enjoyable. Use only Polaris parts and accessories on your Polaris snowmobile. Use of unapproved parts and accessories may result in: •...

  • Page 55: Traction Products

    Before equipping your machine with traction products, be aware of the laws in your area pertaining to the use of traction products. Use only Polaris traction products on your snowmobile. Track warran- ties are void if track damage or failure results from improper or exces- sive stud installation or the use of non-Polaris traction products.

  • Page 56: Wear Strips

    THE PERFECT FIT Traction Products nCarbide Skags A skag is a replaceable bar attached to the underside of the ski to assist in turning the snowmobile and to prevent ski wear caused by contact with roads and other bare terrain. Use carbide skags with studded tracks to help maintain proper vehicle steering and control.

  • Page 57: Pre-Ride Inspections

    PRE-RIDE INSPECTIONS Pre-Ride Checklist Inspect all items on the checklist for proper operation or condition before each use of the snowmobile. Procedures are outlined on the refer- enced pages. Look for a checkmark (n) on the referenced pages to locate the pre-ride inspection items. Item See Page Drive Belt Condition...

  • Page 58: Throttle Lever

    PRE-RIDE INSPECTIONS Before Starting the Engine WARNING Worn, damaged, or malfunctioning components may cause serious injury or death. Before starting the engine, check all components to be sure of proper operation. Read and Understand Your Owner's Manual Read the Owner's Manual completely and refer to it often. The manual is your guide to safe and enjoyable snowmobiling experience.

  • Page 59: Brake Lever Travel

    PRE-RIDE INSPECTIONS Before Starting the Engine n Brakes Always check the following items for proper operation before starting the engine. Brake Lever Travel Squeeze the brake lever. It should move no closer to the (1.3 cm) handgrip than 1/2I (1.3 cm). A smaller distance indicates low brake fluid level or air in the hydraulic system.

  • Page 60: Parking Brake Lever Lock

    PRE-RIDE INSPECTIONS Before Starting the Engine n Parking Brake Lever Lock Use the parking brake lever lock only when you want the machine to remain stationary; for example, when parked on an incline for a period of five minutes or less. 1.

  • Page 61: Steering System

    PRE-RIDE INSPECTIONS Before Starting the Engine n Steering System WARNING Ice and snow build-up may interfere with the steering of your machine, result- ing in serious injury or death. Keep the underhood area free of snow and ice. Before driving, manually turn the skis to the left and right to be sure ice and snow are not interfering with full left and right steering.

  • Page 62: Recoil Rope

    Recoil Rope Inspect the recoil rope and handle for excessive wear, and make sure the knot securing the rope inside the handle is secure. If excessive wear is found, see your Polaris dealer for replacement.
  • Page 63 PRE-RIDE INSPECTIONS Start the Engine and Check Engine Stop Switch Check the auxiliary shut-off switch for proper operation. Push the switch down to stop the engine. Pull it up to allow restarting. Ignition Switch Make sure the engine stops when the ignition switch is turned to OFF. Tether Switch (if equipped) If your machine has a tether switch, remove the tether from the switch to make sure the engine stops immediately.

  • Page 64: Operation

    OPERATION Starting the Engine WARNING Before starting the engine, always refer to all safety warnings pertaining to snowmobile operation. Never start your snowmobile without checking all components to be sure of proper operation. See Before Starting the Engine beginning on page 55. 1.

  • Page 65: Engine Break-In

    Premix the first tank of fuel with one pint of Polaris injection oil for each five gal- lons of fuel. This, in addition to the lubrication supplied by the injection system, will assure proper engine break-in.

  • Page 66: Oil Injection System

    This snowmobile is equipped with a variable exhaust system (VES). Engine lubrication comes from oil added to the fuel and oil injection systems. Polaris recommends the use of VES II 2 Cycle Oil for this engine. See page 114 for the part numbers of Polaris products.

  • Page 67: Track Warm-Up

    OPERATION Track Warm-Up WARNING A loose track or flying debris could cause serious injury or death. Stand clear of the front of the machine and the moving track. Never hold the snowmobile up or stand behind it while warming up the track. Do not use excessive throt- tle during warm-up or when the track is free-hanging.

  • Page 68: Slide Rail And Track Cooling

    OPERATION Slide Rail and Track Cooling CAUTION Inadequate cooling and lubrication will lead to overheating of the slide rail and track, resulting in premature wear and failure. Reduce speeds and fre- quently drive into fresh snow to allow adequate cooling and polishing of the slide rail and track surfaces.

  • Page 69: Fuel System Deicers

    OPERATION Fuel For peak performance, Polaris recommends the use of 91 octane or higher fuel. Although 87 octane fuel is usable, some engine perfor- mance will be lost and fuel economy will decrease. Do not use lower than 87 octane fuel. Do not use fuel containing more than 10% ethanol (including E85).

  • Page 70: Low Oil Indicator Light

    Never operate the engine if oil is not visible in the tank. NOTE: The Polaris oil cap on the oil tank is vented to allow proper oil flow. See your Polaris dealer for recommended replacement parts.

  • Page 71: Engine Stop Switch

    OPERATION Engine Stop Switch Push down on the engine stop switch ( ) to ground out the ignition and stop the engine quickly. Pull the switch up to the ON position to allow restarting. Throttle Safety Switch The throttle safety switch is designed to stop the engine whenever all pressure is removed from the throttle lever and the throttle cable or valves do not return to the normal closed position.
  • Page 72 When these switches are disconnected, the ignition key switch must be used to shut off the engine. DO NOT continue to operate the machine with the throttle safety switch disconnected. Return the machine to an authorized Polaris dealer for service as soon as possible.

  • Page 73: Emergency Stopping

    OPERATION Emergency Stopping The following chart lists methods for stopping the snowmobile in the event of an emergency. See page 68 for more information about the engine stop switch and throttle safety switch. SYSTEM WHAT IT DOES Ignition Switch Interrupts ignition circuit Brake Slows jackshaft Engine Stop Switch...

  • Page 74: Emergency Starting

    OPERATION Emergency Starting If the recoil starter system fails, use the emergency start strap to start the engine. 1. Open the hood. 2. Remove the left side panel. 3. Using the belt removal tool (L-wrench), follow the direc- tions on the air box to relieve belt tension.
  • Page 75 OPERATION Electronic Reverse (PERCt) Electronic reverse will activate only if the engine RPM is below 4000. WARNING Improper reverse operation, even at low speeds, may cause loss of control, resulting in serious injury or death. Damage will occur to the chaincase or transmission if shifting is attempted when the engine is operating above idle speed.
  • Page 76 OPERATION Daily Storage At the end of each ride, park the snowmo- bile on a level surface and support it at the rear with an appropriate track stand. The track should be suspended approximately 4I (10 cm) off the ground. Remove the key and cover the machine.

  • Page 77: Maintenance

    MAINTENANCE Emission Control Information Any qualified repair shop or qualified person may maintain, replace, or repair the emission control devices or systems on your snowmobile. Emission Control Label Your snowmobile is equipped at the time of sale with an emission con- trol information (ECI) label and a factory-installed emissions informa- tion hangtag.
  • Page 78 The speci- fied maintenance for the fuel filter is recommended additional emission- related maintenance. Polaris recommends that you contact an authorized Polaris dealer to perform any service that may be necessary.
  • Page 79 Personal safety is critical when attempting to service or make adjust- ments to your snowmobile. If you're not familiar with safe service or adjustment procedures and the use of tools, or if you don't feel comfort- able performing these tasks yourself, contact an authorized Polaris dealer for service. CAUTION Hot components can cause damage to plastic.

  • Page 80: Coolant Level

    The following chart is a guide based on average riding conditions. You may need to increase frequency based on riding conditions. When inspection reveals the need for replacement parts, always use genuine Polaris parts, available from your Polaris dealer. Item Frequency Page 150 mi.

  • Page 81: Auxiliary Shut-Off Switch (Engine Stop Switch)

    MAINTENANCE Periodic Maintenance Interval Table Item Frequency Page 150 mi. 500 mi. 1000 mi. 2000 mi. Pre- (240 km) (800 km) (1600 km) (3200 km) Season BRAKES Hose Routing Hose Condition Fluid Leaks Brake Pads Brake Disc Parking Brakes Brake System 56, 91 Brake Fluid FUEL MANAGEMENT...

  • Page 82: Suspension Mounting Bolts

    MAINTENANCE Periodic Maintenance Interval Table Item Frequency Page 150 mi. 500 mi. 1000 mi. 2000 mi. Pre- (240 km) (800 km) (1600 km) (3200 km) Season CHASSIS Ski Toe Alignment Suspension Mounting Bolts Steering Fasteners Rear Suspension Fasteners Suspension Shock Oil Cooling Fins and Shroud Drive Shaft Bearing...

  • Page 83: Front Suspension

    The front suspension does not require lubrication. Rear Suspension Lubricate the suspension pivot shafts with Polaris Premium All Season Grease at 500 miles (800 km) initially, every 1000 miles (1600 km) after that, and before off-season storage each year. Lack of lubrication will adversely affect your ride and the life of the suspension.

  • Page 84: Throttle Cable

    MAINTENANCE Lubrication Driveshaft Bearing Inject grease into the fitting on the speedometer sensor housing until grease purges from the seal on the inside of the tunnel. This should take approximately two pumps. Do not use more than four pumps. Throttle Cable Lubricate the throttle cable lightly with grease or oil.

  • Page 85: Chaincase Oil

    500 miles (800 km), then every 1000 miles (1600 km) or seasonally. Polaris recommends the use of Polaris Synthetic Chaincase Lube. See page 114 for the part numbers of Polaris products. Oil Check 1. Position the vehicle on a level sur- face.

  • Page 86: Oil Lines

    MAINTENANCE Lubrication Chaincase Oil Oil Change 1. Position the vehicle on a level surface. 2. Remove the drain plug (4) and drain the oil into a drain pan. Allow the oil to drain completely. 3. Clean off all metal shavings from the plug.

  • Page 87: Spark Plugs

    MAINTENANCE Spark Plugs A new engine can cause temporary spark plug fouling due to the preser- vative added during the assembly process. Avoid prolonged idle speeds, which cause plug fouling and carbonization. Refer to your Owner's Manual Supplement for the specific spark plug to be used in your machine.

  • Page 88: Spark Plug Condition

    MAINTENANCE Spark Plug Condition Spark plug condition is indicative of engine operation. The spark plug firing end condition should be read after the engine has been warmed up and the vehicle has been driven at higher speeds. Immediately check the spark plug for correct color.

  • Page 89: Intake Filters

    Do not attempt to service the fuel pump. Fuel Filter/Fuel Lines See your Polaris dealer for replacement of the fuel filter at the intervals outlined in the Periodic Maintenance Table beginning on page 77. Inspect the fuel lines regularly for signs of deterioration or damage.

  • Page 90: Cooling System

    Please see your Polaris dealer. When adding or changing coolant, Polaris recommends using Premium 60/40 anti-freeze coolant, which is already premixed and ready to use. Do not dilute with water. Never exceed a 60% antifreeze/40% water mixture.
  • Page 91 This service must be performed when the engine is cold. Ask your Polaris dealer to check the coolant when he performs the fall tune-up on your snowmobile.
  • Page 92 MAINTENANCE Cooling System Bleeding the Cooling System WARNING Steam and hot liquids will cause serious burns to your skin. Never bleed the cooling system or remove the pressure cap when the engine is warm or hot. Use of a non-standard pressure cap will not allow the recovery system to function properly.

  • Page 93: Exhaust System

    MAINTENANCE Exhaust System Check the exhaust system for wear or damage at approximately 2000 miles (3200 km). Always allow the engine and exhaust system to cool completely before inspecting. WARNING Hot exhaust system parts can cause serious burns. Allow adequate time for the exhaust system to cool.

  • Page 94: Brake Components

    3. Brake Pad Material (Replace when thickness is less than 1/16I/1.5 mm). Excessive Lever Travel Hydraulic brakes are self- adjusting, but if excessive brake pad clearance develops, bring the machine to an autho- rized Polaris dealer for inspec- tion and adjustment.

  • Page 95: Brake Fluid

    If the fluid is sufficient, the sight glass will be black. If the sight glass is any color other than black, add brake fluid. Replace brake fluid at least every two years with Polaris DOT 4 high temperature brake fluid. See page 114 for the part numbers of Polaris products.
  • Page 96 MAINTENANCE Brakes Bleeding the Hydraulic Brake System Air in the hydraulic brake system will cause spongy brake lever action. Bleed the system before operating the snowmobile. WARNING Operating the vehicle with a spongy brake lever can result in loss of brakes, which could cause an accident and lead to serious injury or death.

  • Page 97: Headlight Bulb Removal

    MAINTENANCE Lights NOTE: Do not touch a halogen bulb with bare fingers. Oil from skin leaves a residue, causing a hot spot that will shorten the life of the lamp. If fingers do touch the bulb, clean it with an alcohol- moistened towel.
  • Page 98 MAINTENANCE Lights Headlight Bulb Installation 1. Hold the bulb by its metal base and install it into the wire harness. NOTE: Recommended replacement bulbs include H4, HB2 and 9003 bulbs. 2. Insert the bulb into the housing. 3. Connect the spring to the housing. 4.
  • Page 99 Polaris dealer. Any unauthorized modifications to clutches, such as adding or removing weights, will void the warranty. CAUTION The bushings in the weights and rollers of Polaris clutches are made of a material that may be damaged if lubricated. Do not lubricate clutch bushings. Clutch Alignment Offset Clutch alignment offset is important for maintaining optimum perfor- mance.
  • Page 100 Drive Belt Belt width and length must match the center distance of the clutches and sheave width of the drive clutch. Polaris recommends the use of O.E.M. belts. Other belts may match the dimensions, but can drastically change the shift pattern, resulting in poor performance. See Drive Belt Trouble- shooting on page 119.

  • Page 101: Drive Belt Removal

    MAINTENANCE Clutch System Drive Belt Removal CAUTION Do not attempt to remove the drive belt after operating in reverse. The snow- mobile must be stopped after forward motion to prevent damage to compo- nents during belt removal. Rotate the driven clutch counterclockwise 1/4 turn by hand to ensure forward engagement before attempting to remove the belt.

  • Page 102: Drive Belt Installation

    MAINTENANCE Clutch System Drive Belt Installation 1. Drop the drive belt over the drive clutch and pull back the slack. NOTE: To ensure satisfactory belt life, install belts so they operate in the same direction of rotation by positioning the identifica- tion numbers so that you can read them.

  • Page 103: Drive Belt Deflection

    MAINTENANCE Clutch System n Drive Belt Deflection Measure belt deflection with both clutches at rest and in their full neutral position. Place a straight edge (1) on the belt and apply downward pressure while measuring at point 2. This measurement should be 1 1/4I (3.2 cm).

  • Page 104: Torque Stop

    MAINTENANCE Clutch System Torque Stop Periodically check torque stop clearance. With clutches in proper align- ment, measure rear torque stop clearance from the engine case. Clear- ance should be .010I-.030I (.25-.75mm). Adjust if necessary. Lock the jam nut. Rear Torque Stop .010 -.030 (.25-.75 mm)
  • Page 105 MAINTENANCE Fall Tune-Up For maximum performance, arrange for a fall service tune-up with your Polaris dealer. His experienced and trained service technician will keep your machine in peak operating condition. Track Maintenance Track Inspection WARNING Broken track rods can cause a rotating track to come off the machine, which could cause serious injury or death.

  • Page 106: Track Lubrication

    MAINTENANCE Track Maintenance Track Lubrication WARNING Operating with insufficient lubrication between the rail slide and track guide clips can cause track failure, loss of vehicle control and loss of braking ability, which can result in serious injury or death. Avoid operating for extended peri- ods on ice and other surfaces that have little or no snow for lubrication.

  • Page 107: Track Tension

    MAINTENANCE Track Maintenance WARNING Moving parts can cut and crush body parts. When performing the checks and adjustments recommended on the following pages, stay clear of all moving parts. Never perform track measurement or adjustments with the engine run- ning. Track Tension Track adjustment is critical for proper handling.
  • Page 108 MAINTENANCE Track Maintenance Track Tension 4. Check for specified slack between the wear surface of the track clip and the plastic slider. Refer to the Track Tension Data Chart on page 104. If the track needs adjustment: 5. Loosen the rear idler shaft bolt. 6.

  • Page 109: Track Alignment/Condition

    MAINTENANCE Track Maintenance n Track Alignment Periodically check that the track is centered and running evenly on the slide rails. Misalignment will cause excessive wear to the track and slide rail. 1. Safely support the rear of the machine with the track off the ground. 2.
  • Page 110 MAINTENANCE Steering System Steering Inspection and Adjustment Each week, or before a long ride, check all steering system fasteners and tighten if necessary.

  • Page 111: Ski Alignment

    Improper ski alignment or adjustment may cause loss of steering control, resulting in serious injury or death. Do not attempt to change the ski align- ment or camber adjustment. See your Polaris dealer. With the handlebars in a straight ahead position, and with vehicle weight compressing the suspension, measure from the straight edge of the skis at the center of the ski mounting bolt.

  • Page 112: Ski Skags

    MAINTENANCE Steering System n Ski Skags WARNING Worn skis and/or skags will adversely affect handling. Loss of vehicle control may result, causing serious injury or death. See your dealer's studding chart for recommended skags. If you install longer or more aggressive carbide skags than the original equipment, it may also be necessary to add track studs to maintain proper vehicle control while turning on hard-packed snow or ice.

  • Page 113: Rail Slide Condition

    MAINTENANCE Steering System n Rail Slide Wear Measure slide thickness at several points along the rail. 7/16 Have your dealer replace the (1.1 cm) slide when it's worn down to the top of the wear limit indicator groove ( ). Do not operate the snowmobile if slide thickness measures less than 7/16I (1.1 cm).

  • Page 114: Cleaning And Preservation

    Extended Storage Off-season or extended storage of your snowmobile requires preventive measures to aid against deterioration and to prolong the useful life of many components. See page 114 for the part numbers of Polaris prod- ucts. Cleaning and Preservation Proper storage starts with cleaning, washing, and waxing the hood, chassis, and plastic parts.

  • Page 115: Clutch And Drive System

    MAINTENANCE Extended Storage Bearings Grease the drive shaft clutch side bearing with Polaris Premium All- Season Grease or a similar high quality grease to prevent corrosion. Clutch and Drive System Remove the drive belt and store in a cool dry location. Do not lubricate clutch components, except the driven clutch shaft bushing as outlined in the Master Repair Manual.

  • Page 116: Electrical Connections

    MAINTENANCE Extended Storage Electrical Connections Replace worn or frayed electrical wire and connectors. Be sure wiring harness is properly secured away from sharp edges, steering linkage, moving parts, and hot exhaust parts. Transporting the Snowmobile Whenever the snowmobile is transported: 1.

  • Page 117: Polaris Products

    POLARIS PRODUCTS Part No. Description Engine Lubricants 2870791 Fogging Oil (12 oz. Aerosol) 2871098 Premium 2-Cycle Engine Oil (qt.) 2871097 Premium 2-Cycle Engine Oil (gal.) 2871240 Premium 2-Cycle Engine Oil (2.5 gal.) 2871721 Premium Gold Synthetic 2-Cycle Engine Oil (qt.) 2871722 Premium Gold Synthetic 2-Cycle Engine Oil (gal.)

  • Page 118: Troubleshooting

    TROUBLESHOOTING Engine Troubleshooting Unless you have experience and training in two-cycle engine repair, see your dealer if technical problems arise. Problem Probable Cause Solution Erratic engine oper- Drive clutch binding • SEE YOUR DEALER. ating RPM during Driven clutch mal- •...
  • Page 119 TROUBLESHOOTING Engine Troubleshooting Problem Probable Cause Solution Noise in drive sys- Broken drive clutch • SEE YOUR DEALER. components Bearing failure/ • SEE YOUR DEALER. chaincase, jackshaft, or front drive shaft Drive belt surface • Inspect and replace as needed. flat spots Drive chain loose •...
  • Page 120 TROUBLESHOOTING Engine Troubleshooting Problem Probable Cause Solution Engine turns but fails Faulty ignition • Install new spark plug(s). If engine to start still fails to start, check for spark. If there's no spark, SEE YOUR DEALER. No fuel to engine •...
  • Page 121 TROUBLESHOOTING IQ Suspension Troubleshooting Problem Solution Rear suspension bot- • Adjust torsion spring preload to achieve proper static sag toms too easily (see page 44). • Change torsion spring to stiffer optional spring (see your dealer). • Revalve rear track shock (see your dealer). Rides too stiff in rear •...
  • Page 122 TROUBLESHOOTING Drive Belt Troubleshooting Belt Wear/Burn Diagnosis Causes Solutions Driving at low RPM • Drive at higher RPMs. Gear the machine down. Check belt deflection. Insufficient warm-up • Warm the engine at least five minutes. Take the drive belt off the machine in extremely cold weather and warm it up.

  • Page 123: Warranty

    Your dealer receives frequent updates on changes, modifications and tips on snowmobile maintenance, which may supersede information con- tained in this manual. Your dealer is also familiar with Polaris policies and pro- cedures and will be happy to assist you.
  • Page 124 Polaris warranty will provide all dealerships with a monthly updated list of all stolen units to further monitor thefts. Polaris warranty will aid in notifying the proper owner when a unit is recovered.
  • Page 125 WARRANTY Limited Warranty Polaris Sales Inc., 2100 Highway 55, Medina, MN 55340, provides a ONE YEAR LIM- ITED WARRANTY on all components of the Polaris snowmobile against defects in material or workmanship. This warranty covers the parts and labor charges for repair or replacement of defective parts that are covered by this warranty.
  • Page 126 How to Obtain Warranty Service If your snowmobile requires warranty service, you must take it to a Polaris dealer autho- rized to repair Polaris snowmobiles. When requesting warranty service you must present your copy of the Warranty Registration form to the dealer. (The cost of transportation to and from the dealer is YOUR responsibility).
  • Page 127 In order to qualify for warranty, the product must have been properly set up and tested by a Polaris Dealer (if applicable). Failure of any dealer to perform the required vehicle Pre-Delivery Inspection, perform all applicable service bulletins and have the consumer sign the PDI form prior to delivery may void the warranty.
  • Page 128 • Failures caused due to improper adjustments. • Failure due to unauthorized service. • Failures due to lack of service as required in the owner's manual or Polaris updates. This includes off-season storage as listed in the owner's manual. • Failure due to use of unauthorized parts or modifications.
  • Page 129 If Purchased From A Private Party: If you purchase a Polaris product from a private citizen outside of the country in which the vehicle was originally purchased, all warranty coverage will be denied.
  • Page 130 Protection Agency regulations applicable to snowmobile emissions under 40 CFR1051, 1065 and 1068 at the time of sale to the ultimate purchaser. Polaris warrants that the engine is free from defects in materials and workmanship that may keep it from meeting these regulations.
  • Page 131 Any qualified repair shop or qualified person may maintain, replace, or repair the emission control devices or systems on your snowmobile. Polaris recom- mends that you contact an authorized Polaris dealer to perform any service that may be necessary.

  • Page 132: Maintenance Log

    MAINTENANCE LOG Present this section of your manual to your dealer each time your snow- mobile is serviced. This will provide you and future owners with an accurate log of maintenance and services performed on the snowmobile. DATE MILES TECHNICIAN SERVICE PERFORMED / COMMENTS (KM) 150 mi.
  • Page 133 MAINTENANCE LOG DATE MILES TECHNICIAN SERVICE PERFORMED / COMMENTS (KM)
  • Page 134 MAINTENANCE LOG DATE MILES TECHNICIAN SERVICE PERFORMED / COMMENTS (KM)

  • Page 135: Index

    INDEX Accessories ....51 Drive Belt Adjustment... 100 Adjustable Headlights ... 27 Drive Belt Deflection.
  • Page 136 INDEX Ice and Snow Build-up ... 14 Rail Slide Wear....110 IFS......39 Rear Rear Scissor Stop .
  • Page 137 INDEX Suspension Coupling, IQ ..47 Track Maintenance ..102-106 Suspension Inspection, Pre-Ride . . 110 Track Safety..... 8 Suspension Maintenance .

This manual is also suitable for:

2007 dragon

Table of Contents