Installation Information; Fireplace Location - Monessen Hearth 624DVNVC Installation And Operating Instructions Manual

INSTaLLaTIoN INFoRMaTIoN

FINIShING MaTERIaL
NoTE: Any remote wiring (i.e. remote control, wall switch,
and optional fan) must be done prior to final finishing to
avoid costly reconstruction.
Only noncombustible materials (i.e. brick, tile, slate, steel,
or other materials with a UL fire rating of Zero) may be used
to cover the black-painted face of the appliance. A 300°F
minimum adhesive may be used to attach facing materi-
als to the black surface. If joints between the finished wall
and the fireplace surround are sealed, a 300°F minimum
sealant material (General Electric RTV103 or equivalent)
must be used. Combustibles may come to the top and side
edges but not overlay the face.
INSTaLLaTIoN aNd oPERaTING INSTRuC-
TIoNS
This gas fireplace should be installed by a qualified installer
in accordance with local building codes and with current
CSA-B149 (.1 or .2) Installation codes for Gas Burning
Fireplaces and Equipment. If the unit is being installed in a
mobile home the installation should comply with the current
CAN/CSA Z 240 .4 code.
FOR U.S.A. Installations follow local codes and/or the cur-
rent National Fuel Gas Code. ANSI Z223.1.

FIREPLaCE LoCaTIoN

For Safe Installation and operation Please Note
The Following:
1. This fireplace gives off high temperatures and should
be located out of high traffic areas and away from
furniture and draperies.
2. Children and adults should be alerted to the hazards
of the high surface temperatures of this fireplace and
should stay away to avoid burns or ignition of cloth-
ing.
3. Caution, due to high glass surface temperature children
should be carefully supervised when they are in the
same room as the fireplace.
4. Under no circumstances should this fireplace be modi-
fied. Parts removed for servicing should be replaced
prior to operating the fireplace again.
5. Installation and any repairs to this fireplace should
be carried out by a qualified service person. A profes-
sional service person should be contacted to inspect
this fireplace annually. Make it a practice to have all of
your gas fireplaces checked annually. More frequent
cleaning may be required due to excess lint and dust
from carpeting, bedding material, etc.
6. Control compartments, burners and air passages in this
fireplace should be kept clean and free of dust and lint.
Make sure that the gas valve and pilot light are turned
off before you attempt to clean this fireplace.
42D0200
7. The venting system (chimney) of this fireplace should
be checked at least once a year and if needed your
venting system should be cleaned.
8. Keep the area around your fireplace clear of combus-
tible materials, gasoline and other flammable vapor and
liquids. This fireplace should not be used as a drying
rack for clothing, nor should Christmas stockings or
decorations be hung on or around the fireplace.
9. Under no circumstances should any solid fuels (wood,
coal, paper or cardboard etc.) be used in this fire-
place.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
11. When the fireplace is installed directly on carpeting,
vinyl tile or any combustible material other than wood,
the fireplace must be installed on a metal or wood panel
extending the full width and depth of the fireplace.
12. This fireplace requires adequate ventilation and com-
bustion air to operate properly.
13. This fireplace must not be connected to a chimney flue
serving a separate solid fuel burning fireplace.
14. When the fireplace is not in use it is recommended that
the gas control valve be left in the "OFF" position.
This appliance has been approved for after-market
mobile home installations.
IMPORTANT:
PLEASE READ THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace ON.
It is normal for fireplaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or car engine.
It is not unusual for your Monessen gas fireplace to give
off some odor the first time it is burned. This is due to the
curing of the paint and any undetected oil from the manu-
facturing process.
Please ensure that your room is well ventilated — open
all windows.
It is recommended that you burn your Monessen fireplace
for a least ten (10) hours the first time you use it. If the
optional fan kit has been installed, place the fan switch
in the "OFF" position during this time.
Designer Series Gas Fireplaces
9