Casio 3017 Operation Manual page 5

Operation Guide 3017
Setting the Time and Date
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the time and date
1. In the Timekeeping Mode, hold down A until the city
City code
code starts to flash, which indicates the setting screen.
2. Press C to change the flashing contents in the
sequence shown below to select other settings.
12/24-Hour
City Code DST
Format
Timekeeping Mode Screens
Power
(Day of the Week/Date or Time/Date)
Saving
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Screen: To do this:
Change the city code
Cycle between auto DST (
Time ( ), and Daylight Saving Time
( )
Toggle between 12-hour ( 12H
( 24H ) timekeeping
Reset the seconds to
Toggle the illumination duration setting
between 1.5 seconds ( ) and 2.5 seconds
( )
Change the hour, minutes, or year
Change the month or day
Toggle Power Saving on (
( )
Specify Day of the Week/Date or Time/Date
(indicated by ---) for the Timekeeping
Mode screens.
• See "City Code Table" for a complete list of available city codes.
• Auto DST (
) can be selected only while LIS, LON, BCN, MAD, PAR, MIL,
ROM, BER, STO, or ATH is selected as the Home City code. For more
information, see "Daylight Saving Time (DST)" below.
• For information about settings other than the time and date, see the following.
Illumination duration: Illumination
Power Saving: Power Saving Function
Timekeeping Mode Screens (Day of the Week/Date or Time/Date)
Press A to exit the setting screen.
4.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signal transmitted from Mainflingen and Rugby includes both
Standard Time and DST data. When the Auto DST setting is turned on, the watch
switches between Standard Time and DST (summer time) automatically in
accordance with the received time signal.
• The default DST setting is Auto DST (
MAD, PAR, MIL, ROM, BER, STO, or ATH as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it
probably is best to switch between Standard Time and Daylight Saving Time
(summer time) manually.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
Auto DST ( ) DST off (
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
Timekeeping Mode Screens (Day of the Week/Date or Time/Date)
Use the procedure below to select either Day of the Week/Date or the Time/Date for
the Timekeeping Mode screens.
• In the Timekeeping Mode, you can press A to toggle the display contents as shown
below.
Day of the Week/Date
PM indicator Day of week
Press A.
Hour : Minutes
Seconds
Time/Date
Hour : Minutes
Press A.
Seconds
Timekeeping Screen
Seconds Hour Minutes
Day
Month Year
Do this:
Use D (east) and B
(west).
Press D.
), Standard
Press D.
) and 24-hour
Press D.
Press B.
Use D (+) and B (–).
) and off
Press D.
Press D.
) whenever you select LIS, LON, BCN,
) DST on ( )
Month – Day
Day of week
Month – Day
Calendar Screen
* If you leave the calendar screen displayed for two or three minutes without
performing any operation, the watch will automatically return to the timekeeping
screen.
To specify the Timekeeping Mode screens
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C 10 times so the current Timekeeping Mode screens setting is flashing.
• Day of the Week/Date are selected if the setting screen shows the current date
flashing.
• Time/Date are selected if the setting screen shows "---" flashing in place of
the current date.
3. Press D to toggle the Timekeeping Mode screens between Day of the Week/Date
(current date displayed) and Time/Date ( "---" displayed).
4. Press A to exit the setting screen.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
The button operation tone sounds any time you press one
of the watch's buttons. You can turn the button operation
tone on or off as desired.
• Even if you turn off the button operation tone, the alarm,
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
MUTE indicator display), hold down C to toggle the button operation tone
on (MUTE not displayed) and off (MUTE displayed).
• Since the C button is also the mode change button, holding it down to turn the
button operation tone on or off also causes the watch's current mode to change.
• The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Power Saving Function
When turned on, the Power Saving function enters a sleep
state automatically whenever the watch is left in an area
where it is dark for a certain period. The table below
shows how watch functions are affected by the Power
Saving function.
Power saving
indicator
Elapsed Time Display
in Dark
60 to 70 minutes Blank, with Power Saving
indicator (PS) flashing
6 or 7 days Blank, with Power Saving
indicator (PS) not flashing
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 10:59 PM. If the
watch is already in the sleep state when 6:00 AM arrives, however, it will remain in
the sleep state.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C nine times until the Power Saving on/off
screen appears.
3. Press D to toggle Power Saving on (
( ).
4. Press A to exit the setting screen.
• The Power Saving indicator (PS) is on the display in all
On/Off status
modes while Power Saving is turned on.
Auto Return Features
• If you leave the watch in the Alarm Mode for two or three minutes without performing
any operation, it returns to the Timekeeping Mode automatically.
• If you leave the watch with a flashing setting on the display for two or three minutes
without performing any operation, the watch exits the setting screen automatically.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data. In most cases, holding down these buttons during a scroll operation
scrolls through the data at high speed.
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
Radio-controlled Timekeeping Precautions
• Strong electrostatic charge can result in the wrong time being set.
• The time calibration signal is bounced off the ionosphere. Because of this, such
factors as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
Operation
All functions enabled, except
for the display
Beeper tone, backlight, and
display are disabled.
) and off
5