Electrical Wiring Information - Jenn-Air CCGX2420 Installation Manual

Jointhe appliance p ressure regulator s upplied withthis appliance t o the Whena dividing wallis present a nda flexibleconnector i s usedit is
entrance threads ofthe GasManifold. Theappliance r egulator is marked recommended for convenience, in bothinstallation and service, t he
witha directional arrowindicating c orrect d irection o f gasflow.Ensure the flexible connector, itself,passthrough the dividing wall.Anyflexible
appliance r egulator i s installed withthe arrowpointing towardthe gas connector used withthisappliance mustsatisfy allrequirements
manifold entrance. Tighten the appliance regulator t o 20to 30 ft-lbsof stated inthetextaccompanying figure 3.
"nrque. Unless prohibited by IDeal codesor ordinances, a newA.G.A.- Certified,
IMPORTANT I flexible metal a ppliance c onnector maybeusedtoconnect t hisappliance
- Never t ighten tomorethan35ft-lbsoftorque. A lways u seanapproved to itsgassupply. T heconnector m ust h aveaninternal d iameter n etless pipeje ntcompound resistant totheaction ofLPgas. thannominal 1/2"NPTpipeandbenomorethan5 feetin length. A 1/2"
NPTx 1/2" flareunionadapteris requiredat eachend of the flexible
Install theappliance i nits counter c utout, connector, if a flexible connector i s usedassure thatboththe appliance
pressure r egulator andmanual s hut-oft v alvearejoinedsolidlyto other
Make the gasconnection t o the inletofthe appliance p ressure regulator permanent hardpiping (either g assupply orthe appliance m anifold) soas
with112" male pipethreads, to bephysically s tationary. Seeillustrations below:
CAUTION: Do notattempt t o attach theflexibleconnector directly to an
Installa manual s hut-off v alvein an accessible I Deation inthegasline external pipethread. C onnection requires f lareunion adapters.
ahead oftheappliance p ressure r egulator andexternal tothisappliance for
thepurpose ofturning onor shutting o ffgastotheappliance. IMPORTANT
Make additional pipeconnections asnecessary a head oftheshut-off v alve Test a llconnections forgasleaks witha soapandwater s olution orother
tothegassupply source. Assure a;;pipejointconnections aregastight, accepted l eakdetedionmeans. N evertestfor gasleakswithanopen
fame.
IMPORTANT
Testall jointsforgasleakswith a soapandwatersolutionor other PRESSURE TESTING
accepted l eakdetection means. N ever t estfor gasleakswithanopen
flame. Theappliance mustbe isolated from the gassupplypipingsystemby
closing its individual manual s hut-off valveduringanypressure testingof
thegassupply pipingsystem at testpressures e qual t o or lessthan1/'2
PS/G(3.5kPa).
"_ This appliance, a s well as its indMduaJ shut-off valve, must be
disconnected from the gassupplypipingsystemduringany pressure
testing ofthesystem attestpressures i n excess o f lj2 PSIG(3.5kPa).
MANIFOLD P_PE
Whenchecking a ppliance regulator'function, makecertainpressureof
natural g as supplyis between6 and 14 inchesof watercolumn or, if
_,PPL lANCE PRESSURE /- converted f orLPgas,between 11and14inches.
_EGULATOR, SUPPLIED
(OSSERvE O,R_CT_O. ELECTRICAL WIRING INFORMATION
0r GAS FLOW ARROW)
appliance equipped agrounded typepower grounded
This is
with
cord. A
outlet m ust b eprovided, itisrecommended, forconvenience, theoutlet be
FLAREos_@
UNI O N 1/2" NPT located (withreference t ofigure4) asbelow:
ADAPT
P IPE
NIPPLE
FL_×_LE_..._ _ -- _....
APRL IANCE
CONNECTQ
-1
SHU[
OFF
FLARE VALVE
UNION _
ADAPTOR _-_
GAS_ 1/2" NPT
SHUT-OFFvALVE _ _PIPE
1/2" NPT-_
P_PE _
FIGURE 3 /
t
• If thealternative p ipingmethod shownin figure3 is selected for the CABI NET BOTTOM
installation, no ground joint union is required. (Theflexibleappliance FIGURE 4
connector illustrated provides theunion joints necessary forservicing,)