Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele KM 2356
Summary of Contents for Miele KM 2356
- Page 1 Operating and installation instructions Gas hobs KM 2356 KM 2357 en - GB To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time.
- Page 2 Per questo se si vuole usare l’apparecchio in un paese diverso rivolgersi al servizio di assistenza tecnica Miele del paese in cui si intende usarlo.
- Page 3 Gas-heated appliances Safety precautions to take if you smell gas ß Turn off the gas emergency control valve immediately. This is usually located near the gas meter. ß Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. ß...
-
Page 4: Table Of Contents
KM 2356 ........ - Page 5 Contents KM 2357 ............39 Building-in dimensions .
-
Page 6: Guide To The Appliance
Guide to the appliance a Small burner Controls: b Large burner g Front left c Wok burner h Back left d Medium burner i Middle e Medium burner j Back right f Pan support (in three sections) k Front right... - Page 7 Guide to the appliance Burners Wok burner Small, medium and large burners a Burner cap b Burner head c Ignition safety device d Ignitor a Outer burner cap e Burner base b Inner burner cap c Burner head d Burner base e Ignition safety device f Ignitor...
-
Page 8: Accessories Supplied
Guide to the appliance Accessories supplied The accessories supplied with your appliance as well as a range of optional ones are available to order from Miele (see "Optional accessories"). Wok ring The Wok ring supplied with your appliance can be used in instances where extra stability is required. -
Page 9: Warning And Safety Instructions
It is intended for domestic use only to cook food and keep it warm. Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation. The gas hob is not intended for outdoor use. - Page 10 Warning and Safety instructions Safety with children This appliance is not a toy! To prevent the risk of injury, do not allow children to play with it or use the controls. Please supervise children whilst you are using the appliance. Children under 8 years of age must be kept away from the hob unless they are constantly supervised.
- Page 11 It is most important that this basic safety requirement is observed and tested regularly, and where there is any doubt, the household wiring system should be inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
- Page 12 If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Spare Parts Department. Do not connect the appliance to the mains electricity supply by a multi-socket adapter or an extension lead.
- Page 13 Warning and Safety instructions In areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.
- Page 14 If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the hob. Miele cannot be held liable for this type of damage.
- Page 15 Warning and Safety instructions Remove splashes of fat and other food debris from the surface as soon as possible. These are a fire hazard. Replace the pan supports carefully to avoid scratching the surface of the hob. Using a gas hob results in the build-up of heat, moisture and combustion products in the room in which it is installed.
- Page 16 If the appliance has not been used for a long period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested for safety. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
-
Page 17: Caring For The Environment
Caring for the environment Disposal of the packing Disposal of your old appliance material Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment. -
Page 18: Before Using For The First Time
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate" section of this booklet. Cleaning for the first time ^ Remove any protective foil. ^ Clean all removable parts of the burners with a solution of warm water and a little washing-up liquid applied with a soft sponge. -
Page 19: Operation
Operation Rapid ignition system The appliance has a rapid ignition system with the following features: – Rapid ignition without pressing and holding the control dial – Automatic reignition If the flame is extinguished by a draught, etc. the burner is automatically reignited. -
Page 20: Switching On
Operation Switching on When using the gas hob an extractor hood or a ventilation facility must be used. ^ The control for the burner required must be pressed in and turned anti-clockwise to the largest flame symbol to switch on. The ignitor will make a clicking sound and ignite the gas. -
Page 21: Regulating The Flame
Operation Regulating the flame Regulate the flame so that it does not spread out beyond the sides of the pan. As the outer part of the flame is much hotter than the centre, the tips of the flames should stay beneath the pan base. -
Page 22: Pans
Pans Burner Min. pan base diameter in cm Small Medium Large Max. diameter at top of pan in cm Without With Combi insert Small Medium Large – Refer to the chart above and ensure that the pan diameter falls within the minimum and maximum diameters given for the burner you are using. -
Page 23: Wok Ring
Pans Wok ring The Wok ring supplied with your appliance can be used in instances where extra stability is required. It is particularly suitable for Woks with a rounded base. Make sure that the wok ring is located securely in its correct position. -
Page 24: Energy Saving Tips
Energy saving tips – Use a pan lid whenever possible to minimise heat loss. – Cook with as little water as possible. – Cooking times are greatly reduced when using a pressure cooker. – Turn the flame down promptly to a lower setting when the pan has come to the boil. -
Page 25: Safety Features
Safety features Thermo-electric ignition safety device This appliance is has a thermo-electric ignition safety device. If the flame goes out, for example if food has boiled over or if there is a sudden draught, and automatic re-ignition has been unsuccessful, the supply of gas to the burner will be cut off preventing any further escape of gas. -
Page 26: Cleaning And Care
Cleaning and care Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. – The appliance should be cleaned after each use. Allow the appliance to cool down to a safe temperature before cleaning. - Page 27 Remove any soiling which applied with a soft sponge. comes into contact with the If necessary, you could use Miele ceramic and printed flame symbols stainless steel hob cleaner (see "Optional straight away. Soiling, accessories") and the scouring pad on the...
- Page 28 Cleaning and care To assemble the small, medium and large burners ^ Place the burner head b on to the burner base e so that the ignition safety device d and the ignitor c extend through their respective holes in the burner head. The burner head must click into place correctly.
- Page 29 Cleaning and care To assemble the wok burner ^ Place burner head c onto burner base d so that the ignition safety device e and the ignitor f extend through their respective holes in the burner head. The burner head must click into place correctly.
-
Page 30: Problem Solving Guide
Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department saving you both time and money. The following guide may help you to find the reason for a fault, and to correct it. - Page 31 The ignitor on the burner Check whether the mains If it has, contact a qualified electrician or does not spark. fuse has tripped. Miele Service. - Food residues between Remove any soiling. Please see "Cleaning the ignitor and the burner and care" for details.
-
Page 32: Optional Accessories
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your appliance. These products can be ordered online at: or from Miele (see back cover for contact details) Cleaning products Ceramic and stainless steel hob cleaner... -
Page 33: Safety Instructions For Installation
Safety instructions for installation Do not use any sealant except Fit the wall units and extractor hood where expressly instructed to do so. before fitting the appliance to avoid The seal underneath the appliance damaging the surface. provides a sufficient seal for the worktop. - Page 34 Safety instructions for installation Safety distance above the hob When two or more appliances are installed together below a cooker hood, e.g. a gas hob and an induction hob combiset, which have different safety distances given in the installation instructions, you should select the greater distance of the two.
- Page 35 Safety instructions for installation Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall on one side (right or left) (see illustrations).
-
Page 36: Building-In Dimensions
KM 2356 Building-in dimensions a Front b Casing depth c Gas connection R 1/2 - ISO 7-1 (DIN 10226) d Mains connection box with mains connection cable, L = 2,000mm e Electronics housing Max. building-in depth 101 mm... - Page 37 KM 2356 Installation ^ Make the worktop cut-out as shown in "Building-in dimensions". Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Seal the cut surfaces on wood/laminated worktops with a suitable heat-resistant sealant to avoid swelling caused by moisture.
-
Page 38: Tiled Worktop
KM 2356 Seal between appliance and Tiled worktop worktop Grout lines a and the hatched area underneath the hob frame must be smooth and even. If they are not the The sealing strip under the edge of the hob will not sit flush with the worktop... -
Page 39: Building-In Dimensions
KM 2357 Building-in dimensions a Front Please take careful note of the b Casing depth detailed diagrams for the cut-out dimensions in granite and marble c Gas connection worktops. R 1/2 - ISO 7-1 (DIN EN 10226) d Electrical connection cable e Electronics housing Max. - Page 40 KM 2357 Flush fit gas hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit hob.
-
Page 41: Installation
KM 2357 ^ Make the worktop cut-out as shown Installation in "Building-in dimensions". Granite and marble worktops Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Feed the connection cable down through the cut-out. ^ Centre the hob b in the cut-out. ^ Connect the hob to the mains (see "Electrical connection"). - Page 42 KM 2357 ^ Make the worktop cut-out as shown Solid wood and tiled worktops in "Building-in dimensions". Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Fix the wooden frame d 2 mm below the top edge of the worktop (see diagram).
- Page 43 Building into a stainless steel worktop This appliance can be welded into a stainless steel worktop. It is essential that after being welded, it is still recognisable as a Miele appliance. Welding must be carried out by a trained, Miele-approved person.
-
Page 44: Securing The Appliance
Securing the appliance After installation Secure the appliance as shown, using the fixings supplied. Check that all the burners are operating correctly. 20 mm worktop The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. -
Page 45: Electrical Connection
Electrical connection Connection should be made via a All electrical work should be carried suitable isolator or a double pole fused out by a suitably qualified and spur connection unit which complies competent person, in strict with national and local safety accordance with current local and regulations and the on/off switch should national safety regulations (BS 7671... - Page 46 If the connection cable is damaged, it must be replaced by a suitably qualified electrician with a special connection cable of type H 05 V V-F (pvc insulated), available from the Miele Service Department. The manufacturer cannot be held liable for damage which is the direct or indirect result of incorrect installation or connection.
-
Page 47: Gas Connection
Please contact your dealer or the Miele Spare Parts Department for the Check with your local gas supplier appropriate conversion jets if about the type of gas and its necessary. - Page 48 Gas connection Connection Using a 90° angle The gas connection must be installed so that connection can be made either from inside or outside the kitchen unit, and the isolating valve must be easily accessible and visible (by opening one of the kitchen doors, if necessary).
-
Page 49: Burner Ratings
Burner ratings Nominal rating Burner Gas type High setting Low setting Small burner Natural gas H 1.00 0.27 Liquid gas 1.00 0.73 0.21 Medium burner Natural gas H 1.70 0.30 Liquid gas 1.70 0.30 Large burner Natural gas H 2.70 0,51 Liquid gas 2.60... -
Page 50: Conversion To Another Type Of Gas
Conversion to another type of gas Connection to the gas supply, or conversion from one type of gas to another, should only be undertaken by an approved and registered gas installer in strict accordance with local and national safety and building regulations (e.g. -
Page 51: To Change The Main Jets
Conversion to another type of gas Changing the jets To change the main jets Disconnect the gas hob from the Small, medium and large burners mains electricity supply. Turn off the gas supply. ^ Remove the pan support, burner cap a and burner head b. - Page 52 Conversion to another type of gas Wok burner ^ Remove burner cap ab and burner head c. ^ Using an M7 socket spanner, unscrew the main jet d ^ Fit the correct jets securely (see jet table). ^ Finally, secure the jets against inadvertent loosening with sealing wax.
-
Page 53: To Change The Small Jets
Conversion to another type of gas To change the small jets Wok burner To change the small jets, the burner securing screws must first be loosened and the upper section of the appliance removed. ^ Pull the control knobs off. ^ Remove the burner parts. -
Page 54: Function Test
Conversion to another type of gas Function test Check all gas fittings for leaks. ^ Reassemble the appliance. ^ Check the burner flame by operating the burner. The flame must not go out on the lowest setting, or when the control is turned quickly from a high to a low setting. -
Page 55: After Sales Service, Data Plate, Guarantee
Please note that telephone calls may be monitored and recorded to improve our service. When contacting Miele, please quote the model and serial number of your appliance. These are given on the data plate. N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions. - Page 56 Alteration rights reserved / 2112 M.-Nr. 09 370 470 / 01...