Table of Contents
Advertisement
Quick Links
E
Operator's
Vision 21i
Manual
VisionV
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or other property
could occur as well. You must have training in the operation of this machine before using it. If you
or your operator(s) cannot read English, have this manual explained fully before attempting to operate
this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes
de tratar el manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 78493B
2/00
CLARKE TECHNOLOGY
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Alto Vision V- 00590A
Summary of Contents for Alto Vision V- 00590A
- Page 1 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764. Form No. 78493B 2/00 CLARKE TECHNOLOGY Printed in the USA...
-
Page 2: Table Of Contents
Vision 21i - Vision V Connection Diagram, Front of Machine ............45 Vision 21i - Vision V Connection Diagram, Rear of Machine ............46 Vision 21i - Vision V Connection Diagram, Inside Rear Cover ............Page -2- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 3: Operator Safety Instructions
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your Clarke Technology machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. - Page 4 Do not use this machine as a step or furniture. Do not ride on this machine. CAUTION: Your machine warranty will be voided if anything other than genuine Clarke Technology parts are used on your machine. Always use Clarke Technology parts for replacement.
-
Page 5: Introduction & Machine Specifications
Introduction & Machine Specifications Introduction & Machine Specifications Clarke Technology’s newly designed Vision 21i & Vision V automatic scrubbers are efficient and superior floor cleaning machines. The Vision 21i uses two brushes or pads to scrub a path 21 inches wide. -
Page 6: Procedures For Transporting
10. As the machine begins to travel down the ramp, push the control handles toward the machine to maintain a slow downward speed. 11. Replace squeegee assembly, brush housings, & brushes or pad drivers after the machine is unloaded and ready to use. Page -6- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 7: Symbols Used On Vision 21I & Vision V
SYMBOLS USED ON VISION 21i & Vision V Warning Power On/Off Key Switch Traverse Speed Solution Control Brush Up/Down Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 8: Machine Control Panel 21I & Vision V
If a circuit breaker trips, determine which motor is not operating and turn the key switch "OFF". Wait five minutes and push the reset button back in. Turn the key switch "ON", and try again. An authorized service person should be contacted if the breaker trips again. Page -8- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 9: Machine Control Panel 21I & Vision V
MACHINE CONTROL PANEL (Vision 21i & Vision V) Figure #1 Figure #2 Figure #3 Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 10: Machine Controls And Features
To engage the brake, push the pedal down (Figure #6a). To release the brake, lift pedal up (Figure #6b). CAUTION: Do not activate the brake while the machine is moving. Figure #5. Figure #6b. Figure #6a. Page -10- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 11: How To Prepare The Machine For Operation
9. Install the tank, reconnecting hoses and replace the two screws attaching the solution tank to the rear of the frame. NOTE: Charge the batteries before using the machine. Figure #8 Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 12: Battery Maintenance
To clean the teminals and connectors, use a terminal and connector cleaning tool. Do not allow ammonia or bicarbonate of soda to get into batteries. Keep the batteries charged. Page -12- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 13: How To Charge The Batteries
For more instruction on the use of the charger, read the instruction book supplied with the charger. Figure #12 Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 14: How To Install The Brushes Or Pad Drivers
4. Turn the key switch "OFF". 5. Go to the front of the machine. 6. Push down on two sides of the brush or pad driver until the gimbals release. Page -14- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 15: How To Operate The Machine
2. Fill the solution tank with water. Figure#14b 3. Add a cleaning chemical to the water. for the correct amount, follow the directions shown on the container. 4. Replace the solution tank lid. Figure #15 Clarke Technology Operator's Manual - Vision 21i - Vision V... - Page 16 See figure #17. 8. To turn the machine, push the rear of the machine to the side. 9. When you stop the machine, turn the key switch "OFF". Page -16- Clarke Technology Operator's Manual -Vision 21i - Vision V...
-
Page 17: How To Clean A Floor
5. Leave the solution on the floor long enough for the solution to begin cleaning the floor. 6. Scrub the floor again with additional solution, picking up all the solution with the squeegee Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 18: How To Correct Problems In The Machine
Have an authorized service person repair the The charger is damaged. charger. Check voltage of each cell while discharging. The battery is defective. Connect the batteries. The batteries are disconnected. Page -18- Clarke Technology Operator's Manual -Vision 21i - Vision V... - Page 19 The machine does not run. Reset the circuit breaker. The machine loses power. Check wire connection to traverse motor. Check the battery connections. NOTE: If the problem continues consult an authorized service person. NOTES Clarke Technology Operator's Manual - Vision 21i - Vision V...
-
Page 20: Maintenance
6. Make sure brush housings and skirts are in position on the brush head. 7. Make sure the brushes are in position and installed correctly 8. Check the installation of the squeegee and squeegee hose. Figure #21 Page -20- Clarke Technology Operator's Manual -Vision 21i - Vision V... - Page 21 Use a clean cloth and wipe the surface of the machine. Charge the batteries. See the instruction in the section of Figure #22d this book called “How To Charge The Batteries”. Clarke Technology Operator's Manual - Vision 21i - Vision V...
- Page 22 5. Use a grease gun to lubricate the drive wheel and the casters. See figure #24. 6. Apply a thin lubricant to the drive chain. Page -22- Clarke Technology Operator's Manual -Vision 21i - Vision V...
- Page 23 "Y" up. Make very small adjustments and try it until a uniform flare is achieved. Changing the tilt may also require readjusting the squee- gee pressure. Figure #27 Clarke Technology Operator's Manual - Vision 21i - Vision V...
- Page 24 (Figure #29) and remove the filter screen (Figure # 30) and clean or replace it. Push filter assembly back inside frame. Figure #30 Page -24- Clarke Technology Operator's Manual -Vision 21i - Vision V...
-
Page 25: Accessories
11" Grit- Heavy 11443A 11" Grit-Medium11444A 11" Soft-Nylon 11441A 13" Poly 11438A 13" Grit-Heavy 11440A 13" Grit-Medium11439A 13" Soft Nylon 11437A Pad Drivers: Size Part No. 11" 17530A 13" 17531A Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 26: Vision 21I - Vision V Rear Cover Assembly Drawing
31 79 24 25 77 90 51 85 60... -
Page 27: Parts List
Solenoid, Brush Motor 962546 Screw, #10-24 X ½ 878514 Solenoid, 980675 Washer Vac, Speed Ctrl 69506A Cover Support, RH 68643A Plate, Wear 41811A Solenoid, For./Rev. 41444A Circuit Breaker 30A (Trav.) 1 Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 28: Vision 21I - Vision V Traverse System Assembly Drawing
CLARKE TECHNOLOGY Vision 21i - Vision V Traverse System Assembly Drawing 2/00 Page -28- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 29: Parts List
Shaft 883351 Grease Fitting 59944R Wheel Assembly 42K 30063A Sheild, Wheel Guard NIK 77266B Label, Parking Brake NOTE: Kindicates a change has taken place since last publication of this manual Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 30: Vision 21I - Vision V Squeegee & Squeegee Arm Assembly Drawing
CLARKE TECHNOLOGY Vision 21i - Vision V Squeegee & Squeegee Arm Assembly Drawing 1/97 ref. 26 17 Page -30- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 31: Parts List
Screw, -16 x 2¼ 37016A 67899A Washer, Flat 3/8 S.S. 85811A Screw - 18 x .75 66531A Swing Arm Pin 836711 Hair Pin 60416A Arm, Pivot 81207A Nut, -16 SS Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 32: Vision 21I - Vision V Brush Head Assembly Drawing
CLARKE TECHNOLOGY Vision 21i - Vision V Brush Head Assemby Parts List 9/98 51 66 Squeegee Arm Stop Asm. Page -32- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 33: Parts List
Head Pressure Sleeve 170892 Washer, Lock ¼ 82404A Spirol Pin, 70065A Label 26v 70066A Label, 21i *NOTE: #67 used with screws #62 only as needed to square up linkage bars #29. Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 34: Vision 21I - Vision V Solution/Vacuum System Drawing
CLARKE TECHNOLOGY Vision 21i - Vision V Solution/Vacuum System Drawing 9/98 34 33 51 52 55 34 14 15 Page -34- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 35: Parts List
Locknut 962987 Screw, 10-24 x 38985D Recovery Tank 962943 Screw, 8-18 x 1/2 PN 30405A Drain Hose, Solution 170915 Screw, ¼-20 x 85391A Screw, ¼-20 x 30410A Hose, Vac Motor Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 36: Vision 21I - Vision V Brush Housing Assembly
CLARKE TECHNOLOGY Vision 21i - Vision V Brush Housing Assembly Drawing 7/96 Page -36- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 37: Parts List
69090A Strap, L.H. 69078A Strap, L.H. 81104A Nut, 1/4-20 ESNA 81104A Nut, 1/4-20 ESNA 85737A Scr., 1/4-20 x 5/8 Hex 85737A Scr., 1/4-20 x 5/8 Hex 81301A Nut, 3/8-16 Jam Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 38: Vision 21I - Vision V Alternate Brush Motor (44809A) Assembly Drawing And Parts List
Refer to pages 30 and 31 in this manual for other parts. Ref. Part No. Description Qty. 980638 Washer, Lock 3/8 962244 Screw, 3/8-16 x 3/4 44809A Motor, Brush 53412A Head Pressure Spring Page -38- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 39: Vision 21I - Vision V Alternate Brush Motor (44809A) Drawing And Parts List
Brush Board Assembly (w/ Springs & Brushes) 448396 Brush Spring 40826A Brush Assembly 55657A Lead Assembly 55656A Lead Assembly 59805A Helical Washer 50515A Thru Bolt 44809A Shaft Key 54238A B.E. Bracket Assembly (Gear Box) Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 40: Vision 21I - Vision V Brush Motor (45037A) Drawing & Parts List
Seal - Oil 830846 Bracket 962955 Screw ¼-20 x 5¾ Hex 50577A Bracket Assembly 833102 Field Asm. w/Mag Clips 55133A Brush Holding Asm. 448396 Spring -Brush 40807A Brush Assembly Page -40- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 41: Vision 21I - Vision V Traverse Motor (45038A) Drawing & Parts List
Screw ¼-20 x 5¾ Hex 50577A Bracket Assembly 833102 Field Asm. w/Mag Clips 912206 Housing - Male Terminal Connector 912207 Terminal - Male 55133A Brush Holding Assembly 1 448396 Spring -Brush 40807A Brush Assembly Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 42: Battery Charger Drawing & Parts List
Strain Relief, A.C. Cord 837525 837525 Strain Relief, D.C. Cord 747553 747553 D.C. Cord Assembly 51986A 51986A A.C. Cord Assembly 51974A 908947 Housing 911470 911470 D.C. Plug Lock Key 795020 795020 Page -42- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 43: Vision 21I - Vision V Vac Motor (44917A)
Disc Bearing 59803A Washer, Neoprene *NOTE: #'s 3, 8, 10, 12, 16, 17, 19, 20, 21, 22, & 23 Bracket, Fan End are not available at this time. 58500A Spacer Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 44: Vision 21I - Vision V Electrical Schematic
CLARKE TECHNOLOGY Vision 21i - Vision V Electrical Schematic 7/99 Page -44- Clarke Technology Operator's Manual -Vision 21i - Vision V... -
Page 45: Vision 21I - Vision V Connection Diagram, Front Of Machine
CLARKE TECHNOLOGY Vision 21i and Vision V Connection Diagram 1/97 Front of Machine (Tank Removed) Clarke Technology Operator's Manual - Vision 21i - Vision V... -
Page 46: Vision 21I - Vision V Connection Diagram, Rear Of Machine
CLARKE TECHNOLOGY Vision 21i and Vision V Connection Diagram 1/97 Rear of Machine (Rear cover open) Page -46- Clarke Technology Operator's Manual -Vision 21i - Vision V... - Page 47 CLARKE TECHNOLOGY Vision 21i and Vision V Connection Diagram 1/97 Inside Rear Cover Clarke Technology Operator's Manual - Vision 21i - Vision V...
- Page 48 NOTES Page -48- Clarke Technology Operator's Manual -Vision 21i - Vision V...
- Page 49 Customer Service Headquarters and Factory +46 31 706 73 00 2100 Highway 265 Springdale, Arkansas 72764 ALTO Norge A/S, Oslo (Norway) (501) 750-1000 Bjornerudveien 24 N-1266 Technical Service Clarke Technology Operator's Manual - Vision 21i - Vision V +47 2275 1770 1-800-356-7274...
- Page 50 (90) days from date of sale to the original user will be repaired or replaced with one of equal specification at our option, F.O.B. any authorized Clarke Technology Sales or Service Branch, with no charge to the user, except transportation costs.