Hitachi DH 25PA Handling Instructions Manual
  1. Manuals
  2. Brands
  3. Hitachi Manuals
  4. Drill
  5. DH 25PA
  6. Handling instructions manual
Hitachi DH 25PA Handling Instructions Manual

Hitachi DH 25PA Handling Instructions Manual

Hide thumbs Also See for DH 25PA:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual, Technical Data and Service Manual
Hammer Drill
DH 25PA
DH 25PB
•

Handling instructions

Read through carefully and understand these instructions before use.

Advertisement

Table of Contents
loading

Related Manuals for Hitachi DH 25PA

Summary of Contents for Hitachi DH 25PA

  • Page 1: Handling Instructions

    Hammer Drill DH 25PA DH 25PB • Handling instructions Read through carefully and understand these instructions before use.
  • Page 2 <DH25PA> <DH25PB> <DH25PB>...
  • Page 3 <DH25PB>...
  • Page 4 12 mm – Drill bit Part of SDS-plus shank Front cap Grip Dust cup Dust collector (B) Change lever Drill chuck Chuck adapter Driver bit Socket Chuck adapter (D) (DH25PB) Side handle Stopper Mounting hole Tape shank adapter Cotter Rests Core bit Core bit shank Thread...

  • Page 13: General Safety Rules

    d) Remove any adjusting key or wrench before GENERAL SAFETY RULES turning the power tool on. A wrench or a key left attached to a rotating part of WARNING! the power tool may result in personal injury. Read all instructions e) Do not overreach.

  • Page 14: Specifications

    4. Use auxiliary handles supplied with the tool. PRECAUTIONS ON USING HAMMER DRILL Loss of control can cause personal injury. 5. Always hold the body handle and side handle of the 1. Wear ear protections power tool firmly. Otherwise the counterforce Exposure to noise can cause hearing loss.
  • Page 15 Outer diameter Taper mode Applicable drill bit 11.0 mm 12.3 mm Morse taper (No.1) Drill bit (taper shank) 11.0 – 17.5 mm 12.7 mm Morse taper (No.2) Drill bit (taper shank) 21.5 mm 14.3 mm A-taper Taper shank adapter formed A-taper or B-taper 14.5 mm is provided as an optional accessory, but the 17.5 mm...
  • Page 16 Center pin Core bit (outer diameter) Core bit shank – 25 mm 29 mm 32 mm Core bit shank (A) Center pin (A) 35 mm 38 mm 45 mm 50 mm Center pin (B) 65 mm Core bit shank (B) 80 mm 90 mm Do not use core bits with...

  • Page 17: Prior To Operation

    7. Dust cup and Dust collector (B) 8. Hammer grease A 500 g (in a can) 70 g (in a green tube) 30 g (in a green tube) Dust cup Dust collector (B) Optional accessories are subject to change without notice. CAUTION: APPLICATIONS The dust cup and dust collector (B) are for exclusive...
  • Page 18 3. Rotation only (DH25PB) 6. Using the stopper (Fig.10) The hammer drill can be set to rotation only mode (1) Loosen the knob on the side handle, and insert the by rotating the change lever fully clockwise to stopper into the mounting hole on the side handle. mark.

  • Page 19: Maintenance And Inspection

    6. Service parts list CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance.
  • Page 20 DH25PB The exploded assembly drawing should be used only for authorized service center.
  • Page 21 Tube (D) Washer (B) Cord Armor Cylinder Case Seal Lock Screw (W/Washer) M5×25 Hex. Socket Hd. Bolt (W/Flange) M5×25 Switch (B) HITACHI Label Third Pinion Noise Suppressor Ball Bearing (6001DDCMPS2L) Support (B) Washer Pillar Terminal Handle Cover Second Gear Stopper Washer Tapping Screw (W/Flange) D4×20...
  • Page 24 Hitachi Koki Co., Ltd. Code No. C99099024 F Printed in China...

Table of Contents