Related Manuals for Seagate ST8000AS0002
Summary of Contents for Seagate ST8000AS0002
- Page 1 Product Manual Seagate Archive HDD ® Standard models Self-Encryption models ST8000AS0002 ST8000AS0012 ST6000AS0002 ST6000AS0012 Gen 2 100757960 Rev. B November 2014...
- Page 2 United States and/or other countries. Archive HDD and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trade- marks or registered trademarks are the property of their respective owners.
-
Page 3: Table Of Contents
Seagate® Technology Support Services ........ - Page 4 S.M.A.R.T. commands ..........33 Seagate Archive HDD Product Manual, Rev. B...
- Page 5 Mounting dimensions............22 Seagate Archive HDD Product Manual, Rev. B...
-
Page 6: Seagate Technology Support Services
Authorized Service Centers For information regarding Warranty Support, visit: http://www.seagate.com/support/warranty-and-replacements/ For information regarding data recovery services, visit: http://www.seagate.com/services-software/data-recovery-services/ For Seagate OEM and Distribution partner portal, visit: http://www.seagate.com/partners For Seagate reseller portal, visit: http://www.seagate.com/partners/my-spp-dashboard/ Seagate Archive HDD Product Manual, Rev. B... -
Page 7: Introduction
• Native Command Queuing with command ordering to increase performance in demanding applications. • Full-track multiple-sector transfer capability without local processor intervention. • Seagate AcuTrac™ servo technology delivers dependable performance, even with hard drive track widths of only 75 nanometers. -
Page 8: About The Sata Interface
SATA ports are represented to host software as a Device 0 (master) and Device 1 Note (slave) accessed at the same set of host bus addresses. A host adapter that emulates a master/slave environment manages two sets of shadow registers. This is not a typical SATA environment. Seagate Archive HDD Product Manual, Rev. B... -
Page 9: Drive Specifications
Temperature gradient 30°C per hour max (nonoperating) 5% to 90% (operating) Relative humidity 5% to 95% (nonoperating) Relative humidity gradient (max) 30% per hour 30°C max (operating) Wet bulb temperature (max) 37.7°C max (nonoperating) Seagate Archive HDD Product Manual, Rev. B... - Page 10 ** One GB equals one billion bytes and 1TB equals one trillion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. *** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Seagate Archive HDD Product Manual, Rev. B...
-
Page 11: Formatted Capacity
1950 Track density (Ktracks/inch avg) Areal density (Gb/in Internal data transfer rate (Mb/s max) 1900 Maximum sustained data transfer rate, OD read (MB/s) Average data rate, read/write (MB/s) I/O data-transfer rate (MB/s max) Seagate Archive HDD Product Manual, Rev. B... -
Page 12: Physical Characteristics
(in seconds) 25 (max) Ready to spindle stop 15 (typical) (in seconds) 20 (max) Time-to-ready may be longer than normal if the drive power is removed without going through normal OS powerdown procedures. Seagate Archive HDD Product Manual, Rev. B... -
Page 13: Power Specifications
Typical DC 0.37 0.40 Maximum DC 0.37 0.41 * During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. Seagate Archive HDD Product Manual, Rev. B... -
Page 14: Conducted Noise
10MHz. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. Note 2.8.3 Voltage tolerance Voltage tolerance (including noise): • 5V = ±5% • 12V = ±10% Seagate Archive HDD Product Manual, Rev. B... -
Page 15: Extended Power Conditions - Powerchoicetm
• Default enabled state, and timer value • Saved enabled state, and timer value • Current enabled state, and timer value S.M.A.R.T. Read Data Reports • Attribute 192 - Emergency Retract Count • Attribute 193 - Load/Unload Cycle Count Seagate Archive HDD Product Manual, Rev. B... - Page 16 Enable EPC Feature Set Disable EPC Feature Set PowerChoice Supported Extended Power Condition Identifiers Power Condition Identifiers Power Condition Name Standby_z 01 - 80 Reserved Idle_a Idle_b Idle_c 84 - FE Reserved All EPC Power Conditions Seagate Archive HDD Product Manual, Rev. B...
-
Page 17: Environmental Specifications
The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 250 Gs based on a non-repetitive half-sine shock pulse of 2ms duration. Seagate Archive HDD Product Manual, Rev. B... -
Page 18: Operating Vibration
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO 389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 19: Electromagnetic Immunity
EN 55022, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. -
Page 20: Fcc Verification
As a subassembly, no Federal Communications Commission verification or certification of the device is required. Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursuant to Subpart J, Part 15 of the FCC rules. -
Page 21: Environmental Protection
The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. -
Page 22: Configuring And Mounting The Drive
For installations which require cables, users can connect the drive as illustrated in Figure 2 Figure 2 Attaching SATA cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation. Archive HDD drives support latching SATA connectors. Seagate Archive HDD Product Manual, Rev. B... -
Page 23: Drive Mounting
• The screws should be inserted no more than 0.150 inch (3.81mm) into the bottom or side mounting holes. • Do not overtighten the mounting screws (maximum torque: 6 inch-lb). Figure 3 Mounting dimensions Seagate Archive HDD Product Manual, Rev. B... -
Page 24: About (Sed) Self-Encrypting Drives
In case of conflict between this document and any referenced document, this document takes precedence. The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the computer, storage and digital communications industry. Seagate's SED models comply with the standards published by the TCG. -
Page 25: Random Number Generator (Rng)
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also only accepts download files which have been cryptographically signed by the appropriate Seagate Design Center. Three conditions must be met before the drive will allow the download operation: 1. -
Page 26: Sata Interface
5V power, pre-charge, 2nd mate Power 5V power 5V power Ground 2nd mate Ground or LED signal If grounded, drive does not use deferred spin Ground 1st mate. 12V power, pre-charge, 2nd mate 12V power 12V power Seagate Archive HDD Product Manual, Rev. B... -
Page 27: Supported Ata Commands
Read DMA Extended Read DMA Without Retries Read Log Ext Read Multiple Read Multiple Extended Read Native Max Address Read Native Max Address Extended Read Sectors Read Sectors Extended Read Sectors Without Retries Seagate Archive HDD Product Manual, Rev. B... - Page 28 S.M.A.R.T. Save Attribute Values / D3 S.M.A.R.T. Write Log Sector / D6 Standby Standby Immediate Write Buffer Write DMA Write DMA Extended Write DMA FUA Extended Write DMA Without Retries Write Log Extended Write Multiple Seagate Archive HDD Product Manual, Rev. B...
-
Page 29: Identify Device Command
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write 8010 multiple (16) Reserved 0000 Standard Standby timer, IORDY supported and may be disabled 2F00 ATA-reserved 0000 PIO data-transfer cycle timing mode 0200 Seagate Archive HDD Product Manual, Rev. B... - Page 30 Command sets enabled 30xx Command sets enabled BE09 Command sets enable extension 4163 Ultra DMA support and current mode (see note following this table) xx7F Security erase time 0039 Enhanced security erase time 0039 Seagate Archive HDD Product Manual, Rev. B...
- Page 31 Media Card Pass Through Command feature set is supported. Streaming feature set is supported. GPL feature set is supported. WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported. WRITE DMA QUEUED FUA EXT command is supported. Seagate Archive HDD Product Manual, Rev. B...
- Page 32 Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Seagate Archive HDD Product Manual, Rev. B...
-
Page 33: Set Features Command
Disable use of SATA features Enable read look-ahead (read cache) feature (default) Report full capacity available At power-on, or after a hardware or software reset, the Note default values of the features are as indicated above. Seagate Archive HDD Product Manual, Rev. B... -
Page 34: Commands
S.M.A.R.T. Enable Operations S.M.A.R.T. Disable Operations S.M.A.R.T. Return Status If an appropriate code is not written to the Features Register, the Note command is aborted and 0x 04 (abort) is written to the Error register. Seagate Archive HDD Product Manual, Rev. B... - Page 35 ASIA/PACIFIC Seagate Singapore International Headquarters Pte. Ltd. 7000 Ang Mo Kio Avenue 5, Singapore 569877, 65-6485-3888 EUROPE, MIDDLE EAST AND AFRICA Seagate Technology SAS 16-18 rue du Dôme, 92100 Boulogne-Billancourt, France, 33 1-4186 10 00 Publication Number: 100757960, Rev. B...