Table of Contents
Advertisement
Quick Links
E
IMAGE
Operator's
26B
Manual
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your ALTO machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well. You must have training in the operation of this machine before using it. If your operator(s) cannot
read English, have this manual explained fully before attempting to operate this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes
de tratar el manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 70249A 10/01
CLARKE TECHNOLOGY
Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Alto IMAGE 26B
Summary of Contents for Alto IMAGE 26B
- Page 1 This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
-
Page 2: Table Of Contents
36 Volt Battery Charger ................... 31 Battery Cart Assembly .................... 32 Battery Cart Instructions ..................33 Available Accessories ..................... 34 Wiring Schematic ....................35 Connection Diagram ....................36 Flow Diagram ......................37 Page -2- Clarke Technology Operator's Manual IMAGE 26B... -
Page 3: Operator Safety Instructions
Machines can topple over if guided over the edges of stairs or loading docks and cause injury or damage. Stop and leave this machine only on a level surface. When you stop the machine, put all switches into their "OFF" position. Clarke Technology Operator's Manual IMAGE 26B Page -3-... - Page 4 Do not use this machine as a step or furniture. Do not ride on this machine. CAUTION: Carpet damage can occur if carpet has not adequately dried before traffic resumes. Stay off the carpet until it is dry. Page -4- Clarke Technology Operator's Manual IMAGE 26B...
-
Page 5: Introduction And Machine Specifications
INTRODUCTION AND MACHINE SPECIFICATIONS The IMAGE 26B is a one-piece, self-propelled carpet extractor designed for cleaning carpet. The machine applies cleaning solution to the carpet and then removes the dirty solution and soil with a recovery tool. Features: u Easy to Operate u Interex cleaning system. -
Page 6: Transporting The Machine
The machine is heavy. Make sure you use two able persons to assist the machine down the ramp. 6. Assisting the machine down the ramp, position yourself to maintain a slow downward speed. Page -6- Clarke Technology Operator's Manual IMAGE 26B... -
Page 7: Machine Controls
Figure 3 hose. Pump Switch (See figure 3,B) The pump switch allows the pump to be turned off when solution application is not required. Clarke Technology Operator's Manual IMAGE 26B Page -7-... - Page 8 The accessory hose connector is used to hook-up optional auxiliary floor tools and to redirect the solution flow. Use hose coupler (P.N. 30108A) to connect accessory hose to recovery shoe hose. Figure 5 Figure 6 Page -8- Clarke Technology Operator's Manual IMAGE 26B...
- Page 9 (D) . To return battery tray to operating position, release lever and slide tray back into machine until lever engages in frame. Raise and latch bridge. Close front. Figure 8 Clarke Technology Operator's Manual IMAGE 26B Page -9-...
-
Page 10: How To Prepare The Machine For Operation
HOW TO PREPARE THE MACHINE FOR OPERATION The Image 26B uses three 12-Volt batteries. The batteries are located on a battery tray that can be accessed by opening the front cover and lowering the front bridge. To install the batteries, follow this procedure: 1. - Page 11 DC connector on the charger could result in an explosion. Always disconnect the AC plug from the wall recep- tacle before connecting or disconnecting the DC connector on the charger. Clarke Technology Operator's Manual IMAGE 26B Page -11-...
- Page 12 3. Add a minimum of five (5) gallons of clean water to the on the carpet when not in solution tank. use. NOTE: Do not use water that is hotter than 140°F. Page -12- Clarke Technology Operator's Manual IMAGE 26B...
- Page 13 NOTE: Verify battery condition under use. If batteries are discharged, pump and brush motor will not function. Vacuum and traverse contiue to allow water recovery and ability to return to charging station. Clarke Technology Operator's Manual IMAGE 26B Page -13-...
-
Page 14: Machine Operating Instructions
This machine is not equipped with a parking brake. Never leave the machine unattended. For added safety, always place a chock in front of and behind the drive wheel. Page -14- Clarke Technology Operator's Manual IMAGE 26B... - Page 15 3. To speed drying time of the carpet try a Clarke Technology Direct Air carpet dryer. Clarke Technology Operator's Manual IMAGE 26B Page -15-...
- Page 16 2. Make sure that the machine and the pump are completely dry. 3. Make sure the machine is at room temperature before using it. Electrical NOTE: For electrical repairs, return this machine to a Clarke Technology authorized repair center. Page -16- Clarke Technology Operator's Manual IMAGE 26B...
-
Page 17: Maintenance Instructions
Remove the spacer and brush from the brush housing. Place brush onto the shaft. Slide brush in and rotate until the pins catch. Slide spacer onto shaft. Swing door down and slide onto shaft. Replace clamping knob. Clarke Technology Operator's Manual IMAGE 26B Page -17-... - Page 18 3. Pull nozzle assembly out to side of machine. 4. Firmly push nozzle in and turn 1/4 turn. 5. Pull nozzle out. 6. Clean and replace into nozzle assembly. 7. Replace nozzle assembly in brush housing. Page -18- Clarke Technology Operator's Manual IMAGE 26B...
-
Page 19: Section Ii Parts And Service
IMAGE 26B Section II Parts and Service Manual (70249A) Clarke Technology Operator's Manual IMAGE 26B Page -19-... -
Page 20: How To Correct Problems In The Machine
Loose motor connection. Contact an authorized ClarkeTechnology service person. Vac motor switch defective. Contact an authorized Clarke Technology service person. Brush does not run or runs Batteries are too low. Charge Batteries. intermittently. Page -20- Clarke Technology Operator's Manual IMAGE 26B... -
Page 21: Recovery Tank And Hose Assembly
Solution/Recovery Bracket 85728A Screw, ¼-20 x 4 872010 Clamp, Hose 30448A Hose, Vac Exhaust 51863A Cuff 59877A Washer, O-Ring 82100A Nut, Lock 47905A Terminal 962943 Screw, 8-18 x ½ PH 980646 Washer Clarke Technology Operator's Manual IMAGE 26B Page -21-... -
Page 22: Handle Assembly
Circuit Breaker, 25A (vac/tr mtr) 3 81102A Nut, Nylock 41161a Control Motor, Quad 30033A Gasket, Handle 40190A Harness, Wiring 30032A Gasket, Control Panel 962430 Screw, ¼-20 x ½ Page 23 (see item #35) Page -22- Clarke Technology Operator's Manual IMAGE 26B... -
Page 23: Rear Panel Assembly
52419A Tip, Chemical Metering 60467A Arm, Brush Lift 962968 Screw 60052A Retainer, Drain Valve 81110A 438360 Spring, Adjustor 722021 Hose Clamp 980692 Washer, Flat 77366A Label 65447A Lift, Recovery Tool 77367A Label Clarke Technology Operator's Manual IMAGE 26B Page -23-... -
Page 24: Solution Tank Assembly
81110A Nut, 10-24 ESNA 41162A Cable, Asm. Console 962666 Screw, 10-24 x Pan SS 962212 Screw 38820A Tank, Solution 920056 65506A Latch, Bridge 30463A Hose 980646 Washer, ¼ Flat 60218A Plug, Drain Page -24- Clarke Technology Operator's Manual IMAGE 26B... -
Page 25: Solution Delivery System
Reducer, ¼ to 694112 Hose 10229A Injector Asm. (incl. 5, 10, 11, 12, 45950A Pump 14 & 19) 52418A Head Replacement, Pump 55167A Hosebarb 35148A Hose 732870 Elbow 53639A Elbow 722021 Hose Clamp Clarke Technology Operator's Manual IMAGE 26B Page -25-... -
Page 26: Frame Assembly
Washer, Flat ¼ 53087A Strap, Static 55013A Hinge 81104A Nut, ¼-20 SS 61539A Bridge 980652 Washer, Lock 69206A Wheels 47905A Terminal 50008B Transaxle 50250B Motor, Transaxle 50251A Brush Motor 52660A Coupler, Transaxle Page -26- Clarke Technology Operator's Manual IMAGE 26B... -
Page 27: Battery Tray
Screw 980651 Washer 41217A Cable, 16" 920160 40532A Cable Asm., Battery 608210 Spacer 40506A Charger, 36VDC NOTE: u indicates that a change has been made since the last publication of this manual. Clarke Technology Operator's Manual IMAGE 26B Page -27-... -
Page 28: Recovery Tool Assembly
67619A Shoe, Recovery Tool 85391A Screw, ¼-20 68808A Weight, Recovery Tool 30517A Bushing 85615A Screw, -18 x 1¼ 51320A Nozzle, Rinse 27201A Shoe, Recovery 61541A Bracket, Recovery Lift 980652 Lockwasher *Optional Accessory Page -28- Clarke Technology Operator's Manual IMAGE 26B... -
Page 29: Brush Assembly
Spacer, Brush Door 920208 Nut, Hex ¼-20 81109A Nut, 8-32 ESNA 980614 Washer, Lock 55518A Knob, Clamping 10220A Bar Asm., Pre-Spray (incl. 4, 5, 60089A Door, Brush End 6, 7 & 8) Clarke Technology Operator's Manual IMAGE 26B Page -29-... -
Page 30: Vac Motor Assembly
Carbon Brushes 658201 Spacer 51914A Clamp 53908A Fan - Stationary 50618A Bracket 658506 Shell 53100A Disc 53995A Fan, Air Seal 902679 Bearing - Ball 53996A Fan, Stationary 902648 Bearing - ball, radial Page -30- Clarke Technology Operator's Manual IMAGE 26B... -
Page 31: Volt Battery Charger
837525 Strain Relief, D.C. Cord 747553 747553 747553 D.C. Cord Assembly 51973A 51973A 51973A A.C. Cord Assembly 51974A 908947 908947 D.C. Plug 911185 911185 911185 D.C. Plug Lock Key 795020 795020 795020 Clarke Technology Operator's Manual IMAGE 26B Page -31-... -
Page 32: Battery Cart Assembly 1/01
980652 Washer, Lock 5/16 170854 nut, 5/16-18 962157 Screw, 5/16-18 x 1¼ 87607A Washer, Nylon 920110 Nut, 5/16-18 ESNA 85704A Screw, 3/8-16 x 2¼ 980645 Washer, Flat 3/8 920342 Nut, 3.8-16 ESNA Page -32- Clarke Technology Operator's Manual IMAGE 26B... -
Page 33: Battery Cart Instructions
(F). 11. Step on foot lever on battery cart to disengage cart from bridge (G). 12. Replace battery pack by doing the steps above in reverse order. Clarke Technology Operator's Manual IMAGE 26B Page -33-... -
Page 34: Available Accessories 1/01
55183A Hide-A-Hose 20' Pg.30 10010A Battery Cart 10014A Quick Change Battery Kit 55173A 4" Tool & Hose Assembly 04130B Deluxe Carpet Dryer * 12, 1 quart bottles **Required to use any accessory Page -34- Clarke Technology Operator's Manual IMAGE 26B... -
Page 35: Wiring Schematic 1/01
CLARKE TECHNOLOGY Image 26B Wiring Schematic 1/01 Clarke Technology Operator's Manual IMAGE 26B Page -35-... -
Page 36: Connection Diagram 1/01
CLARKE TECHNOLOGY Image 26B Connection Diagram 1/01 Page -36- Clarke Technology Operator's Manual IMAGE 26B... -
Page 37: Flow Diagram
CLARKE TECHNOLOGY Image 26B Flow Dagram 3/01 Clarke Technology Operator's Manual IMAGE 26B Page -37-... - Page 38 NOTES Page -38- Clarke Technology Operator's Manual IMAGE 26B...
- Page 39 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 SALES SUBSIDIARIES Technical Service - 1-800-356-7274 ALTO Canada Ltd., Rexdale Ontario ALTO U.S. Inc., Bowling Green, Ohio 43402 24 Constellation Ct. 1100 Haskins (416) 675-5830 ALTO Overseas Inc., Sydney (Australia) 1B/8 Resolution Drive...
- Page 40 RANTY OF MERCHANTABILITY, SHALL BE IMPLIED. A warranty registration card is provided with your Clarke Technology product. Return the card to assist Clarke Technology in providing the performance you expect from your new floor machine. ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764. CLARKE TECHNOLOGY POLYDUR TANK ®...